E Digital Camera EX-Z4 User’s Guide Thank you for purchasing this CASIO Product. • Before using it, be sure to read the precautions contained in this User’s Guide. • Keep the User’s Guide in a safe place for future reference. • For the most up-to-date information about this product, visit the official Exilim Website at http://www.exilim.com/.
INTRODUCTION INTRODUCTION Unpacking Check to make sure that all of the items shown below are included with your camera. If something is missing, contact your dealer as soon as possible. PHOTO CHARGE USB Camera Rechargeable lithium ion battery (NP-20) USB Cradle (CA-21A) Strap CD-ROM USB Cable * The shape of the AC power cord plug varies according to country or geographic area.
INTRODUCTION 19 Contents GETTING READY About This Manual ..................................................... 19 2 General Guide ............................................................ 20 INTRODUCTION Camera USB Cradle Unpacking .................................................................... 2 Monitor Screen Contents ........................................... 22 Features .......................................................................
INTRODUCTION 44 Exposure Compensation (EV Shift) ........................... 65 BASIC IMAGE RECORDING Adjusting White Balance ............................................ 66 Recording an Image ................................................... 44 Aiming the Camera Recording an Image Recording Precautions About Auto Focus About the REC Mode Monitor Screen Adjusting White Balance Manually 67 44 45 47 48 48 Using the BESTSHOT Mode .....................................
INTRODUCTION 88 PLAYBACK 107 Basic Playback Operation .......................................... 88 Playing an Audio Snapshot DELETING FILES Deleting a Single File ............................................... 107 89 Deleting All Files ...................................................... 108 Flipping the Display .................................................... 90 Zooming the Display Image ....................................... 91 109 FILE MANAGEMENT Resizing an Image ...................
INTRODUCTION 121 OTHER SETTINGS 134 Configuring Sound Settings ..................................... 121 To configure sound settings To set the volume level Using a Memory Card .............................................. 135 121 122 To insert a memory card into the camera To remove a memory card from the camera Formatting a Memory Card Memory Card Precautions Specifying an Image for the Startup Screen ........... 122 Configuring Power Down Image Settings ................
INTRODUCTION 154 USING THE CAMERA WITH A COMPUTER 168 Using the Album Feature ......................................... 154 Creating an album Selecting an Album Layout Configuring Detailed Album Settings Viewing Album Files Saving an Album Menu Reference ....................................................... 168 154 155 156 158 161 Indicator Lamp Reference .......................................
INTRODUCTION • The USB driver (mass storage) uses Phoenix Technologies Ltd. software. Compatibility Software Copyright C 1997 Phoenix Technologies Ltd., All Rights Reserved. • Other company, product and service names used herein may also be trademarks or service marks of others. • Photo Loader and Photohands are the property of CASIO COMPUTER CO., LTD. Except as stipulated above, all copyrights and other related rights to these applications revert to CASIO COMPUTER CO., LTD.
INTRODUCTION • Easy Image Transfer Transfer images to a computer simply by placing the camera onto the USB cradle. Features • 4.0 million Effective Pixels A high-resolution megapixel CCD provides 4.0 million effective pixels (4.23 million total pixels) for images that print beautifully. • Photo Stand feature A slideshow of images in file memory can be played while the camera is on its USB cradle. • 2.
INTRODUCTION • Movie + Audio Mode • Real-time histogram An on-screen histogram lets you adjust exposure as you view the effect on overall image brightness, which makes shooting under difficult lighting conditions easier than ever before. • Voice Recording Quick and easy recording of voice input. • After Recording Adds audio to images after they are recorded. • World Time A simple operation sets the current time for your current location. You can select from among 162 cities in 32 time zones.
INTRODUCTION • USB DIRECT-PRINT support Your camera supports USB DIRECT-PRINT, which was developed by Seiko Epson Corporation. When connected directly to a printer that supports USB DIRECT-PRINT, you can select images to print and start the print operation directly from the camera. Precautions General Precautions Be sure to observe the following important precautions whenever using the EX-Z4.
INTRODUCTION • Never fire the flash while it is too close to the subject’s eyes. Intense light from the flash can cause eye damage if it is fired too close to the eyes. This is especially true with young children. When using the flash, the camera should be at least one meter (3.3´) from the eyes of the subject. • Keep the camera away from water and other liquids, and never let it get wet. Moisture creates the danger of fire and electric shock.
INTRODUCTION Data Error Precautions Operating conditions • Your digital camera is manufactured using precision digital components. Any of the following creates the risk of corruption of data in file memory. • This camera is designed for use in temperatures ranging from 0°C to 40°C (32°F to 104°F). • Do not use or keep the camera in the following areas.
INTRODUCTION Condensation Lens • When you bring the camera indoors on a cold day or otherwise expose it to a sudden change of temperature, there is the possibility that condensation can form on the exterior or on interior components. Condensation can cause malfunction of the camera, so you should avoid exposing it to conditions that might cause condensation.
QUICK START GUIDE QUICK START GUIDE First, charge the battery! 1. Load the battery (page 26). 2. Place the camera onto the USB cradle to charge the battery (page 28). 1 • It takes about two hours to achieve a full charge.
QUICK START GUIDE To configure display language and clock settings • Be sure to configure the following settings before using the camera to record images. (See page 40 for details.) 1. Press the power button to turn on the camera. 2. Press [ ] to select the language you want. 1 3. Press [SET] to register the language setting. 4. Use [ ], [ ], [ ], and [ ] to select the geographical PLAY REC MENU SET DISP 2, 3, 4, 5, 6, 7, 8, 9 area you want, and then press [SET]. 5.
QUICK START GUIDE To record an image To view a recorded image (See page 44 for details.) Green operation lamp 2 1 4 (See page 88 for details.) 2 1 99 1600 1200 NORMAL IN 1 / 1000 F2.6 PLAY 03/12 03 12/24 24 12:58 12 58 PLAY REC REC MENU MENU SET 3 SET Focus frame DISP DISP 3 1. Press the power button to turn on the camera. 1. Press the power button to turn on the camera. 2. Align the mode selector with “REC”. 3.
QUICK START GUIDE To delete an image (See page 107 for details.) 2 1 PLAY REC MENU SET DISP 3, 4, 5, 6 1. Press the power button to turn on the camera. 2. Align the mode selector with “PLAY”. 3. Press [ ] ( ). 4. Use [ ] and [ ] to display the image you want to delete. 5. Use [ ] and [ ] to select “Delete”. • To exit the image delete operation without deleting anything, select “Cancel”. 6. Press [SET] to delete the image.
GETTING READY GETTING READY ■ Button Operations This section contains information about things you need to know about and do before trying to use the camera. Button operations are indicated by the button name inside of brackets ([ ]). About This Manual ■ On-screen Text This section contains information about the conventions used in this manual. On-screen text is always enclosed by double quotation marks (“ ”).
GETTING READY General Guide The following illustrations show the names of each component, button, and switch on the camera.
GETTING READY ■ Bottom USB Cradle Simply placing your CASIO digital camera onto the USB cradle lets you perform the following tasks. • Battery charging (page 28) • Automatic transfer of images to a computer (page 140) • Viewing of images using the Photo Stand slideshow feature (page 101). H I J ■ Front H Battery compartment cover I Connector J Tripod screw hole 12 3 * Use this hole when attaching to a tripod.
GETTING READY Monitor Screen Contents The monitor screen uses various indicators and icons to keep you informed of the camera’s status. REC mode 1 2 34 5 1 Flash Mode indicator 6 None Auto 4 Self-timer None Flash Off C 10s 7 Flash On 8 Red-eye reduction 9 0 • If the camera detects that flash is required while auto flash is selected, the flash on indicator will appear when the shutter release button is pressed half way.
