UNDERCABINET RANGE HOOD 30 Installation & User Manual IMPORTANT NOTICE: Read and save these instructions. Installer: Leave this guide with the homeowner. Homeowner: Keep this guide for future reference.
Important Safety Notice READ ALL INSTRUCTIONS BEFORE INSTALLING AND OPERATING THIS APPLIANCE Your safety and the safety of others is very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed. This is the safety alert symbol.
Important Safety Notice • Ducted fans MUST always be vented to the outdoors. • DO NOT vent exhaust into spaces between walls, crawl spaces, ceiling, attics or garages. • Any old duct work should be cleaned or replaced if necessary to avoid the possibility of a grease fire. Check all joints on duct work to insure proper connection and all joints should be properly taped. • Use only metal ductwork and this unit MUST be grounded.
Table of Contents INSTALLATION Tools Needed...............................................................3 Parts Supplied .............................................................4 Venting Requirements..............................................5 Height & Clearance ...................................................6 Duct Size Upgrade Calculator ..............................6 Venting Methods ........................................................7 Electrical Requirements ...........................
Parts Supplied Range Hood (Design will vary with model) or Baffle Filter Spacer Stainless Steel Baffle Filter Range Hood Mounting Bracket Grease Catch Qty: 6 PCS (For dry wall or sheet rock only) Qty: 6 PCS Qty: 6 PCS Flexible Duct Tube Pg 4
Venting Requirements • Vent system must terminate to the outside (roof or side wall). • DO NOT terminate the vent system in an attic or other enclosed area. • DO NOT use 4” (10.2 cm) laundry-type wall caps. • Use metal/aluminum ducting only. Rigid metal/aluminum ducting is recommended. • Always keep the duct clean to ensure proper airflow. • Calculate the following figures before installation. • Distance between the countertop/stove to the range hood. (Recommended 27" to ~30").
Height & Clearance IMPORTANT: • A minimum of an 8" round duct must be used to maintain maximum airflow efficiency. • A flexible 8" round duct is provided for convenience and for use in difficult installations, however always attempt to use a smooth metal rigid type of ducting to maximize airflow efficiency. • ALWAYS, when possible, reduce the number or transitions and turns. If long duct run is required, increase duct size to. If a reducer is used, install a long reducer instead of a pancake reducer.
Venting Methods • This range hood is factory set for venting through the roof or wall. • Vent work can terminate either through the roof or wall. To vent through a wall, a 90° elbow is needed. IMPORTANT: • NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside. • Use metal/aluminum duct work only. • Fasten all connections with sheet metal screws and tape all joints with certified duct tape or equivalent.
Electrical Requirements IMPORTANT: Observe all governing ordinances and local codes. (Please consult with a qualified electrician for any electrical wiring) It is the customer’s responsibility: • To contact a qualified electrical installer. • To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 — latest edition*, or CSA Standards C22. 1-94, Canadian Electrical Code, Part 1 and C22. 2 No.
Preparation Advanced Preparations: 1. Familiarize yourself with the controls of the range hood by reading through Range Hood Operations, Page 13. 2. Place the range hood on a flat, stable surface. Connect the Severe Injury range hood to a designated standard outlet (please refer the Rotating fan can cause severe product label for the suitable voltage of this unit) and turn injury. Stay clear of fan when power is present. on the range hood.
Installation Installations (refer to Page 4 for Parts Supplied): 1. Measure the distance between the stove top and the bottom of range hood. A *distance of 27” to 30” is recommended. *Due to different ceiling height configurations, recommended height may not be applicable. 2.
Installation (Continued) (B) Mounting this range hood onto a vertical wall using the Range Hood Mounting Bracket: 1) Attach the Range Hood Mounting Bracket onto the range hood body. (Recommended to use an anti-vibration thread glue) Fasten screws securely. Figure 3.
