User Manual
Table Of Contents
- Contents
- Safety Precautions
- Operating Precautions
- Getting Ready
- Unpacking
- Operation Flow to Projection
- General Guide
- Key and Indicator Panel
- Back Terminals
- Placing the Projector on a Desk or on the Floor
- Connecting with Another Device
- Connecting a Computer
- Connecting to a Video Device
- Outputting Audio from the Projector to Another Device
- Connecting a Microphone (XJ-UT Series, XJ-F21XN, XJ-F211WN, XJ-S400UN, XJ-S400WN)
- Connecting to a Network with a LAN Cable (Network Models Only)
- Connecting a Wireless Adapter (Network Models Only)
- LOGO Terminal (Firmware Updates, User Logo Transfers)
- Connecting a Scientific Calculator (Network Models Only)
- SERIAL Terminal (Projector Control Using Commands)
- USB Power
- Cover Included with the YW-41 Wireless Adapter
- Attaching and Removing the Cable Cover (XJ-UT Series)
- Remote Controller
- Operating the Projector
- Turning the Projector On or Off
- Selecting an Input Source (INPUT)
- Using Auto Projection Off
- Basic Image and Audio Operations During Projection
- Flipping the Projected Image Horizontally (Mirror Mode)
- Light Control
- Digital Screen Shift
- Projecting a Template
- Test Pattern Projection
- Control Panel Lock
- Configuring Remote Control ID and Projector ID Settings
- Using the Countdown Timer (TIMER)
- Using the Presentation Timer (TIMER)
- Using the Setup Menu (MENU)
- Using a Password
- Cleaning the Projector
- Troubleshooting
- Appendix
- Supplying USB Power to Another Device
- Mounting the Projector on a Wall (XJ-UT Series)
- Hanging the Projector from a Ceiling
- Using the MONITOR OUT Terminal (XJ-UT Series, XJ-S400UN, XJ-S400WN)
- Projection Distance and Screen Size
- Aspect Ratio Setting and Projection Image
- Supported Signals
- Projector RS-232C Control
- Specifications
54
4.
To stop template projection, change to another input source or turn off the
projector.
Note
Note that an image input signal being input to the projector cannot be projected while a
template is being projected.
Auto Projection Off (page 47) and Auto Power Off (page 64) are both disabled while a template
is being projected.
With an XJ-UT352W, XJ-F11X, XJ-F101W, XJ-S400U, and XJ-S400W model, the following
settings cannot be adjusted while a template is being projected: “Brightness” (page 60),
“Contrast” (page 60).
To change the template type (XJ-UT352W, XJ-F11X, XJ-F101W,
XJ-S400U, XJ-S400W)
1.
While a template is being projected, press the [FUNC] key and then the [ENTER]
key.
This displays the “Template Type” menu.
2.
Use the [] and [] keys to select the template you want to project, and then
press the [ENTER] key.
To change the template type (Network Models)
1.
While a template is being projected, press the [FUNC] key and then the [ENTER]
key.
This displays the template selection screen.
2.
Use the cursor keys to move the focus to the template you want to project.
To project a template that is located in a folder that is different from the currently displayed
folder, perform the steps below.
(1) While the focus is located at the upper left template, press the [] key.
This moves the focus to the folder selection area.
(2) Use the [] and [] keys to move the focus to the folder that contains the template you
want to project.
(3) Press the [] key.
This moves the focus back to the template selection area.
(4) Use the cursor keys to move the focus to the template you want to project.
3.
Press the [ENTER] key.
Note
Under network model initial default settings, only the top folder contains templates. All of the
other folders are empty. For information about the procedure to add a template, refer to the
separate “Network Function Guide”.