GETTING READY D D Digital zoom indicator E Shutter speed value E F G • An out of range aperture or shutter speed causes the corresponding monitor screen value to turn amber. F Aperture value G ISO sensitivity H H Zoom indicator • Left side indicates optical zoom. • Right side indicates digital zoom.
GETTING READY PLAY mode 12 3 4 1 PLAY mode file type 5 Snapshot Audio Voice Recording 2 Image protection indicator 3 Folder number/File number 8 FINE NORMAL ECONOMY Movie 6 7 5 Quality Snapshot 4 Image size 2304 2304 1600 1280 640 ҂ 1728 ҂ 1536 ҂ 1200 ҂ 960 ҂ 480 pixels (3:2) pixels pixels pixels pixels 24 6 Built-in memory selected for data storage. Memory card selected for data storage.
GETTING READY Changing the Contents of the Monitor Screen Indicator Lamps You can find out the operational status of the camera and the USB cradle at a glance by checking the color of the indicator lamps, and whether a lamp is lit or flashing. For details, see “Indicator Lamp Reference” on page 170. Each press of the [DISP] button changes the contents of the monitor screen as shown below.
GETTING READY Attaching the Strap Power Requirements Attach the strap to the strap ring as shown in the illustration. Your camera is powered by a rechargeable lithium ion battery (NP-20). To load the battery PLAY REC 1. While pressing the battery compartment MENU cover on the bottom of the camera, slide the cover in the direction indicated by the arrow, and then swing it open.
GETTING READY 2. While pulling the stopper in the direction 3. Swing the battery compartment cover closed, indicated by the arrow in the illustration, align the arrow mark on the battery with the arrow mark on the camera and slide the battery into the camera. and then slide it in the direction indicated by the arrow. Stopper IMPORTANT! • Use only the special NP-20 rechargeable lithium ion battery to power this camera. Use of any other type of battery is not supported.
GETTING READY To remove the battery To charge the battery 1. Open the battery compartment cover. 1. Connect the bundled AC adaptor to the [DC IN 5.3V] connector of the USB cradle, and then plug it in to a household power outlet. 2. Pull the stopper in the direction indicated by the arrow. USB Cradle • This will cause the battery to come part way out of the slot. [DC IN 5.3V] AC Adaptor Stopper AC power cord 3. Release the stopper and pull the battery from the camera.
GETTING READY 2. Turn off the camera. NOTE • The bundled AC adaptor is designed for operation with any power supply in the range of 100V to 240V AC. Note, however, that the shape of the AC power cord plug varies according to country or geographic area.
GETTING READY IMPORTANT! • If the [CHARGE] lamp starts flashing red, it means that an error occurs while charging. An error can be caused by any of the following: a problem with the USB cradle, a problem with the camera, or a problem with the battery or how it is loaded. Remove the camera from the USB cradle and see if it works normally. • You can use the USB cradle to charge the camera’s battery, to exchange data with a computer over a USB connection, or when using the Photo Stand feature only.
GETTING READY ■ If the camera works normally ■ Battery Life Guidelines The battery life guideline values given below indicate the amount of time under the conditions defined below the table, until power automatically turns off due to battery failure. They do not guarantee that the battery will provide the amount of service indicated. Low temperatures and continued use reduce battery life. 1. Continue using the camera until the current charge is used up, and then charge the battery.
GETTING READY *2 Normal Recording Conditions • Temperature: 23°C (73°F) • Monitor Screen: On • Zoom operation between full wide to full telephoto every 30 seconds, during which two images are recorded, one image with flash; power turned off and back on every time 10 images are recorded.
GETTING READY • Failure to observe any of the following precautions while using the battery creates the risk of overheating, fire, and explosion. — Never use any other type of charger except the optional charger unit specified for the battery. — Never try to use the battery to power any other device other than this camera. — Never use or leave the battery near open flame. — Never place the battery in a microwave oven, throw it into fire, or otherwise expose it to intense heat.
GETTING READY ● PRECAUTIONS DURING USE • Should you ever notice leakage, strange odor, heat generation, discoloration, deformation, or any other abnormal condition while using, charging, or storing a battery, immediately remove it from the camera or optional charger unit and keep it away from open flame. • If the battery does not achieve full charge after the normal charging time has passed, stop charging. Continued charging creates the risk of overheating, fire, and explosion.
GETTING READY ■ USB Cradle and AC Adaptor Precautions ● BATTERY STORAGE PRECAUTIONS • Make sure you remove the battery when you do not plan to use the camera for a long time. A battery left in the camera discharges very small amounts of power even when power is turned off, which can lead to a dead battery or the need for longer charging before the next use. • Store the battery in a cool, dry place (20°C (68 °F) or lower).
GETTING READY Caution! • Use the AC adaptor where it will not be splashed with water. Water creates the risk of fire and electric shock. • Do not place a vase or any other container filled with liquid on top of the AC adaptor. Water creates the risk of fire and electric shock. Turning the Camera On and Off Press the power button to turn the camera on and off. Pressing the power button to turn on the camera causes the green operation lamp to light temporarily.
GETTING READY ● See page 38 for information about how to use menus. Configuring Power Saving Settings You can configure the settings described below to conserve battery power. Sleep : Automatically turns off the monitor screen if no operation is performed for a specified amount of time in the REC mode. Performing any button operation causes the monitor screen to turn back on. Auto Power Off : Turns off power if you do not perform any operation for a specified amount of time.
GETTING READY 2. Press [MENU]. Using the On-screen Menus Pressing [MENU] displays menus on the monitor screen that you can use to perform various operations. The menu that appears depends on whether you are in the REC mode or the PLAY mode. The following shows an example menu procedure in the REC mode. 1. Turn on the camera, and then align the mode selector with “REC” to enter the REC mode.
GETTING READY ● Menu Screen Operations 3. Press [ ] or [ ] to select the tab you want, When you want to do this: Do this: Move between tabs Press [ ] and [ ]. Move from the tab to the settings Press [ ]. Move from the settings to the tab Press [ ]. Move between the settings Press [ ] and [ ]. Display the options available for a setting Press [ ] or press [SET]. Select an option Press [ ] and [ ]. Register an option selection and exit the menu screen Press [SET].
GETTING READY 6. Perform one of the following operations to Configuring Display Language and Clock Settings apply the setting you configured. To do this: Perform this key operation: Apply the setting and exit the menu screen. Press [SET]. Apply the setting and return to feature selection in step 4. Press [ ]. Apply the setting and return to tab selection in step 3. 1. Press [ ]. 2. Use [ ] to move back up to tab selection.
GETTING READY IMPORTANT! To configure display language and clock settings • The camera’s clock settings are cleared whenever power is totally cut off. This can happen if the battery goes dead while the camera is not being supplied power by the USB cradle. The clock setting screen will appear automatically the next time you turn on power after the settings are cleared. Set the date and time before using the camera.
GETTING READY 3. Use [ ], [ ], [ ], and 6. Use [ ] and [ ] to [ ] to select the geographical area where you live, and then press [SET]. change the date format setting, and then press [SET]. Example: December 24, 2003 4. Use [ ] and [ ] to select the name of the city where you live, and then press [SET]. 5. Use [ ] and [ ] to select the summer time (DST) setting you want, and then press [SET].
GETTING READY 7. Set the current date and the time. To do this: Do this: Change the setting at the current cursor location Press [ ] and [ ]. Move the cursor between settings Press [ ] and [ ]. Toggle between 12-hour and 24hour timekeeping Press [DISP]. 8. Press [SET] to register the settings and exit the setting screen.
