Instructions Manual C49R Cat® Auto Ride-On Sweeper, 49" Cleaning Path Model 641748 AVAILABLE EXCLUSIVELY AT GLOBAL INDUSTRIAL GLOBALINDUSTRIAL.
C49R Model 641748 WARNINGS PLEASE READ THE INSTRUCTIONS CAREFULLY PRIOR TO USING THIS PRODUCT. WARNING - to reduce the risk of fire, electrical shock, and/or injury/damage to persons or property: • • • • • • • • • • • • • • DO NOT operate the machine unless trained and authorized Keep batteries away from sparks and fire at all times. Batteries emit hydrogen gas which is explosive and flammable.
C49R Model 641748 TECHNICAL SPECIFICATIONS Clean width 49” Center brush width 27.5" Side brush width 15.4" Forward speed 0-6.5 MPH Work Capacity 24,000 sq.ft/hr Maximum Surface Incline/Decline 18% Drive motor 24V/800W Roller brush motor 24V/600W Dust collection motor 24V/380W Dust shaker motor 24V/100W Ride motor 2×24V/100W Water tank capacity 7.9 gallon Dust tank capacity 26.4 gallon Filter size 7.5" x7.5" x14.5" Machine Dimensions (L x W x H) 54.9" x 39.8" x 47.
C49R Model 641748 MACHINE COMPONENTS Steering wheel Seat Side brush handle Water tank Roller brush handle Warning light Body housing Steering gear housing Steering gear front cover Wheel Accelerator pedal Dust Pan Foot Lever Side brush sprayer Warning light Water tank cap Fan air outlet Body latch Dust Pan Foot Lever Dust collection box latch Dust collection box Wheel of dust collection box 3
C49R Model 641748 Power display meter Spray switch Roller Brush switch Scram button Key switch Dust collection switch Side Brush switch Dust shaker switch Forward/backward switch Side Brush Handle Roller Brush Handle 4
C49R Model 641748 MACHINE SET UP Package Contents: Jumper cable 1. Machine 2. Battery 3. Charger Machine Set-up/Operation Prior to each use 1) Ensure the 24V battery is connected 2) Ensure the working surface can support the weight of the machine Connecting the batteries 1. Connect the batteries in series using the jumper cables to the positive “+” and negative “-“ end. 2. Connect the red battery connector cable to the positive terminal pole “+” and the black cable to the negative terminal pole “-“.
C49R Model 641748 Filling Water Tank Unscrew the water tank cap and fill with clean water. Adjustment of side brush height The height of the side brushes must be adjusted according to the wear status of the side brushes. Please perform the following steps to adjust: 1. Loosen the hex nut (A) on the adjustment knob. 2. Rotate the adjustment knob (B) clockwise to increase the height of roller brush from the ground. Rotate counterclockwise to reduce the height of roller brush from the ground. 3.
C49R Model 641748 Operation Instructions 1. User must remain seated during operation. 2. Turn the key of the key switch to the "ON" position. The power meter on the control panel will light up. 3. The machine is equipped with an electronic drive control system. a. To move the machine forward, push the directional switch forward and step on the accelerator pedal. b. To move the machine backward, push the directional switch backward and push down on the accelerator pedal. c.
C49R Model 641748 Post Operation Perform the below steps after operating the machine and before storing: 1. Release the accelerator pedal, turn off the brush, dust collection and spray buttons. Wait for the machine motors to stop. 2. Rotate the roller brush handle (on the right side) counterclockwise to lift the roller brush. Rotate the side brush handle (on the left side) clockwise to lift the side brush. 3. Move the machine to the designated area for dumping garbage.
C49R Model 641748 2. If you feel a significant decline in suction after a period of time and the machine improves by using the dust shaking function, remove all six filter cartridges and clean them by using compressed air until dust is no longer escaping from the cartridge. Once complete, mount all six cartridges back to their original location. Cleaning Dust Box 1. After each operation, move the machine to a designated garbage area. 2. Remove the dust box and empty the garbage.
C49R Model 641748 Replacing Roller Brushes Remove the two bolts located on the left side panel Remove screw (A), remove nut (B), and remove the cover. B A Remove the nut, spring, and the dust rubber. Then pull out the roller brush. Spring Dust rubber Replace the roller brush and repeat the above steps in reverse order.
C49R Model 641748 Replacing Side Brushes 1. Remove the bolt at the bottom of the side brush 2. Remove these 3 bolts at the top of the side brush. 3. Replace the side brush and repeat the above steps in reverse order.
C49R Model 641748 Replacing Filters 1. Open the water tank, remove these 4bolts, then remove the mounting plate Mounting Plate 2. Replace the six filters and repeat the steps in reverse order. 3.
C49R Model 641748 TROUBLESHOOTING PROBLEM Machine won’t turn on Little to no water from water spray Floor is not getting clean Vacuum motor does not work Solution 1. Check if there is power in the battery 2. Make sure the machine connection plug is connected to the battery connection plug. 3. Check if the key switch is in the "ON" position. 4. Check if the first fuse in the fuse box is blown. 1. Check if there is water in the water tank. 2. Check if the solenoid valve or water pump is normally open. 3.
C49R Side brush does not turn Model 641748 1. Check if the corresponding contactor of the side brush plate motor can work normally. 2. Check if the fourth fuse in the fuse box is blown. 3.
C49R Model 641748 GLOBAL EQUIPMENT COMPANY INC. FLOOR CARE EQUIPMENT WARRANTY 1. LIMITED WARRANTY Global Equipment Company Inc.
C49R Model 641748 damage or loss is caused by poor or inadequate packaging by Global; or (v) products purchased or transported or exported outside the continental United States or Canada. For the avoidance of doubt, this Limited Warranty shall be null and void for any product exported or transported outside the continental United States and Canada.
GLOBALINDUSTRIAL.COM 1-800-645-1232 © 2021 Caterpillar. All rights reserved. CAT, CATERPILLAR, LET’S DO THE WORK, their respective logos, “Caterpillar Yellow”, the “Power Edge” and Cat “Modern Hex” trade dress as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission. Global Industrial™ a licensee of Caterpillar Inc.
