120 Self-Flushing Self Washing Cat Litter Box - Manual Operation

13
www.catGenie.com
1-888-735-3927
SOMETHING IS BLOCKING THE REAR VENTS OR FRONT BLOWER. CAUTION. Fire Hazard. Remove anything that blocks air
intake vents on back of Processing Unit. Move the CatGenie 2 inches away from wall. Remove obstructions in the Bowl that block dryer’s
hot airflow. Vacuum rear vents. Let Unit cool for 20 minutes. Press Start Button for 4 seconds. Drying should resume.
CAUTION: Stay with your CatGenie to make sure it’s is OK. If an Error alerts again, you smell burning, see sparks, or anything
abnormal, unplug immediately and contact Customer Service. Call 1-888-SELF-WASH ( 1-888-735-3927 ) Report Error #4. Have Serial #.
ERROR 4. Hear Beeps. Error LED & LED 4 lit. Dryer Overheats or Stops and Starts.
ERROR 3. Hear Beeps. Error LED & LED 3 lit. Cycle Complete. CatGenie is not draining.
CAUTION: Before fixing, feel whether the Washable Granules are WET, DAMP or DRY.
Follow A, if Granules are DRY
•
Follow B, if Granules are WET or DAMP
A: GRANULES ARE DRY but not washed.
CAUSE:
Cycle ran without water because the Water Sensor is crusted with lime.
It reads the lime deposit as if it was water.
Simple Solution: Remove Processing Unit. Pull the Sensor ends up from the top of the Brim. Use a soft cloth
soaked in lemon juice or your finger tips to remove the lime. The TIP must shine. Carefully replace the
Water Sensor securely into its slot
. Then replace the Processing Unit. Press the Start Button to run a special,
regular Cycle where the GenieHand goes into a SUPER SHAKE mode to prevent a Granule clog.
B: GRANULES ARE WET or DAMP. Water has not drained from CatGenie.
CAUSE: Could be plumbing setup OR something stopped the draining.
•
For complete draining, the Genie DrainHose or Hook must NOT be pinched, squeezed, or tightly bent.
Make sure the Base of the CatGenie is NOT sitting on the DrainHose. Hose should pass through one of
the notches in back of the Genie Base.
Part or most DrainHose should be coiled loosely under the Base. No sharp bends!
Add lifts or “feet” to the toilet seat bottom so the seat does NOT squash the Hook. (See Photo).
See page 10 for fitting a Washing Machine Hose and GenieHose into the laundry or utility room drain pipe.
•
Make sure that the Genie DrainHose is not too high. Best if the GenieHose drains into a pipe that is
no more than 4 feet above the floor. If the drain is higher and you have draining problems, raise the CatGenie.
NEXT STEP: clear the unit of the clog that resulted from a setup
situation or from some other source. For example...
•
A toy, some other foreign object, or cat hair on the Impeller Shaft could stop draining
•
Granules under the Hopper have misaligned Hopper and DrainHose connection
•
Granules, dirt, or a small object could be blocking the Hopper Drain Holes
•
Hopper’s Red Washer is defective, squeezed, missing, or misaligned
SOLUTION: FOLLOW STEPS ON PAGE 17
SUPER TERRIFIC TIP:
Clogging is often caused by not running the CatGenie
often enough. Try Cat Activation Mode. CatGenie runs better and extends SaniSolution.
See page 7 for programming.
SUPER TIP:
To keep your CatGenie running smoothly and to prevent
clogs and draining problems, use the CatGenie Machine Maintenance Products
4 to 6 times a year. You received a sample in your CatGenie package. Treatments
come in a Maintenance Solution Cartridge or a Powder in a Pouch.
TIP:
Call 1-888-SELF-WASH ( 1-888-735-3927 ) Report Error #3 and Dry or Wet
Granules. CatGenie tech experts can guide you through the correction process.
Have your Serial #.
Best if
DrainHose
goes into a
drain that’s
less than
4 feet
above
floor
This is WRONG.
Sharp bends
put stress on
the Hose.
Toilet seat “feet” prevent
a squashed Hook