User manual

Copyrights and Registered
Copyrights
●
Bluetooth
®
is a registered trademark of
Bluetooth SIG, Inc.
●
iPhone and App Store are registered
trademarks of Apple Inc. in the United
States and other countries.
●
iOS is a trademark or registered trademark
of Cisco Systems, Inc.
●
GALAXY, GALAXY Note, and GALAXY S
are registered trademarks of Samsung
Electronics Co., Ltd.
●
Android and Google Play
TM
are registered
trademarks of Google Inc.
●
Other company names and product names
used herein are trademarks or registered
trademarks of their respective companies.
Troubleshooting
Signal Reception (GPS)
Q1
The watch cannot perform a receive
operation.
Is the watch’s battery charged?
Signal reception is not possible while
battery power is low. Keep the watch
exposed to light until it recharges
sufficiently.
l
Solar Charging
Is the watch in the Timekeeping Mode?
Signal reception is not possible unless the
watch
is in the Stopwatch Mode. Note that
signal reception is also disabled in the
Airplane Mode. Return to the
Timekeeping Mode and/or exit the
Airplane Mode.
l
Navigating Between Modes
After checking the above, the watch still
cannot perform a receive operation.
GPS signal reception is not possible
under the conditions described below.
●
During power saving
●
While the crown is pulled out
●
Timer
countdown operation in progress
Q2
The
second hand remains at “T+P” or
“T(TIME)” during the signal receive
operation.
The watch may be receiving leap second
information.
l
Leap Second Reception
Q3
The signal receive operation always
fails.
Is the watch in a location that is appropriate
for signal reception?
Check your surroundings and move the
watch
to a location where signal reception
is better.
l
Appropriate
Signal Reception Location
Is the face of the watch pointed straight
upwards at the sky?
Minimize movement of the watch while the
receive operation is in progress.
When
the watch is set up for auto receive,
take care to avoid covering the watch face
with the sleeve of your clothing.
An alarm started sounding while the
receive operation was in progress.
Receive stops if an alarm operation starts
while it is being performed. Disable the
alarm.
l
Enabling/Disabling the Alarm
Q4
Signal reception should have been
successful,
but the watch’s time and/
or day is wrong.
Is your Home City setting correct for your
location?
Change your Home City setting so it
correctly reflects your location.
l
Acquiring GPS Location Information
Manually
l
Setting a Home Time City
Is the hand and/or day indicator alignment
correct?
Adjust hand and/or day indicator
alignment.
l
Adjusting Hand and Day Indicator
Alignment
After checking the above, the time and/or
day settings is still wrong.
Adjust time and day settings manually.
Signal Reception (Time
Calibration Signal)
Q1
The watch cannot perform a receive
operation.
Is the watch’s battery charged?
Signal reception is not possible while
battery power is low. Keep the watch
exposed to light until it recharges
sufficiently.
l
Solar Charging
Is the watch in the Timekeeping Mode?
Signal reception is not possible unless the
watch
is in the Stopwatch Mode. Note that
signal reception is also disabled in the
Airplane Mode. Return to the
Timekeeping Mode and/or exit the
Airplane Mode.
l
Navigating Between Modes
Is your Home City setting correct for your
location?
The watch will not indicate the correct time
if
the Home City setting is wrong. Change
your Home City setting so it correctly
reflects your location.
l
Acquiring GPS Location Information
Manually
l
Setting a Home Time City
After checking the above, the watch still
cannot perform a receive operation.
Time calibration signal reception is not
possible under the conditions described
below.
●
When watch is at Level 2 power saving
●
When the crown is pulled out
●
Timer
countdown operation in progress
If successful reception is not possible for
some
reason, you can adjust the time and
day settings manually.
Operation Guide 5502
22