English ES Español USER’S GUIDE GUÍA DEL USUARIO Please keep all information for future reference. Guarde toda documentación para futuras consultas. Safety Precautions Before trying to use the piano, be sure to read the separate “Safety Precautions”. Precauciones de seguridad Antes de intentar usar el piano, asegúrese de leer las “Precauciones de seguridad” separadas.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. IMPORTANT SAFETY INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
General Guide........................... E-2 Using Registration Memory...E-34 Installing the Music Stand........................................... E-3 PX-3 Configuration ..................................................... E-4 Modes ......................................................................... E-6 Saving Settings and Using Panel Lock....................... E-7 Returning the Digital Piano to Its Factory Default Settings ............................................. E-7 Registration Data ....
General Guide 8 1 2 3 4 5 6 9 7 bl bk bm bn bo bp ∗ bq do br ck bs cl cm bt cn co cp cs ct cq cr dk dn dl dm Back dp dq dr Left Side ds dt ek Bottom en el E-2 em
General Guide VOLUME knob CLAVI/VIBES, 4 button ZONE SELECTOR (LOWER 1), REPEAT button ORGAN, 5 button ZONE SELECTOR (LOWER 2), sREW button STRINGS/ENSEMBLE, 6 button ZONE SELECTOR (UPPER 1), dFF button GUITAR/BASS, 7 button ZONE SELECTOR (UPPER 2), PAUSE button OTHERS/GM, 8 button INT/EXT, PLAY/STOP button LAYER, EXIT button ZONE EDIT, PAGE, PART button SPLIT, u button ASSIGNABLE 1 button REVERB, i button ASSIGNABLE 2 button CHORUS, ENTER butto
General Guide PX-3 Configuration Master Control Configuration The PX-3 Digital Piano is a MIDI master keyboard that uses four zones (UPPER 1, UPPER 2, LOWER 1, LOWER 2) to control the internal sound source (INT) and external MIDI devices (EXT). Each zone performs simultaneous control over one internal sound source part and one external MIDI device channel (when both INT and EXT are ON). The target (INT/EXT) of each zone control can be turned on or off as desired using the (INT/EXT) button.
General Guide Sound Source Configuration English The sound source is configured with a total of 36 parts: four parts that correspond to each of the zones, 16 parts for MIDI file playback, and 16 parts that operate as the multi-timbre sound source during receipt of MIDI input. The following shows the relationships between parts, ports, and MIDI channels.
General Guide Modes This Digital Piano has two main modes: a MASTER CONTROL mode and a CARD PLAYER mode. Each of these modes has two sub-modes: a TONE mode and a REGISTRATION mode. MASTER CONTROL mode CARD PLAYER mode TONE mode TONE mode REGISTRATION mode REGISTRATION mode Use the MASTER CONTROL mode when playing the Digital Piano in a stand-alone configuration or when using it as a MIDI master keyboard.
General Guide English Saving Settings and Using Panel Lock Your Digital Piano lets you save its current settings, and lock its buttons to protect against operation errors. For details, see “Backup” and “Panel Lock” (page E-40). Returning the Digital Piano to Its Factory Default Settings Perform the following procedure when you want to return the Digital Piano’s stored data and settings to their initial factory defaults. 1. 2. Turn off the Digital Piano.
Power Outlet Your Digital Piano runs on standard household power. Be sure to turn off power whenever you are not using the Digital Piano. Using an AC Adaptor Use only the AC adaptor (JEITA Standard, with unified polarity plug) that comes with this Digital Piano. Use of a different type of AC adaptor can cause malfunction. Specified AC Adaptor: AD-A12150LW • Use the supplied power cord to connect the AC adaptor as shown in the illustration below.
Connections IMPORTANT! • Before connecting headphones, be sure to use the Digital Piano’s (VOLUME) knob to turn the volume down to a low level. After connecting, you can adjust the volume to the level you want. Left Side Commercially available headphones PHONES jacks Damper Pedal Pressing the damper pedal while playing will cause the notes you play to reverberate for a very long time.
Connections Connecting Audio Equipment or an Amplifier This Digital Piano outputs notes from its LINE OUT R (right channel output) and LINE OUT L/MONO (left channel output). Connect a keyboard amplifier or other device to direct output to speakers. You can adjust the LINE OUT volume level with the Digital Piano’s (VOLUME) knob. To input from audio equipment (Figure ) LINE IN R jack input is output from the LINE OUT R jack, and LINE IN L/MONO input is output from LINE OUT L/MONO.