BASIC IMAGE RECORDING BASIC IMAGE RECORDING This section describes the basic procedure for recording an image. IMPORTANT! • Make sure your fingers or the strap does not block the flash, microphone or lens. Recording an Image Flash Microphone Aiming the Camera Lens Use both hands to hold the camera still when shooting an image. Holding the camera with one hand increases the chance of movement, which can blur your images.
BASIC IMAGE RECORDING 3. Compose the image Recording an Image on the monitor screen so the main subject is within the focus frame. Your camera automatically adjusts shutter speed in accordance with the brightness of the subject. Images you record are stored in the camera’s built-in memory, or to a memory card if you have one loaded in the camera. • When an optionally available SD memory card or MultiMediaCard (MMC) is loaded in the camera, images are stored on the card (page 134). 1.
BASIC IMAGE RECORDING ● Operation Lamp and Focus Frame Operation 4. Press the shutter release button half way to focus the image. • When you press the shutter release button half way, the camera’s Auto Focus feature automatically focuses the image, and displays the shutter speed and aperture values. • You can tell whether the image is focused by observing the focus frame and the green operation lamp.
BASIC IMAGE RECORDING 5. After making sure that the Recording Precautions image is focused properly, press the shutter release button the rest of the way down to record. • The number of images that can be stored in memory depends on the resolution setting you are using (pages 57,178). • Never open the battery compartment cover or place the camera onto the USB cradle while the green operation lamp is flashing.
BASIC IMAGE RECORDING About Auto Focus About the REC Mode Monitor Screen • Auto Focus tends not to work well if the camera is moved during recording, or when recording the types of subjects listed below.
BASIC IMAGE RECORDING IMPORTANT! Using the Optical Viewfinder • The frame that is visible inside of the viewfinder indicates the image recorded at a distance of about one meter (3.3´). When the subject is closer than one meter, the recorded image will be different from what you see inside the viewfinder frame. • Since the monitor screen shows exactly what will be recorded, always use it for composing your images in the Macro and Manual Focus modes.
BASIC IMAGE RECORDING Using Zoom Your camera is equipped with two types of zoom: optical zoom and digital zoom. Optical Zoom Zoom out Zoom in The range of the optical zoom factor is shown below. Optical Zoom Factor Range: 1X to 3X 2. Compose the image and then press the shutter release button. 1. In the REC mode, press the zoom button to change the zoom factor. NOTES REC • The optical zoom factor also affects the lens aperture.
BASIC IMAGE RECORDING 5. Hold down the Digital Zoom Digital zoom indicator (Telephoto) zoom button to increase the optical zoom factor. Digital zoom is activated after you reach the maximum optical zoom factor (3X). It enlarges the part of the image at the center of the image screen. The range of the digital zoom factor is shown below. • When the digital zoom factor reaches its maximum value (3X), it stops momentarily.
BASIC IMAGE RECORDING IMPORTANT! Using the Flash • Digital zoom is disabled whenever the monitor screen is turned off (page 25). • Using digital zoom can cause degradation of the recorded image. Perform the following steps to select the flash mode you want to use. 1. In the REC mode, press [MENU]. 2. Press [왔] ( ) to select the flash mode. MENU • Each press of [왔] ( ) cycles through the flash mode settings shown below on the monitor screen.
BASIC IMAGE RECORDING To do this: Have the flash fire automatically when required (Auto Flash) ■ About Red-eye Reduction Select this setting: Using the flash to record at night or in a dimly lit room can cause red spots inside the eyes of people who are in the image. This is caused when the light from the flash reflects off of the retina of the eye.
BASIC IMAGE RECORDING Flash Unit Status Flash Precautions You can find out the current flash unit status by pressing the shutter release button half way and checking the monitor screen and red operation lamp. Take care that your fingers do not block the flash when you hold the camera. Covering the flash with your finger can greatly reduce its effectiveness. The indicator is also shown on the monitor screen when the flash unit is ready to fire.
BASIC IMAGE RECORDING • Using flash in combination with another light source (daylight, fluorescent light, etc.) can result in abnormal image colors. Using the Self-timer The self-timer lets you select either a 2-second or 10second delay of the shutter release after you press the shutter release button. A Triple Self-timer feature lets you perform three consecutive self-timer operations to record three images. 1. In the REC mode, press [MENU]. 2. Use [왗] and [왘] to select the “REC” tab. 3.
BASIC IMAGE RECORDING To do this: 5. Record the image. Select this setting: Specify a 10-second self-timer 10 sec Specify a 2-second self-timer 2 sec Specify Triple Self-timer X3 Disable the self-timer Off Self-timer lamp • When you press the shutter release button, the self-timer lamp flashes and the shutter releases after the selftimer reaches the end of its countdown. • With the Triple Self-timer, the camera records a series of three images in the sequence described below.
BASIC IMAGE RECORDING NOTES Specifying Image Size and Quality • If you plan to make large prints of your images or otherwise use them in applications where highresolution is your top priority, select the “2304 x 1728” image size. • If you plan to send images as e-mail attachments or otherwise use them in applications where data economy is your top priority, select the “640 x 480” image size.
BASIC IMAGE RECORDING NOTE To specify image quality • Use the “Fine” setting when image quality is your top priority and file size is secondary. Conversely, use the “Economy” setting when file size is your top priority and image quality is secondary. 1. In the REC mode, press [MENU]. 2. Use [왗] and [왘] to select the “REC” tab. 3. Use [왖] and [왔] to select “Quality”, and then IMPORTANT! press [왘]. • Actual file size depends on the type of image you record.
OTHER RECORDING FUNCTIONS OTHER RECORDING FUNCTIONS This section describes other powerful features and functions that are available for recording. Using Auto Focus As its name suggests, Auto Focus focuses the image automatically. The automatic focus operation starts when you press the shutter release button down half way. The following is the Auto Focus range. Selecting the Focus Mode You can select one of five different focus modes: Auto Focus, Macro, Pan Focus, Infinity, and Manual. 1.
OTHER RECORDING FUNCTIONS When you see this: It means this: Green focus frame Green operation lamp The image is focused. Red focus frame Flashing green operation lamp The image is not in focus. 3. Select the Auto Focus area you want, and then press [SET]. 3. Press the shutter release button the rest of the way to record the image. ■ Specifying the Auto Focus Area You can use the following procedure to change the Auto Focus area used in the Auto Focus Mode and the Macro Mode.
OTHER RECORDING FUNCTIONS Using the Macro Mode Using the Pan Focus Mode The Macro mode lets you focus automatically on close up subjects. The automatic focus operation starts when you press the shutter release button down half way. The following is the focus range in the Macro mode. Normally, your camera performs Auto Focus to ensure that your images are always in focus. With Pan Focus, focus is fixed for a specific focal distance, and images are recorded without Auto Focus.
OTHER RECORDING FUNCTIONS 1. Keep pressing [왖] ( ) until the focus mode Using the Infinity Mode indicator shows “PF”. The Infinity mode fixes focus at infinity (∞). Use this mode when recording scenery and other faraway images. 2. Press the shutter release button all the way down. 1. Keep pressing [왖] ( indicator shows “ NOTE • If you press the shutter release button half way, the focus distance will appear on the monitor screen. 2. Record the image.
