User Manual

All alarms to be connected in the house should
be put into ‘Learn Mode’ by sliding the switch on
the back of the alarm to the ‘Learn Mode’ position.
Please note: The learn switch placed on the back
of the alarm can only be in learn position when
the alarm is disassembled from the power supply
unit. The learn switch will automatically switch to
normal position when the alarm head is tted to
the power supply.
The red LED will light up to indicate that ‘Learn
Mode’ has been selected.
Do not remove the battery during ‘Learn Mode’ as
this will interrupt the learn process.
Press and hold the test button at one alarm only,
until it beeps and the LED ashes. This alarm will
become the master and will start sending out a
specic house code to the other alarms.
As the other alarms receive the specic house
code, they will also ash the LED light.
When the red LED light flashes on all alarms,
they are connected and MUST BE SWITCHED
OUT OF ‘LEARN MODE’ and installed.
Mains powered smoke alarm device
Commercial reference: 2201
Developed by CAVIUS
The smoke alarm is designed for private homes.
PLEASE READ THE USER GUIDE
CAREFULLY BEFORE INSTALLATION AND
RETAIN FOR FUTURE USE.
SAFETY INSTRUCTIONS:
The device comes with a 3V lithium battery. Bat-
teries are to be handled with care and battery pow-
ered devices should be kept out of reach of chil-
dren. Do not try to recharge or burn the batteries.
TECHNICAL INFORMATION:
The smoke alarm is powered by mains power (110-
230V AC), with a lithium back-up battery CR2.
It can be RF interlinked with other 2201 alarms,
and with other CAVIUS Wireless Family alarms.
The maximum number of alarms that can be inter-
linked within a house group are 32.
Please note: These must be alarms from the CAVIUS
The distance between interlinked alarms depends
on the house layout and they should always be
tested after installation. It is not advised to install
alarms with a separation of more than 10m.
Diameter: 97mm. Height: 41mm (without mount-
ing base) 52mm (with mounting base).
Complies to standards: EN14604:2005 + AC:2008,
EN300-220, EN50130-4:2011, EN60065.
EN60950-1, RoHs, Reach.
1. HOW TO SET UP AND CONNECT ALARMS:
Start by pulling out the battery isolation strip in the
battery compartment as shown. Please note: RF
connection is done with the device powered with
battery only. You do not have to connect the power
supply. The product label must not be removed
as it contains important information regarding the
product.
Label the original “Learn” alarm in order to easily
add new CAVIUS Wireless Family alarms to the
system.
2. THE BEST AREAS TO INSTALL THE SMOKE
ALARM:
• Note the local country regulations regarding
installation.
• Note the local regulations about information
to your insurance company regarding installed
smoke alarms.
• Install an alarm between possible re sources
and bedrooms as a minimum.
• Install alarms on each oor of the house, in
hallways and stairways.
• Alarms in each room such as bedrooms and
living rooms.
Additional alarms increase the security.
3. AREAS WHERE NOT TO INSTALL SMOKE
ALARMS:
• In dusty rooms
• At the top of a high pointed ceiling, in ceiling
corners, and within 50cm of a wall.
• In rooms where temperature goes outside the
range +4
o
to 38°Cor above 90% relative humidity
not condensing.
• In kitchens, garages, laundries, or too close to
replaces; areas where either dampness, gases
or smoke could occur.
Place the alarm where it is reachable in order to
test the alarm and for maintenance.
4. PLACEMENT:
The smoke alarm is designed to be installed on
a ceiling.
With a minimum of one smoke alarm per oor and
a maximum distance between smoke alarms of
10 meters.
For ceiling installation:
The smoke alarm should be a minimum of 50cm
from the wall.
For cathedral or peak ceiling:
UK
ISOLATION
STRIP
DO NOT
REMOVE THE
PRODUCT LABEL
1
Minimum 50cm
from wall
Wall
Ceiling
Peak ceiling
Minimum 50cm
from peak
2
LEARN MODE
1
NORMAL MODE
CHAMBER
FILTER
OPTIONAL HOLE
FOR LAMP WIRE
TEST BUTTON
SIREN
RED & GREEN LED
1
2