HEIGHT STRIP CAMERA window a HSW-H30 Pen St d f Count INSTALLATION OPERATING INSTRUCTIONS WWW.COMPUTARGANZ.
12. Power Lines - An outdoor system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits. When installing an outdoor system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. U.S.A. models only - refer to the National Electrical Code Article 820 regarding installation of CATV systems. 13.
1 SAFETY PRECAUTIONS UNPACKING Unpack carefully. This is electromechanical equipment and should be handled with care. Check for the following items: • Verify the unit model number. • Verify that parts listed below have been included. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. HSW-H30 – Height Strip w/ one color camera and 3.0mm lens, white housing.
2 4 SERVICE If the unit ever needs repair service, the customer should contact CBC (America) Corp. for return authorization and shipping instructions. 3 DESCRIPTION The HS Series of Height Strip camera housings are intended to improve in-store security in two ways. First, when installed next to the main entrance of a store, cameras within the store will capture a subject’s height when exiting as he or she passes the brightly colored labels.
VOLTAGE & MAX WATTAGE 6.2 Camera Removal/Relocation, and Installing Accessory Camera Color Camera 95mA (Max) @ 12VDC 1. Each Height Strip ships from the factory with a single camera installed that looks through the viewing window located at the 5-1/2 foot mark. Two other viewing windows are provided at the 4-1/2 foot mark and 6-1/2 foot. 2. To relocate the existing camera, use a 5.5mm (or 7/32”) nut driver to remove the M3 nut that attaches the camera bracket to the base (see Figure 4).
7. Fit the cover back over the base and tighten down the four (4) M3 screws to secure. 8. Locate the marked countersink in the cover. 9. Drill out an appropriate sized hole in the Height Strip cover using the following guidelines: 7 INSTALLATION 7.1 Side-mounted cameras Note: If NOT using the side-mounted camera feature of the Height Strip, proceed to the next applicable section. 1. Refer to Figure 5 when side-mounting a camera. 2.
10. Unscrew the base and set aside. Drill out the remaining two mounting holes (3/16” drill bit) and insert the remaining wall anchors. 11. At the desired through-hole location(s), drill a hole in the mullion wide enough to accept the customer-provided power and video cables. 12. Feed the cables down into the mullion and fish them out of the through-hole. 13. Hang the Height Strip back on the mounting screw in the mullion and feed the power and video cables into the unit. 14.
7.3 Installing the Unit onto a Solid Wall 7.4 Installing the Unit using the Accessory Wall Bracket (MT-HS) 1. Refer to steps 1 to 6 above. Replace fasteners and wall anchors from the hardware kit with customer-supplied components as desired. The through-hole size for the wall mounts is sized for a #8 screw (approximately 0.175” diameter). 2. Use the base as a template to mark the hole location of the other two mounting holes.
Notches designate 5-foot mark. The mounting holes in the Height Strip base are not symmetrical. Take care to select the correct hole for your particular application. Figure 9 8. Remove the cover from the Height Strip by removing the four (4) cross-recessed screws. 9. Orient the Height Strip base as desired. Secure the base to the MT-HS accessory bracket using three (3) M4 screws and three (3) M4 nuts from the hardware kit sent with the MT-HS. 10.
DIMENSIONAL OUTLINES Back View (ø.19 X3) MOUNTING HOLES 14.7 374.7 9.7 247.7 Side View Front,Top, Down, Bottom Up Top Down Bottom Up 1.7 43.2 1.6 40.6 7.5 190.5 Viewing window for camera 12 304.8 12 304.8 Viewing window for camera Viewing window for camera 34 863.6 in mm 10 2.5 63.5 6 152.4 3 76.
Addendum to Installation and Operating Instructions Manufacturer’s Part Number: Amended Installation Manual Part Number: HSW-H30 100 0284 002 CBC Amend the following sections of the installation manual shipped with the above referenced product to read: Section 7 – INSTALLATION 7.5 Adjust the camera settings using the On-Screen Display (OSD) The camera used in this model includes a keypad for accessing the On-Screen Display (OSD) to adjust the camera settings.
Section Menu Item WB (White Balance) Day & Night Function Motion Default WB Mode Sub-Menu Item - R-Y Gain B-Y Gain - 100 100 D&N Mode (Auto, Ex-CDS, see Description) Auto Auto Color B&W EX-CDS C_SUP, A_SUP - 35 / 32 0~100 Mirror Sharpness - Off 020 Off 0 ~ 30 Monitor - Mode1 Mode1, Mode2 Gamma (User) 0.45 LSC (Set Level) Off 0.45 0.60 1.
Section Menu Item Motion Cont’d Hold Time Alarm Privacy Masking Setup (SET) System Exit Sub-Menu Item - Default 003 On 0 ~ 100 n/a Dot SEL - Dot XY Move XY Color Set Black Title (On) Off L_Top L_Bot R_Bot R_Top Black White Red Green Blue Magenta Cyan Off On Manual DPC (Manual) Off Auto DPC (Auto) Off OLPF - 650 650 850 OSD Color - Blue Camera ID - 1 Black, White Red, Green Blue, Cyan Magenta 0 ~ 255 Communication (ON) Off Off On Language - English Factory Set - O