OTHER RECORDING FUNCTIONS 2. While watching the Using Manual Focus image on the monitor screen, use [왗] and [왘] to focus. With the Manual Focus mode, you can adjust the focus of an image manually. The following shows focus ranges in the Macro mode for two optical zoom factors. Optical Zoom Factor Approximate Focus Range 1X 6cm (2.4˝) to infinity (∞) 3X 18cm (7.1˝) to infinity (∞) Manual focus position To do this: 1. Keep pressing [왖] ( ) until the focus mode indicator shows “MF”.
OTHER RECORDING FUNCTIONS 2. Keeping the shutter Using Focus Lock Focus lock is a technique you can use to focus on a subject that is not located within the focus frame when you record an image. You can use focus lock in the Auto Focus mode and the Macro mode ( ). release button half way down, recompose the image as you like. 1. Using the monitor • This locks the focus on the subject that is currently within the focus frame.
OTHER RECORDING FUNCTIONS 3. Use [왖] and [왔] to Exposure Compensation (EV Shift) change the exposure compensation value, and then press [SET]. Exposure compensation lets you change the exposure setting (EV value) manually to adjust for the lighting of your subject. This feature helps to achieve better results when recording a backlit subject, a strongly lit subject indoors, or a subject that is against a dark background. • Pressing [SET] registers the displayed value. EV value EV Shift Range: –2.
OTHER RECORDING FUNCTIONS • To cancel EV Shift, adjust the value until it becomes 0.0. Adjusting White Balance The wavelengths of the light produced by various light sources (sunlight, light bulb, etc.) can affect the color of a subject when it is recorded. White balance lets you make adjustments to compensate for different lighting types, so the colors of an image appear more natural. 4. Record the image.
OTHER RECORDING FUNCTIONS 3. Use [왖] and [왔] to select the setting you Adjusting White Balance Manually want, and then press [SET]. When shooting under these conditions: Normal conditions Under some light sources, automatic white balance under the “Auto” setting can take a long time to complete. Also, the auto white balance range (color temperature range) is limited. Manual white balance helps to ensure that colors are recorded correctly for a particular light source.
OTHER RECORDING FUNCTIONS 4. Point the camera at a white piece of paper or Using the BESTSHOT Mode similar object under the lighting conditions for which you want to set the white balance, and then press the shutter release button. Selecting one of the 21 BESTSHOT scenes automatically sets up the camera for recording a similar type of image. ■ Example Sample Scene • Portrait • Scenery • Night Scene • Night Scene Portrait A white piece of paper • This starts the white balance adjustment procedure.
OTHER RECORDING FUNCTIONS 1. In the REC mode, press [MENU]. IMPORTANT! • Sample scene number 4 is Coupling Shot scene (page 72). Sample scene number 5 is a Pre-shot scene (page 74). • BESTSHOT scenes were not recorded using this camera. They are provided as samples only. • Images recorded using a BESTSHOT scene may not produce the results you expected due to shooting conditions and other factors.
OTHER RECORDING FUNCTIONS 6. Use [왗] and [왘] to Creating Your Own BESTSHOT Setup display the image whose setup you want to register as a BESTSHOT scene. You can use the procedure below to save the setup of an image you recorded for later recall when you need it again. Recalling a setup you save automatically sets up the camera accordingly. 1. In the REC mode, press [MENU]. 7. Use [왖] and [왔] to 2. Select the “REC” tab, select “REC Mode”, and select “Save”, and then press [SET]. then press [왘]. 3.
OTHER RECORDING FUNCTIONS ■ To delete a BESTSHOT user setup IMPORTANT! • BESTSHOT user setups are located in the camera’s built-in memory after the built-in sample scenes. • When a BESTSHOT user setup is recalled, the monitor screen in step 4 of the procedure on page 69 displays the text “Recall User Scene”. • Note that formatting the built-in memory (page 132) deletes all BESTSHOT user setups. 1. In the REC mode, press [MENU]. 2. Select the “REC” tab, select “REC Mode”, and then press [왘]. 3.
OTHER RECORDING FUNCTIONS Combining Shots of Two People into a Single Image (Coupling Shot) • Combined Images The Coupling Shot mode lets you record images of two people and combine them into a single image. This makes it possible for you to include yourself in group images, even when there is no one else around to record the image for you. Coupling Shot is available in the BESTSHOT mode (page 68).
OTHER RECORDING FUNCTIONS 5. Align the focus frame on the monitor screen with the subject you want on the left side of the image, and then press the shutter release button to record the image. 6. Next, align the focus frame with the subject you want in the right side of the image, taking care to align the actual background with the semi-transparent image of the background of the first image, which is shown on the monitor screen. When everything is aligned correctly, record the image.
OTHER RECORDING FUNCTIONS • Freeze the background on the monitor screen. Recording a Subject onto an Existing Background Image (Pre-shot) Pre-shot helps you get the background you want, even if you need to ask someone else to record the image for you. Basically, Pre-shot is a two-step process. 1. You compose the background you want and press the shutter release button, which causes a semi-transparent image of the background to remain on the monitor screen. 2.
OTHER RECORDING FUNCTIONS 1. In the REC mode, press [MENU]. 6. Next, align the focus frame with the subject, composing the subject with the semi-transparent background shown on the monitor screen. When everything is aligned correctly, record the image. 2. Select the “REC” tab, select “REC Mode”, and then press [왘]. 3. Use [왖] and [왔] to select “ BESTSHOT”, and then press [SET]. 4. Use [왗] and [왘] to select “Pre-shot”, and then press [SET].
OTHER RECORDING FUNCTIONS 3. Use [왖] and [왔] to Using the Movie Mode You can record movies with audio, up to 60 seconds long. Movie”, select “ and then press [SET]. • File Format: AVI AVI format conforms to the Motion JPEG format promoted by the Open DML Group. • “Remaining capacity” shows how many 60second movies can still be recorded to memory. Remaining capacity • Image Size: 320 x 240 pixels • Movie File Size: Approximately 160KB/second.
OTHER RECORDING FUNCTIONS • The remaining recording time value counts down on the monitor screen as you record. — Operating camera buttons during recording can cause button noise to be included in the audio. — Movie audio is recorded in monaural. — The camera automatically switches to the Pan Focus mode (PF) (page 61) whenever you enter the Movie Mode. — The camera focuses automatically whenever you have Auto Focus (page 59) or Macro ( ) selected as the focus mode.
OTHER RECORDING FUNCTIONS 1. In the REC mode, press [MENU]. Recording Audio 2. Select the “REC” tab, select “REC Mode”, and Adding Audio to a Snapshot then press [왘]. You can add audio to a snapshot after you record it. 3. Use [왖] and [왔] to select “ • Image Format: JPEG JPEG is an image format that provides efficient data compression. The file extension of a JPEG file is “.JPG”. ( + )” and then press [SET]. • This enters the Snapshot Audio Mode. 4.
OTHER RECORDING FUNCTIONS 5. Press the shutter release button to start audio Recording Your Voice recording. The Voice Recording Mode provides quick and easy recording of your voice. • The green operation lamp flashes as recording is performed. • Audio Format: WAVE/ADPCM recording format This is the Windows standard format for audio recording. The file extension of a WAVE/ADPCM file is “.WAV”.
OTHER RECORDING FUNCTIONS ■ Audio Recording Precautions 4. Press the shutter release button to start voice recording. • Keep the microphone on the front of the camera pointed at the subject. • Take care that you do not block the microphone with your fingers. • The remaining recording time value counts down on the monitor screen and the green operation lamp flashes as recording is performed. • Pressing the [DISP] button during voice recording turns off the monitor screen.
OTHER RECORDING FUNCTIONS • When the histogram is too far to the left, it means that there are too many dark pixels. This type of histogram results when the overall image is dark. A histogram that is too far to the left may result in “black out” of the dark areas of an image. Using the Histogram You can use the [DISP] button to display a histogram on the monitor screen. The histogram lets you check exposure conditions as you record images (page 25).