Selecting and Playing a Tone To turn on Digital Piano Power 1. After ensuring that the (POWER) button is in the off position, connect the AC adaptor to the Digital Piano. Listening to Demo Tunes 1. • This starts demo tune play. • The Digital Piano has a total of four demo tunes. You can use the buttons to jump the beginning of the previous (q) or next (w) demo tune. You can use the Tone Group buttons ( to ) to select a specific demo tune.
Selecting and Playing a Tone 5. Check to make sure that the lamp above the (TONE) button is lit. You can configure the keyboard so it plays two different tones at the same time (Layer) or to play different tones in the left and right ranges (Split). You can even use Layer and Split in combination with each other. Lit 6. Layering and Splitting Tones • If it is unlit, press the (TONE) button to light the upper lamp. The following describes the various possible Layer and Split combinations.
Selecting and Playing a Tone 5. • You can select a tone for each zone in both the MASTER CONTROL and CARD PLAYER modes. Note however that some procedures and operations (lamp lighting status) when a tone is selected for each zone in the CARD PLAYER mode are different from those in the case of the MASTER CONTROL mode. Here, explanations are based on selecting a tone for each zone in the MASTER CONTROL mode.
Selecting and Playing a Tone Splitting the Keyboard between Two Tones 8. To cancel the keyboard split, press the (SPLIT) button again so its lamp goes out. NOTE LOWER 1 UPPER 1 1. Use the “Tone List” (page E-57) to look up the group(s) and numbers of the two tones (UPPER 1 zone tone and LOWER 1 zone tone) you want to use. 2. Check to make sure that the both the (LAYER) and (SPLIT) button lamps are unlit.
To use layer and split together LOWER 1 LOWER 2 1. 2. 3. UPPER 1 UPPER 2 Use the “Tone List” (page E-57) to look up the group(s) and numbers of the tones (UPPER 1, UPPER 2, LOWER 1, and LOWER 2 zone tones) you want to use. Check to make sure that the both the (LAYER) and (SPLIT) button lamps are unlit. • If one or both lamps are lit, press the (LAYER) and (SPLIT) buttons to turn them off. 7. Press the (LAYER) button so its lamp is unlit. 8.
Selecting and Playing a Tone 13. To cancel layer and split, press (LAYER) and (SPLIT) buttons again so their lamps go out. NOTE • When using Layer and Split at the same time, you can switch to only a single tone in either of the keyboard ranges by configuring INT OFF for the zone whose tone you do not want to sound. For example, you could perform the steps below to sound zones UPPER 1, UPPER 2, and LOWER 1, without sounding the LOWER 2 zone. UPPER 1 UPPER 2 LOWER 1 1.
Applying Effects to a Tone MASTER CONTROL Your Digital Piano provides four types of reverb and four types of chorus. The reverb and chorus functions have their own dedicated keys for easy on/off operation. • Each press of the (REVERB) button toggles reverb on and off. The lamp above the button is lit when reverb is on, and unlit when it is off. • Each press of the (CHORUS) button toggles chorus on and off. The lamp above the button is lit when chorus is on, and unlit when it is off.
Confirming Common Parameter Settings MASTER CONTROL Common parameters include transpose, bend range, equalizer, and other global parameters. Common parameters also include the settings of the function assigned to the ASSIGNABLE buttons. Common Parameters Operations The common parameter settings appear on the common menu that appears first whenever you turn on the Digital Piano. Page Parameter Name Common menu Settings • The common menu has five pages.
Confirming Common Parameter Settings 1. 5. Check to make sure that the lamp above the (MASTER CONTROL) button is lit. • If it is unlit, press the (MASTER CONTROL) • Pressing w and q at the same time returns the setting to its initial default. • Holding down w or q will scroll through the settings at high speed. • For details about the meaning and range of each parameter setting, see “Common Parameter Settings” (page E-20). button to light it. Lit 6. 2.
Confirming Common Parameter Settings Common Parameter Settings This section explains the meaning of each common parameter, and provides information about their setting ranges and initial default values. • In this section, each parameter is preceded by a number and a letter, like “1-A”. This indicates the common menu page number (1) and the PARAMETER SELECTOR button you need to press to select it (A). • The values following the description of a parameter are its setting range.
