User Manual
Table Of Contents
- Contents
- Safety Precautions
- Operating Precautions
- Getting Ready
- Unpacking
- Operation Flow to Projection
- General Guide
- Key and Indicator Panel
- Back Terminals
- Placing the Projector on a Desk or on the Floor
- Connecting with Another Device
- Connecting a Computer
- Connecting to a Video Device
- Outputting Audio from the Projector to Another Device
- Connecting a Microphone (XJ-UT Series, XJ-F21XN, XJ-F211WN, XJ-S400UN, XJ-S400WN)
- Connecting to a Network with a LAN Cable (Network Models Only)
- Connecting a Wireless Adapter (Network Models Only)
- LOGO Terminal (Firmware Updates, User Logo Transfers)
- Connecting a Scientific Calculator (Network Models Only)
- SERIAL Terminal (Projector Control Using Commands)
- USB Power
- Cover Included with the YW-41 Wireless Adapter
- Attaching and Removing the Cable Cover (XJ-UT Series)
- Remote Controller
- Operating the Projector
- Turning the Projector On or Off
- Selecting an Input Source (INPUT)
- Using Auto Projection Off
- Basic Image and Audio Operations During Projection
- Flipping the Projected Image Horizontally (Mirror Mode)
- Light Control
- Digital Screen Shift
- Projecting a Template
- Test Pattern Projection
- Control Panel Lock
- Configuring Remote Control ID and Projector ID Settings
- Using the Countdown Timer (TIMER)
- Using the Presentation Timer (TIMER)
- Using the Setup Menu (MENU)
- Using a Password
- Cleaning the Projector
- Troubleshooting
- Appendix
- Supplying USB Power to Another Device
- Mounting the Projector on a Wall (XJ-UT Series)
- Hanging the Projector from a Ceiling
- Using the MONITOR OUT Terminal (XJ-UT Series, XJ-S400UN, XJ-S400WN)
- Projection Distance and Screen Size
- Aspect Ratio Setting and Projection Image
- Supported Signals
- Projector RS-232C Control
- Specifications
66
Network Settings*
1
3
Network Settings 3
Wireless LAN Function
Toggle the projector’s wireless LAN function between “Enable”* and “Disable”.
Network Settings*
1
3
Network Settings 3
Remote On
Specify whether the projector can be turned on via wired LAN while the projector is
in standby (projector off with power being supplied).
Enable: Remote on enabled.
Disable*: Remote on disabled.
Projector standby power consumption depends on whether or not “Remote On” is
enabled. For information about power consumption in each standby state, see
“Specifications” (page 88).
Network Settings*
1
3
Network Settings 3
PJLink Authentication
Enable or disable PJLink connection authentication. Initial default setting: Enable.
Network Settings*
1
3
Network Settings 3
Update Network Settings
Apply changes to the “Network Settings 3 Network Settings” menu items to
projector settings.
Network Settings*
1
3
Network Settings 3
Initialize Network Settings
Return network settings to their initial factory defaults.
Operational Info Display the projector information below.
Input Signal, Signal Name, Resolution, Horizontal Frequency, Vertical Frequency,
Scan System, Audio Input, Projector ID, Light Time, Version (projector ROM version),
Board Number (unique board number of each product)
Restore All Defaults 3
Unit Operating Time
Display the cumulative operating time of this unit.
This time cannot be initialized.
Restore All Defaults 3
Restore All Defaults
Initialize all Setup Menu item settings, except for those below.
Language, Power On Password, Network Setting Password, Network Settings, Light
Time, Unit Operating Time
Note
A user logo image that has been transferred to the projector (page 36) is not
deleted by a “Restore All Defaults” operation.
*1 For details about how to configure the settings of the “Network Settings” menu items, refer to the
separate “Network Function Guide”.
Use this menu item: To do this:
N