Instructions / Assembly

Hammock Combo
Congratulations on purchasing this Hammock Combo, with hammock, stand, pad
and pillow! You’re going to love the quality, durability and simple assembly! QUESTIONS
REGARDING THIS PRODUCT? Call our customer-service line toll-free at [phone].
Weight limit: 350 pounds
Your box should contain:
1 - Rope hammock
with chain assembly
1 - Fabric hammock pad
1 - Hammock pillow
1 - Hammock stand, unassembled:
2 - Bolt hooks and nuts
2 - Welded foot poles
2 - 60-inch arm poles
1 - 51-inch center pole
2 - Round protective pole caps *
round protective pole caps
* For your convenience,
round protective pole
caps are already tted
into their respective poles.
Before beginning assembly,
make sure you have all parts.
STEP 1. Place one foot pole at on the ground with the small, curved pipe facing upward, lin-
ing up the end of the curved pipe opposite the weld to one end of your center pole. (FIGURE
1). Depress the steel pin on the narrower pole, then slide the wider pole over the narrower
pole (FIGURE 2) until the pin clears the lip of the wider pole and pops out the hole (FIGURE 3).
Repeat this step with the opposite end of the center pole and the remaining foot pole to cre-
ate the stand’s base.
WARRANTY | Products guaranteed free of defects in workmanship and materials for up to one year from date of purchase. If an item is found to be defec-
tive within that time, manufacturer The HammockSource will replace it at no charge. Normal wear and tear, including prolonged exposure to snow, rain and
heavy humidity, is not covered, nor is mold, mildew or damage from improper storage, maintenance or installation. An original sales receipt must accompany
any returned product, along with a Return Authorization Number from HammockSource customer service; call toll-free at [phone].
022310
weld
FIGURE 1
FIGURE 3
FIGURE 2
STEP 4. Using the spring pin,
attach the uncapped end of
one arm pole to the remain-
ing curved pipe of one foot
pole. (FIGURE 4). Repeat with
other foot and arm poles.
FIGURE 4
STEP 3. Remove the attached
nut from one bolt hook, insert-
ing the hook into the hole near
the capped top of one stand
arm (FIGURE 5), the threaded
end of the bolt coming out the
corresponding hole at the back
of the pole. Loosely attach the
nut to the hook’s threaded end,
using your wrench to tighten
(FIGURE 6); do not overtighten.
Unroll the hammock and at-
tach a link of chain at each
end to the bolt hooks now
tted to each stand arm
(FIGURE 7); adjust chain lengths
to change your hammock
height. Hammock ropes will
stretch the rst few times
the hammock is used; once
they’ve stretched completely,
readjust the hammock-chain
links to achieve your most
comfortable hanging height.
Hammock care and safety tips, see reverse side >>>>>>>>>>>>>>>
STEP 4. Loosely center the unfolded
hammock pad atop the hammock,
with the pad’s tie-on straps under-
neath. Using a simple knot, tie the
straps at both ends of the pad to the
wooden spreader bars at each end
of the hammock (FIGURE 8), then tie
the straps at the pad’s middle to the
rope braid running along the ham-
mock’s side (FIGURE 9). If you don’t like
the ends of the straps hanging down,
you can tuck them underneath the
pad itself.
STEP 5. Center the hammock pillow
at one end of your hammock pad.
Using a simple knot, attach the two
sets of ties to the hammock spreader
bars beneath the pad (FIGURE 10).
Tuck the strap ends beneath the pad
if you don’t like them dangling.
>>>>>>>>>>>>>>> Assembly instructions
FIGURE 8
FIGURE 9
FIGURE 10
Tools you’ll need:
13 mm wrench,
or adjustable wrench
FIGURE 6
FIGURE 5
FIGURE 7