Confirming Common Parameter Settings English ■ 2-A to 3-D Band Gain and Frequency Settings Parameter Name Location Description Settings (* indicates default) Low Gain (LoG) 2-A Adjusts the low-range gain. –12 to 0* to 12 Low Freq. (LoF) 2-B Specifies the frequency of the low-range adjusted by Low Gain. 0.2*, 0.4, 0.8 kHz LowMid Gain (LoMdG) 2-C Adjusts the low mid-range gain. –12 to 0* to 12 LowMid Freq. (LoMdF) 2-D Specifies the frequency of the low midrange adjusted by LowMid Gain.
Confirming Common Parameter Settings ■ 4-A Assignable Button 1 Type (Asgn1) Specifies the function assigned to the (ASSIGNABLE 1) button. The following describes the functions that can be assigned by each setting. Setting Assigned Functions Modulation (Mod) This setting assigns modulation to the button.*1 The depth of the modulation is specified using the (B) and (C) buttons. Portamento (Por) This setting assigns portamento the button.
Confirming Common Parameter Settings English ■ 4-B, 4-C, 4-D, 5-B, 5-C, 5-D Settings when Asgn1/Asgn2 = Control Change Number 0 to 127 Parameter Name Location Description Settings (* indicates default) Channel (Ch) 4-B, 5-B Specifies the MIDI channel*1 for sending control changes. 1* to 16 Value (Button OFF) (OfVal) 4-C, 5-C Specifies the value sent when the button is released (turned off).
Using the Assignable Buttons MASTER CONTROL There are two assignable buttons named (ASSIGNABLE 1) and (ASSIGNABLE 2). The (ASSIGNABLE 1) button is designed so it is on while pressed and off while released. The (ASSIGNABLE 2) button toggles on (lamp lit) and off (lamp unlit) each time it is pressed. The main use of the assignable buttons is to perform real-time operations, mainly for effects. You can configure settings for the assignable button with the common menu (page E-18).
Using the Assignable Buttons English By-passing the DSP (ASSIGNABLE 2) While the (ASSIGNABLE 2) button is on, only the sound of a specified zone is output without passing through the DSP. Common Parameter Information: 5-A Assignable Button 2 Type (Asgn2) (page E-22) 5-B Settings when Asgn2 = DSP Bypass (Dbp) (page E-23) NOTE • For more information about DSP bypass, see the flowchart under “Master Control Configuration” (page E-4).
Using the Digital Piano as a MIDI Master Keyboard MASTER CONTROL A unique MIDI channel can be assigned to each of the Digital Piano’s four zones (UPPER 1, UPPER 2, LOWER 1, LOWER 2) to provide simultaneous control of up to four external MIDI devices. IMPORTANT! • This section provides only basic information about how to use the Digital Piano as a MIDI master keyboard.
Using the Digital Piano as a MIDI Master Keyboard After you use the (LAYER) and (SPLIT) buttons to select a zone configuration, you can turn internal sound source control (INT) and external MIDI device control (EXT) on or off as required for each zone. Use the (INT/ EXT) button to specify what a zone controls. To specify what a zone controls 1.
Editing Zone Parameters MASTER CONTROL Your Digital Piano is a four-zone MIDI master keyboard (“Master Control Configuration”, page E-4). A zone is a unit that controls the internal sound source and/or external MIDI device. Just as you can select a different internal sound source tone for each zone, you also can specify a mixer, DSP and other settings for an internal sound source, and you can specify a MIDI channel and other control settings for an external MIDI device.
To change zone parameter settings 1. 5. Check to make sure that the lamp above the (MASTER CONTROL) button is lit. • If it is unlit, press the (MASTER CONTROL) • The lamp of the button you press will light, which indicates its zone is selected. button to light it. Lit 2. 3. 6. Use the (ZONE EDIT) button to display the zone menu page that contains the parameter whose setting you want to change. Example: Zone menu page 2 Use the (EDIT w, q) buttons to change the setting.
Editing Zone Parameters MIDI Settings Zone Parameter Settings This section explains the meaning of each zone parameter, and provides information about their setting ranges and initial default values. • In this section, each parameter is preceded by a number and a letter, like “1-A”. This indicates the common menu page number (1) and the PARAMETER SELECTOR button you need to press to select it (A). • In this section, the name of each zone parameter is followed by INT and/or EXT .