OTHER RECORDING FUNCTIONS IMPORTANT! REC Mode Camera Settings • Note that the above histograms are shown for illustrative purposes only. You may not be able to achieve exactly the same shapes for particular subjects. • A centered histogram does not necessarily guarantee optimum exposure. The recorded image may be over-exposed or under-exposed, even though its histogram is centered. • You may not be able to achieve an optimum histogram configuration due to the limitations of EV shift.
OTHER RECORDING FUNCTIONS IMPORTANT! Specifying ISO Sensitivity • Increasing ISO sensitivity can cause static to appear inside an image. Select the ISO sensitivity setting that suits your shooting needs. • Using a high ISO sensitivity setting along with the flash to shoot a nearby subject may result in improper illumination of the subject. Use the following procedure to select the ISO sensitivity setting that suits the type of image you are recording. 1. In the REC mode, press [MENU]. 2.
OTHER RECORDING FUNCTIONS Turning the On-screen Grid On and Off Turning Image Review On and Off You can display gridlines on the monitor screen to help you compose images and ensure that the camera is straight when recording. Image review displays an image on the monitor screen as soon as you record it. Use the following procedure to turn image review on and off. 1. In the REC mode, press [MENU]. 2. Select the “REC” tab, select “Review”, and then press [왘]. 3.
OTHER RECORDING FUNCTIONS Assigning Functions to the [왗] and [왘] Keys A “key customization” feature lets you configure the [왗] and [왘] keys so they change camera settings whenever they are pressed in the REC mode. After you configure the [왗] and [왘] keys, you can change the setting assigned to them without going through the menu screen. 1. In the REC mode, press [MENU]. 2. Select the “REC” tab, select “L/R Key”, and then press [왘]. 3. Use [왖] and [왔] to select the setting you want, and then press [SET].
OTHER RECORDING FUNCTIONS Specifying Power On Default Settings Function On REC Mode The camera’s “mode memory” feature lets you specify the power on default settings individually for the REC mode, flash mode, focus mode, white balance mode, ISO sensitivity, AF Area, digital zoom mode, manual focus position and zoom position. Turning on mode memory for a mode tells the camera to remember the status of that mode when you turn off the camera, and restore it the next time you turn the camera back on.
OTHER RECORDING FUNCTIONS 1. In the REC mode, press [MENU]. Resetting the Camera 2. Select the “Memory” tab, select the item you Use the following procedure to reset all of the camera’s settings to their initial defaults as shown under “Menu Reference” on page 168. want to change, and then press [왘]. 3. Use [왖] and [왔] to select the setting you 1. In the REC mode or the PLAY mode, press want, and then press [SET]. [MENU].
PLAYBACK PLAYBACK 3. Use [ ] (forward) or [ ] (back) to scroll You can use the camera’s built-in monitor screen to view images after you record them. through files on the monitor screen. Basic Playback Operation Use the following procedure to scroll through files stored in the camera’s memory. NOTES 1. Press the power Power button • Holding down [ ] or [ ] scrolls images at high speed.
PLAYBACK IMPORTANT! Playing an Audio Snapshot • Audio volume can be adjusted only when playback is being performed or is paused. Perform the steps below to display an audio snapshot indicator) and play its audio. (indicated by a 1. In the PLAY mode, use [ ] and [ ] until the image you want is displayed. 2. Press [SET]. • This plays back the audio that accompanies the displayed image. • You can perform the following operations while audio is playing.
PLAYBACK 1. In the PLAY mode, use [ ] and [ ] to scroll Flipping the Display through images on the monitor screen and display the one you want. The following procedure flips the image 180 degrees. This comes in handy when you want to show someone standing in front of you an image on the monitor screen. 2. Press the shutter release button and [SET] at the same time. [SET] • This flips the image 180 degrees.
PLAYBACK 3. Use [ ], [ ], [ ], and [ ] to shift the image Zooming the Display Image up, down, left, or right. Perform the following procedure to zoom the image currently on the monitor screen up to four times its normal size. 4. Press [MENU] to return the image to its original size. 1. In the PLAY mode, use [ ] and [ ] to display IMPORTANT! the image you want. • You cannot enlarge a movie image.
PLAYBACK 4. Use [ ] and [ ] to select the setting you Resizing an Image want, and then press [SET]. You can use the following procedure to change a snapshot image to either SXGA size (1280 x 960 pixels) or VGA size (640 x 480 pixels). • VGA is the optimum image size for attachment to e-mail messages or incorporation into Web pages. 1. In the PLAY mode, press [MENU].
PLAYBACK 5. Use [ ], [ ], [ ], and [ ] to move the Cropping an Image cropping boundary up, down, left, or right until the area of the image you want to extract is within the boundary. Use the following procedure when you want to crop a portion of an enlarged image and use the remaining part of the image as an e-mail attachment, Web page image, etc. 6. Press [SET] to extract the part of the image 1. In the PLAY mode, use [ ] and [ ] to scroll enclosed in the cropping boundary.
PLAYBACK IMPORTANT! Playing a Movie • You cannot repeat play a movie. To play a movie more than once, repeat the steps of the above procedure. • This camera can also play back audio recordings. Note the following points when playing back audio. — Audio volume can be adjusted only when playback is being performed or is paused. Use the following procedure to play back a movie that was recorded in the movie mode. 1.
PLAYBACK Example: When there are 20 images in memory, and Image 1 is displayed first Displaying the 9-image View The following procedure displays nine images on the monitor screen at the same time. 1. In the PLAY mode, press the zoom button ( 18 19 6 7 8 15 16 17 20 1 2 9 10 11 18 19 20 3 4 5 12 13 14 1 2 3 ). 3.
PLAYBACK Selecting a Specific Image in the 9image View Displaying the Calendar Screen Use the following procedure to display a 1-month calendar. While the calendar is on the display, you can select a date, which displays the first image recorded on that date. This helps to make it easy to find the images you want. 1. Display the 9-image view. 2. Use [ ], [ ], [ ], and Selection boundary [ ] to move the selection boundary up, down, left, or right until it is located at the image you want to view. 1.
PLAYBACK • Pressing [ ] while the date selection cursor is located anywhere in the top line of the calendar causes the previous month to appear. Playing a Slide Show Slide Show automatically plays back images in sequence at a fixed interval. • Pressing [ ] while the date selection cursor is located anywhere in the bottom line of the calendar causes the next month to appear. • To exit the calendar screen, press [MENU] or the ( zoom button.
PLAYBACK 3. Configure the slideshow settings. IMPORTANT! • Note that all buttons are disabled while an image change is in progress. Wait until an image is stopped on the monitor screen before performing a button operation, or hold down the button until the image stops. • When the slideshow comes to a movie file, it plays the movie once and advances to the next file. • When the slideshow comes to an audio snapshot or voice recording file, it plays the audio once and then advances to the next file.
PLAYBACK ■ Selecting a Particular Image for a Slideshow To specify the slideshow images When you select “One image” as the slideshow type, the slide show displays only one image, without changing it. Use this setting when you want a particular image to remain on the display while the camera is on the USB cradle (Photo Stand feature). 1. Use [ ] and [ ] to select “Images”, and then press [ ]. 2. Use [ ] and [ ] to select the setting you want, and then press [SET]. To do this: Select this setting: 1.
