Installation Guide and Users Manual CAVALIERE Model-Z01(IS)CL IMPORTANT: Read and save these instructions. NOTICE: Installer: Leave this guide with the homeowner Homeowner: Keep this guide for future reference Wall Mount Range Hood Rev. 1025u.
Important Safety Notice Read all Instructions before Installing and operating this appliance • • • • • The installation in this manual is intended for qualified installers, service technicians or persons with similar qualified background. Installation and electrical wiring must be done by qualified professionals and in accordance with all applicable codes and standards, including fire-rated construction. DO NOT attempt to install this appliance yourself.
Important Safety Notice Read all Instructions before Installing and operating this appliance • • • Clean ventilating fan frequently. Always use appropriate cookware and utensils size. Always use cookware appropriate for the size of the surface element. To reduce the risk of injury to persons in the event of a stove top grease fire: • • • SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn OFF the burner. BECAREFUL TO PREVENT BURNS.
Table of Contents INSTALLATION Tools needed....................................................3 Parts supplied...................................................4 Venting requirements.......................................5 Mount heights & clearance...........................5-6 Calculating vent system length.......................6 Venting methods..............................................7 Electrical requirements....................................8 Preparation.........................................
Range hood Lower Chimney Upper Chimney Support parts Optional Duct Tube Ducting Transition Bracket Screw Set A1:Qty=4 A2:Qty=2 B1:Qty=4 B2:Qty=2 C1:Qty=16 C:Qty=6 C2:Qty=32 Stainless steel Baffle filter
Venting Requirements • • • • • • • Height & Clearance Vent system must terminate to the outside (roof or side wall). DO NOT terminate the vent system in an attic or other enclosed area. DO NOT use 4” (10.2 cm) laundry-type wall caps. Use metal/aluminum vent only. Rigid metal/ aluminum vent is recommended. DO NOT use plastic vent. Always keep the duct clean to ensure proper airflow. Calculate the following figures before installation: 1. Distance from the floor to the ceiling. 2.
IMPORTANT: • A minimum of 6” round (standard for this range hood) or 3-1/4 x 10” rectangular duct (purchased separately) must be used to maintain maximum airflow efficiency. • Always use rigid type metal/aluminum ducts if available to maximize airflow when connecting to provided duct. • Please use Duct Run Calculation below to compute total available duct run when using elbows, transitions and caps. • ALWAYS, when possible, reduce the number or transitions and turns.
Venting Methods • • This range hood is factory set for venting through the roof or wall. Vent work can terminate either through the roof or wall. To vent through a wall, a 90° elbow is needed. IMPORTANT: • • • • NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside. Use metal/aluminum duct work only. Fasten all connections with sheet metal screws and tape all joints with certified Silver Tape or Duct Tape.
Electrical Requirements IMPORTANT: For Europe and Other Countries with 220~240V/50Hz, please observe your local governing codes and ordinances. It is the customer’s responsibility: • To contact a qualified electrical installer. • To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 — latest edition*, or CSA Standards C22. 1-94, Canadian Electrical Code, Part 1 and C22. 2 No. 0-M91 - latest edition** and all local codes and ordinances.
Preparation WARNING Advanced Preparations: 1. Be familiar with the controls of the range hood by reading through Range Hood Operations, Page 12. 2. Place the range hood on a flat, stable surface. Connect the Excessive Weight range hood to a designated standard outlet, 110~120V/60Hz Require three or more person to move and (220~240V/50Hz for Europe & other countries), AC only install this range hood. Spinal or other bodiand turn on the range hood.
Installation Installations (refer to page 4 & 11 for parts): 1. Measure the distance between stove top and the bottom of range hood. A distance of 28” to 31” is required. 2. Make sure the range hood is level and not tilted. Mark the locations of the hanging bracket holes on the roof as shown in Figure 3A and Figure 3B. 3. Place the mounting bracket directly above the range hood, level it, and mark the locations of the mounting bracket holes on the roof. 4.
Installation (Continued) 8. Calculate the height of the duct tube and extend approximately 6” (15 cm) longer than required, connect the lower end of the duct tube to the range hood and the upper end to the vent system. Make sure the main electrical supply remains disconnected then connect power plug to the electrical cord or wall plug. 9. Have one person carefully position both upper and lower chimneys on the range hood, let the second person slide the sides of the chimneys into the 1/8” gap.
Range Hood Operations & Wiring Diagram Control Panel Layout and Buttons Configurations: Light Decrease Value Blower Speed Indicator Power /Timer Increase Value Power-Off Delay Digital Timer/Clock The Canopy hood is designed to remove smoke, cooking vapors and odors from the cook top area. For best results, start the range hood before cooking and allow it to operate several minutes after the cooking complete to clear all smoke and odors from the kitchen.
Range Hood Operations & Wiring Diagram (Continued) Control Panel Layout and Buttons Configurations: Light Decrease Value Blower Speed Indicator • Power /Timer Increase Value Power-Off Delay Digital Timer/Clock Controls: • Activating the timer function: • While the blower(motor) is running, press Power button once to enter Power-Off Delay Timer, The working time is 3 minutes which is changeless and the range hood will turn off automatically then.
Range Hood Operations & Wiring Diagram (Continued) Control type - Touch Sensitive Version (Four speed with type GU10 bulb) Page 14
Range Hood Measurements Page 15
Troubleshooting 1. If the range hood does not operate after installation: • • Check if the range hood has been plugged in, make sure that all power has been turned back on and all electrical wiring are properly connected. Swap out light assembly to working ones to determine whether it is caused by defective bulbs. (See Replacing the light bulbs, page 16) 2. The range hood vibrates when the blower is on: • The range hood might not have been secured properly on to the ceiling. 3.
Use and Care Information WARNING — TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer. Before servicing or cleaning unit, switch power off at service panel and lock switch power off at service panel and lock service panel to prevent power from being switched on accidentally.
Maintenance SAFETY WARNING: Never put your hand into area housing the fan while the fan is operating! For optimal operation, clean range hood and all baffle/spacer/filter/grease tunnel/oil container regularly. Regular care will help preserve the appearance of the range hood. Cleaning Exterior surfaces: • Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent (e.g.
Warranty TO OBTAIN SERVICE UNDER WARRANTY: You must present proof of original purchase date. Please provide an original dated proof of purchase (sales receipt / invoice) in order to obtain service under warranty. One Year Parts Warranty: For one year from the date of original purchase, your local reseller will provide free of charge, non-consumable replacement parts or components that failed due to manufacturing defects.
Disclaimer Carefully inspect all items for damages before accepting delivery. note any damages on the freight bill or express receipt. request name and signature of the carrier’s agent and keep copy to support your claim. Upon acceptance of items, owner assumes responsibility for its safe arrival. Report damages to the carrier and file a claim immediately. Failure to do so may result in the denial of your claim. The carrier will furnish you with necessary forms for filing a claim.
Your Notes Page 21
Your Notes Page 22