■ 3-C Parameter Value (Value) ■ 5-B Release Time (Relas) This item is used to change the setting of the parameter displayed in 3-B. Release time is the time it takes for the INT / EXT sound to fade when a note ends. Adjustment is relative from the initial default setting (0) of each tone. A larger negative absolute value shortens the release time, while a larger positive value lengthens the release time.
Editing Zone Parameters Effect Settings ■ 6-B Vibrato Depth (VbDpt) This item is for adjusting the depth INT / EXT (strength) of vibrato applied to notes. A larger negative absolute value makes vibrato shallower, while a larger positive value makes it deeper. –64 to 0* to +63 ■ 6-C Vibrato Delay (VbDly) This item is for adjusting the time until INT / EXT vibrato starts to be applied to a note.
Editing Zone Parameters Control Settings English If you are using multiple zones for keyboard play and you want to disable pedal and other controller operations for a particular zone, turn off the settings described in this section for that zone. ■ 8-A Pedal Enables and disables pedal operations. OFF, ON* INT / EXT ■ 8-B Bender (Bend) Enables and disables the (PITCH BEND) wheel operations. OFF, ON* INT / EXT ■ 8-C Assignable 1 (Asgn1) Enables and disables the (ASSIGNABLE 1) button operations.
Using Registration Memory MASTER CONTROL Normally, before playing something you need to set up the Digital Piano by configuring a number of different settings, including layer and split on/off, a tone selection for each zone, equalizer settings, and DSP settings. You can save up to 64 Digital Piano setups (which include control panel and internal settings) to registration memory for later recall when you need them. Each setup is saved as “registration data.
Using Registration Memory ck While holding down the (STORE) button, press one of the number buttons ( (1) through (8)) to specify the number of the area (1 to 8) where you want to save the registration data. cl cm cn co cp cq cr dm • Pressing a number button immediately executes the registration data save operation. • The following shows how the display would appear if you select Bank 1, Area 3. To rename a registration memory bank 1.
Using Registration Memory Saving Registration Memory Bank Data to a File 3. Registration data can be stored to a file in the Digital Piano’s internal memory area or on an SD card. You can store the registration data in a single registration memory bank (eight areas) or the data in all of the registration memory banks (64 areas) to a file. Depending on the type of operation you want to perform, use the (u) and (i) buttons to display one of the screens shown below.
To recall registration memory bank data from a file 1. Depending on where the file is located, perform one of the steps shown below. If the file is located here: Perform this operation: Internal area Remove the SD card from the Digital Piano’s card slot. SD card Insert the SD card into the Digital Piano’s card slot. 2. Press the (REGISTRATION) button so the lamp below it is lit. This is the REGISTRATION mode. 3.
Using the Function Menu MASTER CONTROL The function menu contains global settings (overall tuning and touch adjustment, local control ON/OFF, etc.) that need to be changed by you relatively infrequently. It also includes some SD card operations (format, etc.) Function Menu Operations This section explains operations involving function menu settings. For details about specific function menu items, see “Function Menu Settings” (page E-39). To change the setting of a function menu item 1.
Using the Function Menu 6 Temperament/Effect This section explains the meaning of each function menu parameter, and provides information about their setting ranges and initial default values. • For each item, the initial default setting is indicated by an asterisk (*). Temperament 1 Tuning 00* 01 02 03 04 05 06 07 08 (Tune) Use this item to adjust the pitch in cent steps (1 cent = 1/100 semitone).
Using the Function Menu 7 Playback/Card (Play/CARD) Song MIDI Out (MIDI Out) Select ON* for this item to send MIDI data to an external destination when a Format0 or Format1 SMF file is played back on the Digital Piano. Select OFF to disable send. MIDI data is never sent during playback of a CM2 format file, regardless of what is selected for this setting. Song Volume (SongVol.) Use this item to adjust the volume level for playback of MIDI files on the Digital Piano.
Playing Back a MIDI File You can use the Digital Piano to directly playback a MIDI file stored on an SD card. You also can copy MIDI files to the Digital Piano’s built-in memory (internal memory area) and play it back from there. IMPORTANT! • Your Digital Piano supports playback of Format0 and Format1 SMF files and CM2 (CASIO proprietary) format file. Playback of up to 17 tracks of a Format1 SMF file is supported. • Playback of audio files (WAV, MP3, etc.) is not supported. 5.