PLAYBACK To specify the slideshow time To set the slideshow interval 1. Use [ ] and [ ] to select “Time”. 1. Use [ ] and [ ] to select “Interval”. 2. Use [ ] and [ ] to specify the time setting 2. Use [ ] and [ ] to specify the interval setting you want, and then press [SET]. you want, and then press [SET]. • You can specify a time in the range of 1 to 60 minutes. • You can specify “MAX”, or a value in the range of 1 to 30 seconds as the interval.
PLAYBACK 3. To stop the Phot Stand slideshow, press Using the Photo Stand Feature [PHOTO] again. The “Photo Stand” feature lets you specify what should appear on the camera’s monitor screen while the camera is on its USB cradle. You can play a Photo Stand slideshow without worrying about remaining battery power, or you can specify display of a particular image. Photo Stand feature operations are performed in accordance with slideshow setting.
PLAYBACK 4. Use [ ] and [ ] to Rotating the Display Image select “Rotate”, and then press [SET]. Use the following procedure to rotate the image 90 degrees and register the rotation information along with the image. After you do this, the image is always displayed in its rotated orientation whenever it appears during a slideshow (page 97) or on your computer screen. Note that the image is rotated automatically during a slideshow only.
PLAYBACK IMPORTANT! Using Image Roulette • Image Roulette does not play movie files or display voice recording images. • Image Roulette is disabled when there is only one snapshot image available. • Note that Image Roulette works only with images recorded with this camera. Image Roulette may not operate properly when other types of images are in memory. • If you do not start another Image Roulette operation for about one minute after the final image appears, the camera enters its normal PLAY mode.
PLAYBACK 1. In the PLAY mode, use [ ] and [ ] to scroll Adding Audio to a Snapshot through snapshots until the one to which you want to add audio is displayed. The “after-recording” feature lets you add audio to snapshots after they are recorded. You can also re-record an audio image (one with a icon on it). 2. Press [MENU]. • Audio Format: WAVE/ADPCM recording format This is the Windows standard format for audio recording. The file extension of a WAVE/ADPCM file is “.WAV”. 3.
PLAYBACK IMPORTANT! To re-record audio • Keep the microphone on the front of the camera pointed at the subject. • Take care that you do not block the microphone with your fingers. 1. In the PLAY mode, use [ ] and [ ] to scroll through snapshots until the one whose audio you want to re-record is displayed. 2. Select the “PLAY” tab, select “Dubbing”, and then press [ ]. Microphone 3. Use [ ] and [ ] to select “Delete”, and then press [SET].
PLAYBACK IMPORTANT! Playing Back a Voice Recording File • Audio volume can be adjusted only when playback is being performed or is paused. • If your recording has index marks (page 80) inside it, you can jump to the index mark before or after the current playback location by pausing playback and then pressing [ ] or [ ]. Next, press [SET] to resume playback from the index mark position. Perform the following steps to play back a voice recording file. 1.
DELETING FILES DELETING FILES You can delete a single file, or you can delete all files currently in memory. Deleting a Single File Perform the following steps when you want to delete a single file. IMPORTANT! • Note that file deletion cannot be undone. Once you delete a file, it is gone. Make sure you really do not need a file anymore before you delete it. Especially when deleting all files, make sure you check all the files you have stored before proceeding. • A protected file cannot be deleted.
DELETING FILES IMPORTANT! Deleting All Files • If a file cannot be deleted for some reason, the message “This function is not supported for this file.” appears when you try to delete it. The following procedure deletes all unprotected files currently in memory. 1. In the PLAY mode, press [ ] ( ). 2. Use [ ] and [ ] to select “All File Delete”, and then press [SET]. 3. Use [ ] and [ ] to select “Yes”. • To exit the file delete operation without deleting anything, select “No”. 4.
FILE MANAGEMENT FILE MANAGEMENT The file management capabilities of the camera make it easy to keep track of images. You can protect files against deletion, and even use its DPOF feature to specify images for printing. Each folder can hold files numbered up to 9,999. Trying to store the 10,000th file in a folder causes the next serially numbered folder to be created. Folder names are generated as shown below. Example: Name of the 26th file Folders CIMG0026.
FILE MANAGEMENT 4. Use [ ] and [ ] to Protecting Files select “On”, and then press [SET]. Once you protect a file it cannot be deleted (page 107). You can protect files individually or you can protect all files in memory with a single operation. • A file that is protected is indicated by the mark. To protect a single file • To unprotect a file, select “Off” in step 4, and then press [SET]. 1. In the PLAY mode, press [MENU]. 5. Press [MENU] to exit the menu screen. 2.
FILE MANAGEMENT To protect all files in memory DPOF The letters “DPOF” stand for “Digital Print Order Format”, which is a format for recording on a memory card or other medium which digital camera images should be printed and how many copies of the image should be printed. Then you can print on a DPOF-compatible printer or at a professional print service in accordance with the file name and number of copies settings recorded on the card.
FILE MANAGEMENT 5. Use [ ] and [ ] to specify the number of To configure print settings for a single image copies. • You can specify up to 99 for the number of copies. Specify 00 if you do not want to have the image printed. 1. In the PLAY mode, press [MENU]. 2. Select the “PLAY” tab, 6. To turn on date stamping for the prints, press select “DPOF”, and then press [ ]. [DISP] so 12 1 is displayed. • To turn off date stamping for the prints, press [DISP] so is not displayed.
FILE MANAGEMENT 5. To turn on date stamping for the prints, press To configure print settings for all images [DISP] so 1. In the PLAY mode, press [MENU]. 12 1 is displayed. • To turn off date stamping for the prints, press [DISP] so is not displayed. 12 2. Select the “PLAY” tab, select “DPOF”, and 1 6. After all the settings are the way you want, then press [ ]. press [SET] to apply them. 3. Use [ ] and [ ] to select “All images”, and then press [ ]. 4.
FILE MANAGEMENT PRINT Image Matching II Exif Print Images include PRINT Image Matching II data (mode setting and other camera setup information). A printer that supports PRINT Image Matching II reads this data and adjusts the printed image accordingly, so your images come out just the way you intended when you recorded them. Exif Print is an internationally supported, open standard file format that makes it possible to capture and display vibrant digital images with accurate colors. With Exif 2.
FILE MANAGEMENT 1. Use the DPOF procedure on page 111 to Using USB DIRECT-PRINT specify the images in file memory that you want to print. Your camera supports USB DIRECT-PRINT, which was developed by Seiko Epson Corporation. When connected directly to a printer that supports USB DIRECT-PRINT, you can select images to be printed and start the print operation directly from the camera. DPOF settings (page 111) are used to determine which images and how many copies should be printed. 2.
FILE MANAGEMENT 6. Press the USB cradle IMPORTANT! [USB] button. • See the documentation that comes with your printer for information about print quality and paper settings. • Contact your printer manufacturer for information about models that support USB DIRECT-PRINT, upgrades, etc. • Never disconnect the USB cable, or perform any camera or USB cradle operation while printing is in progress. Doing so causes a printer error.
FILE MANAGEMENT 3. Use [ ] and [ ] to Using the FAVORITE Folder select “Save”, and then press [SET]. You can copy scenery shots, photos of your family, or other special images from a file storage folder (page 151) to the FAVORITE folder in built-in memory (page 151). Images in the FAVORITE folder are not displayed during normal playback, so it helps to keep your personal image private as you carry them around.
FILE MANAGEMENT NOTES To display a file in the FAVORITE folder • Copying an image file with the above procedure creates a 320 x 240-pixel QVGA-size image in the FAVORITE folder. • A file copied into the FAVORITE folder is automatically assigned a file name that is a serial number. Though the serial number starts from 0001 and can go as high as 9999, the actual upper end of the range depends on built-in memory capacity.
