120 Self-Flushing Self Washing Cat Litter Box - Manual Operation

IMPORTANT SAFETY INSTRUCTIONS
To Prevent Risk of Fire, Electric Shock, or Injury to People and Pets.
TO PREVENT FIRE or shock hazard, do NOT expose the
CatGenie Processing Unit to rain or sources of splashing
water. Do NOT operate the CatGenie with wet hands.
READ ALL INSTRUCTIONS BEFORE INSTALLING
AND USING YOUR CATGENIE. USE THE
CATGENIE ONLY FOR ITS INTENDED PURPOSE.
All modifications or changes not explicitly described or
approved of in this manual could void your Warranty.
WARNING: Basic safety precautions must and should
always be followed to reduce the risk of personal injury.
ON SAFETY
Should any solid object fall on or into the Processing Unit or should
liquid penetrate the Processing Unit, unplug the CatGenie and have
it checked by qualified personnel before using.
Unplug the CatGenie Electric Cord from the outlet before
attempting to clear a jam or remove an object from the Hopper’s
processing area. Do NOT put fingers or hands into the Hopper
opening while the CatGenie is operating.
ON POWER SOURCES
Before operating the CatGenie, check that your local power
supply is identical to the CatGenie operating voltage, which is
120VAC. See complete specifications in Gray Box on right.
UNPLUG the CatGenie FROM ITS ELECTRIC OUTLET before
cleaning the Processing Unit or washing any other CatGenie parts.
NOTE: When you remove the Processing Unit from its Base,
current is still going to it, so unplug the Genie Electric Cord first.
If you are not going to use the CatGenie for an extended
period of time, disconnect the CatGenie from the electric outlet.
When disconnecting the CatGenie electric power cord, pull
the PLUG. NEVER pull the cord. A damaged or defective AC
power cord should be changed at a qualified service shop.
ON PLACEMENT
Position the CatGenie in a place with adequate ventilation to
prevent heat build-up and to prolong the life of the CatGenie.
Do NOT place CatGenie near heat sources, or in a place
subject to direct sunlight, excessive dust, or mechanical shock.
Do NOT place anything on top of or behind the unit.
This may block ventilation holes and cause malfunction.
Do NOT install or store the CatGenie where it could be
exposed to rain or splashing water.
See the Simple Setup Guide for site selection options.
ON OPERATION
Before connecting the CatGenie to the power source, be sure
to read this manual. NEVER, under any circumstances, connect
the CatGenie to a power source unless the CatGenie Processing
Unit is properly seated and secure in its slot in the Base.
Do NOT operate CatGenie with wet hands. Follow all
instructions and warnings in all CatGenie Manuals.
ON CLEANING
Clean the Processing Unit and Control Panel only with a soft
damp cloth slightly moistened with water. NEVER immerse it in
or spray it with water.
Do NOT use any type of abrasive pad, scouring powder
or solvent such as alcohol or benzene. See Cleaning the
CatGenie on page 16 for further instructions.
If you have any questions or problems concerning your
CatGenie, please contact our technical support staff at:
1-888-735-3927
PetNovations, Inc. cannot assume responsibility for any and
all possible damage if CatGenie is inappropriately operated
or used for a purpose other than that for which it is intended.
While PetNovations, Inc. reserves the right to change design
and specifications without notice, we do alert our customers
about upgrades and product improvements.
To receive news of upgrades, improvements, and
special offers, register your Warranty at... catGenie.com
CatGenie SPECIFICATIONS
for NORTH AMERICA
• Power Requirements: 120VAC, 60Hz (15A Fused)
• Power Consumption: 20W (Cleaning Cycle-17Minutes)
1200W (Drying Cycle-17 Minutes)
• Approximate Weight: Total CatGenie: 25 lbs.
(Includes Processing Unit, 11 lbs. Base Unit, 14 lbs)
• Supplied Accessories: Utility or Laundry Room
T-Adapter, Bathroom or Powder Room T-Adapter,
SaniSolution Cartridge, and Washable Granules.
2
www.catGenie.com
1-888-735-3927