Playing Back a MIDI File 3. Press the (CARD PLAYER) button so the lamp below it is lit. This is the CARD PLAYER mode. • This displays the name of the first MIDI file in the internal memory area. • The remaining steps of this procedure are the same as those starting with step 6 under “To play back a MIDI file from an SD card” (page E-41). ■ To adjust the tempo by tapping a beat 1.
Playing Back a MIDI File NOTE • To perform the procedure below, use a MIDI file that has the left-hand part recorded in Channel 3 and the right-hand part recorded in Channel 4. 1. Enter the CARD PLAYER mode and select the MIDI file you want to play. 2. Press the (PART) button. To play on the keyboard along with playback 1. • See “Selecting a Tone” (page E-11) and “Layering and Splitting Tones” (page E-12). 2. • This will display the part on/off screen (L-[ON] R-[ON]) to appear on the display.
Playing Back a MIDI File To select a tone for each zone in the CARD PLAYER mode 1. Press the (LAYER) and (SPLIT) buttons so their lamps are lit in the combinations shown below and select the tones you want. To change this zone’s tone: Configure the (LAYER) and (SPLIT) button lamps like this: UPPER 1 zone (LAYER): unlit, (SPLIT): unlit (LAYER): lit, (SPLIT): unlit (LAYER): unlit, (SPLIT): lit (LAYER): lit, (SPLIT): lit UPPER 2 zone LOWER 1 zone LOWER 2 zone 2.
Playing Back a MIDI File Enter a name for the folder you want to create. • Use the (u) and (i) buttons to move the cursor left and right, and the (w, q) buttons to English 6. scroll through characters at the current cursor position. The following shows the characters that can be used in a name.
Using a Memory Card MASTER CONTROL You can save Digital Piano registration data to a commercially available SD memory card, if you want. Use a memory card with a capacity of 2GB or less. Use of a card with a capacity that is greater than 2GB or other types of memory cards is not supported. In this manual, mentions of a “memory card” refer to an SD memory card.
Using a Memory Card Use the (u) and (i) buttons to display “CardFORMAT” and then press the (ENTER) button. To rename a file on a memory card 1. This will display a confirmation message (SURE?). • If you want to cancel the format operation, press the (NO) or (EXIT) button. 5. Press the (YES) button. • The message “Please Wait” will remain on the display while the format operation is being performed. Do not perform any Digital Piano operation while this message is on the display.
Using a Memory Card Error Messages One of the error messages below appears on the display when a problem occurs. • All mentions of “memory card” in the following table refer to an SD memory card. Display Message Format MediaFull Media R/W No Card Cause Required Action 1. The current memory card format is not compatible with this Digital Piano. 1. Format the memory card on the Digital Piano (page E-46). 2. The memory card capacity is greater than 2GB. 2.
Connecting to a Computer You can connect the Digital Piano to a computer and exchange MIDI data between them. You can send play data from the Digital Piano to music software running on your computer, or you can send MIDI data from your computer to the Digital Piano for playback. 2. CARD PLAYER After starting up your computer, use a commercially available USB cable to connect it to the Digital Piano.
Connecting to a Computer Transferring Data between the Digital Piano and a Computer 3. While holding down the (FUNCTION) button, press the (USB DEVICE MODE) button. This will enter the storage mode, which enables data transfer with the connected computer. The (FUNCTION) button lamp will flash and the display will appear as shown below. You can use the procedure below to transfer registration data from the Digital Piano to a computer for storage.
Connecting to a Computer File name extensions (.MID, .CM2, etc.) are not displayed under initial default Windows settings. Perform the procedure below to turn on display of file name extensions. (1) Perform one of the following operations to display folder information. • Windows XP: On the [Tools] menu at the top of the folder window, select [Folder Options]. • Windows Vista, Windows 7: On the left side of the folder window, click [Organize] and then select [Folder and Search Options].
Reference Troubleshooting Problem Nothing comes out of the connected headphones or amplifier speakers when I play something. Cause The (VOLUME) knob is set to “MIN”. The UPPER 1 zone setting is INT OFF. The pitch of the Digital Piano is off. The Digital Piano’s key setting is something other than 0. Digital Piano tuning is incorrect. Tones and/or effects sound strange. Turning power off and then back on again does not eliminate the problem.
Problem A tone’s quality and volume sounds slightly different depending where it is played on the keyboard. Cause Action See Page This is an unavoidable result of the digital sampling process,* and does not indicate malfunction. * Multiple digital samples are taken for the low range, middle range, and high range of the original musical instrument. Because of this, there may be a very slight difference in tonal quality and volume between sample ranges.