FILE MANAGEMENT NOTE To delete a file from the FAVORITE folder • Holding down [ ] or [ ] scrolls images at high speed. 1. In the PLAY mode, press [MENU]. IMPORTANT! 2. Select the “PLAY” tab, select “Favorites”, and • Note that a FAVORITE folder is created in the camera’s built-in memory only. No FAVORITE folder is created on a memory card when you use one.
FILE MANAGEMENT IMPORTANT! To delete all files from the FAVORITE folder • You cannot use the delete operations on page 107 to delete images from the FAVORITE folder. Performing the memory format operation (page 132), however, does delete FAVORITE folder files. 1. In the PLAY mode, press [MENU]. 2. Select the “PLAY” tab, select “Favorites”, and then press [ ]. 3. Use [ ] and [ ] to select “Show”, and then press [SET]. 4. Press [ ] ( ). 5.
OTHER SETTINGS OTHER SETTINGS 4. Use [ ] and [ ] to change the setting, and Configuring Sound Settings then press [SET]. You can configure different sounds to play whenever you turn on the camera, press the shutter release button halfway or all the way, or perform a key operation. To configure sound settings To do this: Select this setting: Select a built-in sound Sound 1 through Sound 5 Turn off the sound Off NOTE 1.
OTHER SETTINGS To set the volume level Specifying an Image for the Startup Screen You can specify an image you recorded as the startup screen image, which causes it to appear on the monitor screen for about two seconds whenever you turn on the camera while the mode selector is aligned with “REC”. 1. In the REC mode or the PLAY mode, press [MENU]. 2. Select the “Set Up” tab, select “Sounds”, and then press [ ]. 1. In the REC mode or the PLAY mode, press [MENU]. 3. Use [ ] and [ ] to select “Volume”.
OTHER SETTINGS IMPORTANT! Configuring Power Down Image Settings • You can select any one of the following types of image as the startup image. — The camera’s built-in startup image — A snapshot you recorded with the camera — An audio snapshot you recorded with the camera — A movie you recorded with the camera 200KB or less in size • The snapshot image or movie that you select as the startup image is stored in a special memory location called “startup image memory”.
OTHER SETTINGS 3. Change the name of the file to one of the IMPORTANT! following. • Only a snapshot (JPEG) or movie (AVI) file can be used as the power down image. • Note that the Power Down Image feature works only with images recorded with this camera. The Power Down Image feature may not operate properly when another type of image is specified as the power down image. • Formatting the camera’s Flash memory deletes the power down image.
OTHER SETTINGS ■ To cancel Power Down Image settings Specifying the File Name Serial Number Generation Method 1. Use the USB cable to connect the camera to Use the following procedure to specify the method for generating the serial number used for file names (page 109). your computer (page 140). 2. Change the name of the current power down 1. In the REC mode or the PLAY mode, press image from ENDING.JPG or ENDING.AVI to something else, or delete the current power down image from Flash memory.
OTHER SETTINGS 5. Press [DISP]. Using the Alarm • You could press [SET] in place of [DISP] if you want to configure the alarm without an image. You can configure up to three alarms that cause the camera to beep and display a specified image at the time you specify. 6. Use [ ] and [ ] to select the scene you want to appear at the alarm time, and then press [SET]. To set an alarm 7. After all the settings are the way you want, 1. In the PLAY mode, press [MENU]. press [SET]. 2.
OTHER SETTINGS Stopping the Alarm Setting the Clock When an alarm time is reached while the camera is turned off, the alarm will sound for about one minute (or until you stop it), and then the camera will turn on. To stop the alarm after it starts to sound, press any button. If the camera is on the USB cradle when an alarm sounds, you can stop it by pressing the USB cradle [USB] button or [PHOTO] button, or any camera button.
OTHER SETTINGS 4. Use [ ] and [ ] to select “City”, and then To set the current time and date press [ ]. 1. In the REC mode or the PLAY mode, press 5. Use [ ], [ ], [ ], and [ ] to select the [MENU]. geographical area that contains location you want to select as your Home Time zone, and then press [SET]. 2. Select the “Set Up” tab, select “Adjust”, and then press [ ]. 6. Use [ ] and [ ] to select the city you want, 3. Set the current date and the time. and then press [SET]. 7.
OTHER SETTINGS Changing the Date Format Using World Time You can select from among three different formats for display of the date. You can use the World Time screen to view a time zone that is different from the home time zone when you go on a trip, etc. World Time can display the time in one of 162 cities in 32 time zones. 1. In the REC mode or the PLAY mode, press [MENU]. To display the World Time screen 2. Select the “Set Up” tab, select “Date Style”, and then press [ ]. 1.
OTHER SETTINGS 6. Use [ ] and [ ] to To configure World Time settings select the city you want, and then press [SET]. 1. In the REC mode or the PLAY mode, press [MENU]. • This displays the current time in the city you select. 2. Select the “Set Up” tab, select “World Time”, and then press [ ]. • This displays the current World Time zone. 7. When the setting is the way you want, press [SET] to apply it and exit the setting screen. 3. Use [ ] and [ ] to select “World”, and then press [ ]. 4.
OTHER SETTINGS 6. After the setting is the way you want, press To configure summer time (DST) settings [SET]. • This displays the current time in accordance with your setting. 1. In the REC mode or the PLAY mode, press [MENU]. 7. Press [SET] again to exit the setting screen. 2. Select the “Set Up” tab, select “World Time”, and then press [ ]. • This displays the current World Time Settings. 3. Use [ ] and [ ] to select “World”, and then press [ ].
OTHER SETTINGS Changing the Display Language Formatting Built-in Memory You can use the following procedure to select one of ten language as the display language. Formatting built-in memory deletes any data stored in it. IMPORTANT! 1. In the REC mode or the PLAY mode, press • Note that data deleted by a format operation cannot be recovered. Check to make sure you do not need any of the data in memory before you format it.
OTHER SETTINGS 4. Use [ ] and [ ] to select “Format”, and then press [SET]. • To exit the format operation without formatting, select “Cancel”.
USING A MEMORY CARD USING A MEMORY CARD You can expand the storage capabilities of your camera by using a commercially available memory card (SD memory card or MultiMediaCard). You can also copy files from built-in flash memory to a memory card and from a memory card to flash memory. IMPORTANT! • Use only an SD memory card or a MultiMediaCard with this camera. Proper operation is not guaranteed when any other type of card is used.
USING A MEMORY CARD 2. Positioning the memory Using a Memory Card card so its front is facing in the same direction as the camera’s monitor screen, carefully slide it into the card slot. IMPORTANT! • Make sure you turn off the camera before inserting or removing a memory card. • Be sure to orient the card correctly when inserting it. Never try to force a memory card into the slot when you feel resistance. To insert a memory card into the camera 1.
USING A MEMORY CARD To remove a memory card from the camera Formatting a Memory Card Formatting a memory card deletes any data already stored on it. 1. Press the memory card into IMPORTANT! the camera and then release it. This will cause the card to come part way out of the camera. • Be sure to use the camera to format a memory card. Formatting a memory card on a computer and then using it in the camera can slow down data processing by the camera.
USING A MEMORY CARD 1. Load the memory card into the camera. Memory Card Precautions 2. Turn on the camera. Next, enter the REC • If a memory card starts to behave abnormally, you can restore normal operation by reformatting it. However, we recommend that you always take along more than one memory card whenever using the camera far away from the home or office.
