User Manual
Table Of Contents
- Contents
- Safety Precautions
- Operating Precautions
- Getting Ready
- Unpacking
- Operation Flow to Projection
- General Guide
- Key and Indicator Panel
- Back Terminals
- Placing the Projector on a Desk or on the Floor
- Connecting with Another Device
- Connecting a Computer
- Connecting to a Video Device
- Outputting Audio from the Projector to Another Device
- Connecting a Microphone (XJ-UT Series, XJ-F21XN, XJ-F211WN, XJ-S400UN, XJ-S400WN)
- Connecting to a Network with a LAN Cable (Network Models Only)
- Connecting a Wireless Adapter (Network Models Only)
- LOGO Terminal (Firmware Updates, User Logo Transfers)
- Connecting a Scientific Calculator (Network Models Only)
- SERIAL Terminal (Projector Control Using Commands)
- USB Power
- Cover Included with the YW-41 Wireless Adapter
- Attaching and Removing the Cable Cover (XJ-UT Series)
- Remote Controller
- Operating the Projector
- Turning the Projector On or Off
- Selecting an Input Source (INPUT)
- Using Auto Projection Off
- Basic Image and Audio Operations During Projection
- Flipping the Projected Image Horizontally (Mirror Mode)
- Light Control
- Digital Screen Shift
- Projecting a Template
- Test Pattern Projection
- Control Panel Lock
- Configuring Remote Control ID and Projector ID Settings
- Using the Countdown Timer (TIMER)
- Using the Presentation Timer (TIMER)
- Using the Setup Menu (MENU)
- Using a Password
- Cleaning the Projector
- Troubleshooting
- Appendix
- Supplying USB Power to Another Device
- Mounting the Projector on a Wall (XJ-UT Series)
- Hanging the Projector from a Ceiling
- Using the MONITOR OUT Terminal (XJ-UT Series, XJ-S400UN, XJ-S400WN)
- Projection Distance and Screen Size
- Aspect Ratio Setting and Projection Image
- Supported Signals
- Projector RS-232C Control
- Specifications
70
Troubleshooting
The color and on/off/flashing status of the indicators let you know the current operational status of the
projector. The table below shows what the indicators look like when operation is normal.
Note
The POWER/STANDBY indicator will flash green if the projector is turned on but the projection
light has been turned off by Auto Projection Off (page 47).
Normal Operation Indicators
■ : Lit ★ : Flashing
When the indicators appear like this:
It means this:
XJ-UT Series
XJ-F Series
XJ-S Series
POWER/
STANDBY
LIGHT TEMP
POWER/
STANDBY
STATUS
The projector has just been plugged into a power
outlet. Wait until the projector enters the standby state
(see below) before trying to turn on power.
■■■■■
Red Amber Amber Amber Amber
■■
Standby state: The AC power cord is plugged in and
the projector is in standby.
Red Red
XJ-UT312WN/XJ-UT352WN
XJ-F21XN/XJ-F211WN/
XJ-S400UN/XJ-S400WN
Projector is warming up after being turned on.
★■■★■
Green Amber Amber Green Amber
XJ-UT352W
XJ-F11X/XJ-F101W/
XJ-S400U/XJ-S400W
★■ ★■
Green Green Green Green
■■ ■■
Projector is on and standing by for use.
“On” is selected for the projector’s “Light Control”
setting.
Green Green Green Green
■■
Projector is on and standing by for use.
“Off” is selected for the projector’s “Light Control”
setting.
Green Green
★ 3 ■■ ■★ 3 ■■
Projector is performing an internal process to prepare
for network system startup (network models only).
Green Amber Amber Green Amber
★★
Projector is performing internal power down processes.
Red Red