Model：CD-K010 INSTALLATION GUIDE IMPORTANT SAFEGUARDS READ ALL INSTRUCTIONS BEFORE USING. Get free technical support for the lifetime of your product. Email: service@castadivahome.
Table of Contents Table of Contents 1 Safety Information 2 Pre-installation 7 Parts diagram 7 Tools required 7 Hardware Included 8 Technical specifications 9 Installation 10 Operation 14 Care and Cleaning 18 Troubleshooting 20
Safety Information When using the electronic product, especially in the presence of children, basic safety precautions should always be followed, including the following. Please read all instructions before use. DANGER-Reduce the risk of electric shock 1.Do not use while bathing. 2.Do not place or store the product where it may fall or be dragged into a bathtub or sink. 3.Do not place in or drop into water or other liquid. 4.
Safety Information ISED Warning statements in User Manual This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
Safety Information Precautions before use In order to avoid personal injury and property damage to users and other people, please read the following safety precautions carefully and strictly observe them. After reading, please keep this manual in a drawer where you can access easily. ☆Do not touch the power plug with wet hand, otherwise it may cause electric shock. ☆It is strictly forbidden to put the electrified product on its side or upside-down, otherwise it may cause fire or burn down.
Safety Information ☆Do not use banana oil, gasoline, liquid medicine and detergent, insecticide and hard brush to clean this product. Toilet cleaner may only be used for ceramic body. ☆Do not use this product in rooms with humidity more than 90% RH, the use environment should have a dry and wet separation, such as installing shower room or shower curtain. ☆For the newly decorated house, the residual mud and sand in the pipeline are easy to damage the machine and affect human health.
Safety Information Grounding instructions This product should be grounded. In the case of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape path for the current. This product is equipped with a power cord with a ground wire and a properly grounded plug. The plug must be plugged into a properly installed and grounded socket.
Pre-installation Parts diagram Lid rubber pad Lid Remote control Power plug Remote control holder Trim cover Flushing/Stop button Trim strip Heated seat Seat sensor Angle stop Nozzle Rear /Front cleansing button Ceramic Foot sensor Decorative cap Tools required ＋ Marking pen Tape Adjustable wrench Electric drill (including 4.
Pre-installation Hardware Included INSTALLATION GUIDE IMPORTANT SAFEGUARDS Model：CD-K010 Get free technical support for the lifetime of your product. READ ALL INSTRUCTIONS BEFORE USING. Email: service@castadivahome.com Phone: 1-209 389 9799 ≥12in Drain outlet Align cardboard with the centerline of drain outlet， D Shim Nut Mounting bracket Assemble the mounting bracket with bolts and then install them to the pre-installed flange plate on the ground and lock tight with nuts.
Pre-installation Technical specifications Rear washing Night light Front washing Remote controller Auto washing Rated voltage Cleans- Oscillating ing Water pressure adj. Water temp. adj. Nozzle position adj. Rated frequency 5 level Rated power 5 level+Off Ambient temp. 5 level 120V~ 60Hz 1000W 32℉~104℉ Pressure of Water supply 30psi~80psi(Static pressure) Warm dry Flow of Water supply ≥25L/min 37.4℉~95℉ Fresh air Seat and Cover Dry temp. adj. 3 level+Room temp.
Installation Suggestions on power line and water supply connection 485mm/19.09in 410mm/16.14in 390mm/15.35in Technical drawings and power cord connections suggestions 700mm/27.56in Rough-in 305mm/12in 500mm/19.69in NOTE: It is necessary to install the provided angle stop in an 78in /13. mm 350 accessiable area for quick shutoff in case of an emergency. 150mm/5.9in The power socket can be installed on either left or right. in 5.75 m/1 m 400 in 7.
Installation 2.Install Toilet and Toilet Wax Ring( For Option B installation, please see template.) Fixing bolt Flange plate Install the flange plate. Position correctly the two fixing bolts of the flange. D Nut Shim Mounting bracket Wax ring Assemble the mounting bracket with bolts and then install them to the pre-installed flange plate on the ground and lock tight with nuts. Insert the wax ring under the toilet.
Installation 3.Install the Water Supply Hose As shown in the figure, install water supply line to angle stop. Large end facing ball valve E-bidet brai ded h ose 1) If the water inlet pressure is greater than 30psi, please install the flow limiting plate in the angle stop; 2) Only use the accessory parts that are shipped with the product for installation; 3) After installation,check water seal and turn on the power supply. Water leakage shall be avoided. A A B Water Su p pl y Li ne 4.
Installation Open the angle stop Connecting remote control Power on GROUNDED OUTLET GROUNDING PIN GROUNDED OUTLET BOX Connecting Remote Control Long press the remote control stop button, the first, third Long press the stop button and fifth LED lights start flickering indicating the remote Power on GROUNDED OUTLET control connection is ready. Then release the remote control stop button and power on the smart toilet.
Operation Side button description Side button definition Side button function When sitting, press Automatic rear cleansing button to start automatic rear cleansing function. 15 seconds of rear cleaning at fixed position→30 seconds of oscillate cleaning→rear cleaning at fixed position then stop (An auto cleansing cycle is about 60 seconds from start to stop), and the wand automatic retract →120 seconds of drying. Press When sitting, press button to end the cycle at any time.
Operation Remote control instructions ● Rear cleansing/Front cleansing When sitting, press button or button, enter the rear cleansing or front cleansing mode, press the button again to enter the oscillated cleansing mode. The cleansing cycle which stops automatically after 3 minutes; or press button to stop the cleansing function. ● ECO function Long press button, turn on/off ECO function, when ECO function is on, the seat temp. will decrease slowly after leaving the seat then keep at 82.4℉±5.4℉.
Operation ● Flush function setting Short press button to turn on flush function. Long press button to turn on or off automatic flushing function. After sitting for more than 3 seconds the toilet will detect the user. Then the toilet will auto flush approximately 6 seconds after leaving the seat. ● Lid/seat opening and closing Press button to open or close the lid; press button to open or close the seat.
Operation Note 1. When the automatic open and close function of the product is turned on, the product can identify the person moving within a certain distance from the ceramic front. This process is called microwave motion induction;When the On Off Sensor range product recognizes that the person is moving within the microwave induction distance, the lid will not automatically turn off.
Care and Cleaning Cleansing filter screen Pull power plug off and turn off the water supply Close unscrew the plug and remove the filter screen.
Care and Cleaning Long time non-use processing mode Step 1: When not in use, turn off water Step 2: Pull the plug out, loosen the braided supply,long press hoses, drain out the inside water. button to enter self cleansing mode. Move to step2 after self cleansing completed. Pull out the power supply A A Turn off water supply Close Cleaning and maintenance Cleaning the Cover & Seat: Cleaning the ceramic: Turn off the water supply, pull out the power plug.
Troubleshooting Troubleshooting Frequently asked questions. (FAQ) Please read the following questions carefully, and refer to the instructions. If the product still does not work contact your local sales dealer or contact the manufacturer. Tips: If there is water leakage, immediately turn off the water supply and pull the power plug. The following reasons may cause product's malfunction. 1.
Troubleshooting Issue Heated Seat Cause Solution Seat temperature is not warm enough during usage. Is seat temperature set to“off” or on the lowest setting? Reset the seat temperature to a higher setting. Seat temperature is too hot Is seat temperature set on the highest setting? Reset the seat temperature to a lower setting. Night Light Off Night light is set on “off” status. Long press the “Night Light” button to turn on the light. Night Light On Night light is set on “on” status.
Get free technical support for the lifetime of your product. Email: service@castadivahome.