Reference Product Specifications Model PX-3 Keyboard 88-key piano keyboard, with Touch Response (3 types) Maximum Polyphony 128 notes Tones 250 (with Layer and Split) Effects DSP, Reverb (4 types), Chorus (4 types), Brilliance (–3 to 0 to 3), Acoustic Resonance Mixer UPPER 1, UPPER 2, LOWER 1, LOWER 2; the volume level of each zone can be adjusted independently.
Operating Precautions Be sure to read and observe the following operating precautions. ■ Location Avoid the following locations for this product. • Areas exposed to direct sunlight and high humidity • Areas subjected to temperature extremes • Near a radio, TV, video deck, or tuner • The above devices will not cause malfunction of the product, but the product can cause interference in the audio or video of a nearby device.
Reference AC Adaptor Handling Precautions Model: AD-A12150LW 1. Read these instructions. 2. Keep these instructions on hand. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this product near water. 6. Clean only with a dry cloth. 7. Do not install near radiators, heat registers, stoves, or any other source of heat (including amplifiers). 8. Use only attachments and accessories specified by the manufacturer. 9. Refer all servicing to qualified service personnel.
Tone List Sequential Number Group Name Group Number Tone Name Program Change Bank Select MSB 0 0 1 0 1 0 0 1 0 1 0 0 3 3 6 48 49 48 50 49 51 52 50 53 51 54 55 48 49 48 Equalizer – – Equalizer Equalizer – – Equalizer Compressor Equalizer Enhancer Enhancer – – – 6 49 – 4 4 4 4 4 4 48 49 50 51 52 53 DSP Algorithm 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 PIANO PIANO PIANO PIANO PIANO PIANO PIANO PIANO PIANO PIANO PIANO PIANO PIANO PIANO PIANO 001 002 003 004 005 006 007 008 009 010 011 012
Appendix Sequential Number Group Name Group Number 129 130 131 132 133 134 135 136 OTHERS/GM OTHERS/GM OTHERS/GM OTHERS/GM OTHERS/GM OTHERS/GM OTHERS/GM OTHERS/GM 037 038 039 040 041 042 043 044 137 OTHERS/GM 045 138 OTHERS/GM 046 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 OTHERS/GM OTHERS/GM OTHERS/GM OTHERS/GM OTHERS/GM OTHERS/GM OTHERS/GM OTHERS/GM OTHERS/GM OTHERS/GM OTHERS/GM OTHERS/GM OTHERS/GM OTHERS/GM OTHERS/GM OTHERS/GM OTHERS/GM OTHERS/GM 047 048 049 05
29 F1 41 F2 53 F3 65 F4 77 F5 89 F6 30 42 39 54 51 66 63 78 75 Eb6 87 C # 6 85 B b 5 82 A b 5 80 F#5 Eb5 C # 5 73 B b 4 70 A b 4 68 F#4 Eb4 C # 4 61 B b 3 58 A b 3 56 F#3 Eb3 C # 3 49 B b 2 46 A b 2 44 F#2 Eb2 C # 2 37 B b 1 34 A b 1 32 F#1 27 High Q Slap Scratch Push Scratch Pull Sticks Square Click Metronome Click Metronome Bell Standard1 Kick 2 Standard1 Kick 1 Side Stick Standard1 Snare 1 Hand Clap Standard1 Snare 2 Low Tom 2 Closed Hi-Hat Low Tom 1 Pedal
Appendix DSP Effect List The table below shows the DSP types that can be configured for each zone using zone parameters (page E-28). • The “DSP No.” column shows the DSP type numbers that appear on page 3 of the zone menu, and “Screen Name” shows the name (abbreviated) that appears on the screen. “DSP Name” shows the full version of the screen name. • For information about the parameters of a DSP type, note the value for it shown in the “Algorithm No.
Appendix Single-effect Algorithms 01: Equalizer This is a three-band equalizer. Parameter Value Ranges: 0 : Equalizer 1 Frequency (1.0, 1.3, 1.6, 2.0, 2.5, 3.2, 4.0, 5.0 [KHz]) Adjusts the center frequency of Equalizer 1. 1 : Equalizer 1 Gain (–12 to 0 to +12) Adjusts the gain of Equalizer 1. 2 : Equalizer 2 Frequency (1.0, 1.3, 1.6, 2.0, 2.5, 3.2, 4.0, 5.0 [KHz]) Adjusts the center frequency of Equalizer 2. 3 : Equalizer 2 Gain (–12 to 0 to +12) Adjusts the gain of Equalizer 2.