3. Installation (Continued) 3. Install the baffle filters into the range hood. Figure 8. a) Angle the baffle filter so that the rear edge of the baffle filter enters the range hood cavity, and touches the back wall of the range hood. b) Then lift the front edge of the baffle filter so that it aligns with a groove in the lower front panel of the range hood assembly. c) Then slide the baffle filter towards the front of the range hood body, into the groove of the lower front panel of the range hood assembly.
Range Hood Operations Control Panel, Display and Functions: In addition to the remote control feature, this range hood is also equipped with a heat sensor that will self-calibrate in 5 seconds when the range hood is first electrically activated and beeps when self-calibration is done. To con- serve energy, the LCD panel will turn off automatically after 5 seconds of inactivity.
Range Hood Operations Control Panel, Display and Functions: Activating Light Function: • Press Light button once to turn on the lights, and once again to turn off the lights. CAUTION: DO NOT touch the lights or surrounding surface until turned OFF and allowed to cool. Activating Power-Off Delay Function: • While the range hood is on and the blower is running, press Power-Off Delay button to activate delay off timer and “Timer Shutoff” icon will appear in LCD panel.
Troubleshooting If the range hood or light does not operate after installation: • Check if the range hood has been plugged in, make sure that all power has been turned back ON, and all electrical wiring are properly connected. Swap out light bulb to working ones to determine • whether it is caused by defective bulbs. See Replacing the light bulbs on Page 20. The range hood vibrates when the suction is on: • The range hood might not have been secured properly on to the ceiling or wall.
Use and Care Information Operations: • Read and understand all instructions and warnings in this manual before operating the appliance. Save these instructions for future reference. • Always leave safety grills and filters in place. Without these components, operating blowers could catch on to hair, fingers and loose clothing. • NEVER dispose cigarette ashes, ignitable substances, or any foreign objects into blowers • NEVER leave cooking unattended.
Measurements and Diagrams 1. All measurements in parenthesis are in millimeters. 2.All inch measurements are converted from millimeters, therefore inch measurements are estimated.
Electric Schematic AC_L AC_N MO_N Black Live White Neutral White Fan (-) Green MO_1 MO_2 MO_3 Blue Fan 1 Pink Fan 2 Red Fan 3 Orange Fan 4 MO_4 12uf/250v (110v) 4uf/500v (220v) White Lamp (-) MOTOR Lamp (+) Black * Subject to change without notice, please contact your local reseller for details.
Maintenance SAFETY WARNING: Never put your hand into area housing the fan while the fan is operating! For optimal operation, clean range hood and all baffle/spacer/filter/grease tunnel/oil container regularly. Regular care will help preserve the appearance of the range hood. Cleaning Exterior Surfaces: • Clean periodically with hot soapy water and clean cotton cloth. DO NOT use corrosive or abrasive detergent (e.g.
Maintenance (Continued) Hazard of Burns! Light bulb become extremely hot when turned on. DO NOT touch bulb until switched off and cooled. Touching hot bulbs could cause serious burns. Replacing The Light Bulb: • Check the range hood tag for lamp specifications. Halogen bulbs will not work on "LED" models (they will lightly pulse or flash). • Before performing any task outside of basic operation, turn off the power supply and/or unplug the unit.
Warranty One Year Parts Warranty: For one year from the date of original purchase, your local reseller will provide free of charge, non-consumable replacement parts or components that failed due to manufacturing defects. Subject to the conditions and limitations set forth below, your local reseller will, at its option, either repair or replace any part of its products that prove defective by reason of improper workmanship or materials.
Disclaimer Carefully inspect all items for damages before accepting delivery. Note and picture any damages to the external box, contents or item to the carrier and written on the freight bill or delivery receipt. Request name and signature of the carrier’s agent and keep copy to support your claim. Upon acceptance of items, owner assumes responsibility for its safe arrival. Report damages to the carrier and file a claim immediately. Failure to do so may result in the denial of your claim.
21700 Barton Road, Colton, California 92324 USA Phone Number: (800) 827-5950 CavaliereHoods.