Appendix 08: Rotary This is a rotary speaker simulator. Parameter Value Ranges: 0 : Speed (Slow, Fast) Switches the speed mode between fast and slow. 1 : Brake (Rotate, Stop) Stops speaker rotation. 2 : Fall Acceleration (0 to 127) Adjusts acceleration when the speed mode is switched from fast to slow. 3 : Rise Acceleration (0 to 127) Adjusts acceleration when the speed mode is switched from slow to fast. 4 : Slow Rate (0 to 127) Adjusts the speaker rotation speed in the slow speed mode.
Appendix This is a “wah” effect that can automatically shift the frequency in accordance with the level of the input signal. Parameter Value Ranges: 0 : Input Level (0 to 127) Adjusts the input level. The input signal can become distorted when the level of the sound being input, the number of chords, or the Resonance value is large. Adjust this parameter to eliminate such distortion. 1 : Resonance (0 to 127) Adjusts the strength of resonance.
Appendix M03: Multi03 (Compressor - Enhancer) M08: Multi08 (Auto Wah - Phaser) 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 8 9 : Compressor Depth : Compressor Attack : Compressor Release : Compressor Level : Enhancer Low Frequency : Enhancer Low Gain : Enhancer High Frequency : Enhancer High Gain M04: Multi04 (Compressor - Chorus) 0 1 2 3 4 5 6 7 8 : Compressor Depth : Compressor Attack : Compressor Release : Compressor Level : Chorus Rate : Chorus Depth : Chorus Feedback : Chorus Wet Level : Chorus Polarity M0
M13: Multi13 (Distortion - Auto Pan) M19: Multi19 (Phaser - Chorus - Auto Pan) 0 1 2 3 4 5 6 7 0 : Phaser Resonance 1 : Phaser Manual 2 : Phaser Rate 3 : Phaser Depth 4 : Phaser Wet Level 5 : Chorus Rate 6 : Chorus Depth 7 : Chorus Feedback 8 : Chorus Wet Level 9 : Auto Pan Rate 10 : Auto Pan Depth : Distortion Gain : Distortion Low : Distortion High : Distortion Level : Auto Pan Rate : Auto Pan Depth : Distortion Skip : Auto Pan Skip M14: Multi14 (Distortion - Tremolo) 0 1 2 3 4 5 6 7 : Distortion Ga
Appendix M23: Multi23 (LFO Wah - Distortion - Chorus) 0 : Wah Input Level 1 : Wah Resonance 2 : Wah Manual 3 : Wah LFO Rate 4 : Wah LFO Depth 5 : Distortion Gain 6 : Distortion Low 7 : Distortion High 8 : Distortion Level 9 : Chorus Rate 10 : Chorus Depth 11 : Chorus Feedback 12 : Chorus Wet Level 13 : Chorus Polarity 14 : Distortion Skip M24: Multi24 (Auto Wah - Distortion - Chorus) 0 : Wah Input Level 1 : Wah Resonance 2 : Wah Manual 3 : Wah Depth 4 : Distortion Gain 5 : Distortion Low 6 : Distortion Hi
MIDI Implementation Chart Model PX-3 Function Transmitted Recognized Basic Channel Default Changed 1 - 16 1 - 16 1 - 16 1 - 16 Mode Default Messages Altered Mode 3 X Mode 3 X 0 - 127 0 - 127 0 - 127*1 O 9nH v = 1 - 127 X 8nH v = 64 O 9nH v = 1 - 127 X 9nH v = 0, 8nH v =** X X X O O O Note Number True voice Velocity Note ON Note OFF After Touch Key’s Ch’s Pitch Bender ° ± µ ¶¬ ³¸ · ±° ±± ±¶ ±· ±¸ ±¹ ¶´ ¶µ ¶¶ ¶· ·± ·² ·³ ·´ ·¶ ·· ·¸ ¸° ¸± ¸² ¸³ ¸´ ¹± ¹³ ±°°¬ ±°± ±²° ±²± °±²· Contr
This recycle mark indicates that the packaging conforms to the environmental protection legislation in Germany. Esta marca de reciclaje indica que el empaquetado se ajusta a la legislación de protección ambiental en Alemania.