USING A MEMORY CARD 4. Use [ ] and [ ] to select “Built-in Copying Files Card”, and then press [SET]. Use the procedures below to copy files between built-in memory and a memory card. • This starts the copy operation and displays the message “Busy.... Please wait...”. • After the copy operation is complete, the monitor screen shows the last file in the folder. IMPORTANT! • Only snapshot, movie files, audio snapshot, and voice recording files recorded with this camera can be copied.
USING A MEMORY CARD NOTE To copy a file from a memory card to built-in memory • Files are copied to the folder in built-in memory whose name has the largest number. With this procedure you can copy one file at a time. 1. Perform steps 1 through 3 of the procedure under “To copy all the files in built-in memory to a memory card”. 2. Use [ ] and [ ] to select “Card Built-in”, and then press [SET]. 3. Use [ ] and [ ] to select the file you want to copy. 4.
VIEWING IMAGES ON A COMPUTER VIEWING IMAGES ON A COMPUTER After using the USB cradle to establish a USB connection between the camera and your computer, you can use your computer to view images in file memory and copy images to your computer’s hard disk or other storage media. In order to do this, you first need to install the USB driver located on the CD-ROM that comes bundled with the camera onto your computer.
VIEWING IMAGES ON A COMPUTER 3. On the menu screen that appears, click IMPORTANT! “English”. • Do not try to establish a connection between the camera and computer before installing the USB driver onto the computer. • If you want to transfer files from the camera’s built-in memory to a computer, make sure there is no memory card loaded in the camera before you place it onto the USB cradle. 4. Click [USB driver] and then [Install]. • This starts installation.
VIEWING IMAGES ON A COMPUTER 6. Connect the bundled AC adaptor to the [DC IN 7. Connect the USB cable that comes bundled 5.3V] connector of the USB cradle, and then plug it in to a household power outlet. with the camera to the USB cradle and your computer’s USB port. USB port [DC IN 5.3V] USB cable (bundled) Connector B Connector A [USB] • Take care when connecting the USB cable to the USB cradle or your computer. USB ports and cable plugs are shaped for proper positioning.
VIEWING IMAGES ON A COMPUTER 8. After making sure the camera is turned off, 9. Press the USB cradle’s [USB] button. place the camera onto the USB cradle. • This will cause the “Add New Hardware...” dialog box to appear on the computer screen as the computer automatically detects the camera’s file memory. After you install the USB driver, “Add New Hardware...” dialog box will no longer appear when you perform the above steps to establish a USB connection.
VIEWING IMAGES ON A COMPUTER 10. On your computer, double-click “My IMPORTANT! Computer”. • Never use your computer to edit, delete, move, or rename images stored in file memory. Doing so can cause problems with the image management data used by the camera, which may make it impossible to display images on the camera or it may cause a large error in the number of images value displayed by the camera.
VIEWING IMAGES ON A COMPUTER USB Connection Precautions Using the Camera with a Macintosh Computer • Be sure to read the documentation that comes with your computer for other important information about USB connections. • Be sure to connect the AC adaptor to the USB cradle to supply power to the camera. • USB data communication is performed regardless of the current setting of the camera’s mode selector. • Do not leave the same image displayed on your computer screen for a long time.
VIEWING IMAGES ON A COMPUTER 1. Connect the bundled AC adaptor to the [DC IN IMPORTANT! 5.3V] connector of the USB cradle, and then plug it in to a household power outlet. • If you want to transfer files from the camera’s built-in memory to a computer, make sure there is no memory card loaded in the camera before you place it onto the USB cradle. [DC IN 5.
VIEWING IMAGES ON A COMPUTER 2. Connect the USB cable that comes bundled 3. After making sure the camera is turned off, with the camera to the USB cradle and your computer’s USB port. USB port USB cable (bundled) place the camera onto the USB cradle. • Do not place the camera onto the USB cradle while it is turned on. Connector B PLAY REC MEN Connector A U SET DISP PHOT O CHAR GE [USB] USB [USB] button [USB] lamp • Take care when connecting the USB cable to the USB cradle or your computer.
VIEWING IMAGES ON A COMPUTER 4. Press the USB cradle’s [USB] button. 8. To copy all the files in file memory to your Macintosh hard disk, drag the “DCIM” folder to the folder to which you want to copy it. • Pressing the [USB] button enters the USB mode, which causes the USB cradle’s [USB] lamp to light green (page 172). IMPORTANT! 5. Your Macintosh will see the camera’s file • Never use your computer to edit, delete, move, or rename images stored in file memory.
VIEWING IMAGES ON A COMPUTER USB Connection Precautions Operations You Can Perform from Your Computer • Be sure to read the documentation that comes with your computer for other important information about USB connections. • Be sure to connect the AC adaptor to the USB cradle to supply power to the camera. • USB data communication is performed regardless of the current setting of the camera’s mode selector. • Do not leave the same image displayed on your computer screen for a long time.
VIEWING IMAGES ON A COMPUTER Using a Commercially Available SD Memory Card Reader/Writer See the user documentation that comes with the SD memory card reader/writer for details about how to use it. Using a Memory Card to Transfer Images to a Computer The procedures in this section describe how to transfer images from the camera to your computer using a memory card. Using a Computer with a Built-in SD Memory Card Slot Insert the SD memory card directly into the slot.
VIEWING IMAGES ON A COMPUTER Memory Directory Structure Memory Data Images recorded with this camera and other data are stored in memory using DCF (Design rule for Camera File System) protocol. DCF protocol is designed to make it easier to exchange image and other data between digital cameras and other devices. ■ Directory Structure <¥DCIM¥> 100CASIO CIMG0001.JPG CIMG0002.AVI CIMG0003.WAV CIMG0004.JPG CIMG0004.
VIEWING IMAGES ON A COMPUTER ■ Folder and File Contents • FAVORITE folder Folder that contains Favorites image files (Image Size: 320 x 240 pixels) • DCIM folder Folder that stores all of the digital camera files • DPOF file folder Folder that contains DPOF files • Storage folder Folder for storing files created by the digital camera • BESTSHOT folder (Built-in memory only) Folder that contains BESTSHOT user setup files.
VIEWING IMAGES ON A COMPUTER Image Files Supported by the Camera Built-in Memory and Memory Card Precautions • Image files recorded with the CASIO EX-Z4 Digital Camera • DCF protocol image files • Note that the folder named “DCIM” is the parent (top) folder of all the files in memory. When transferring memory contents to a hard disk, CD-R, MO disk, or other external storage, treat all the contents inside a DCIM folder as a set and always keep them together.
USING THE CAMERA WITH A COMPUTER USING THE CAMERA WITH A COMPUTER The album feature of the camera creates files that make it possible for you to view images on your computer in a photo album layout. You can also use the applications contained on the CD-ROM that comes bundled with the camera to automate image transfer and to retouch images. • You can use the Web browser shown below to view or print the contents of an album.
USING THE CAMERA WITH A COMPUTER • Creating an album causes a file folder named “ALBUM”, which contains a file named “INDEX.HTM” plus other files to be created in camera memory or on the memory card. Selecting an Album Layout IMPORTANT! 1. In the PLAY mode, press [ ] ( You can select from among 10 different display layouts for an album. • Never open the battery compartment cover or remove the memory card from the camera while an album is being created.
USING THE CAMERA WITH A COMPUTER Configuring Detailed Album Settings ■ Background Color 1. In the PLAY mode, press [ ] ( You can specify white, black, or gray as the color of the album background using the procedure under “Configuring Detailed Album Settings”. ). 2. Use [ ] and [ ] to select “Set Up”, and then press [ ]. ■ Album Type 3. Use [ ] and [ ] to There are two album types: “Normal” and “Index/Info”. select the item whose setting you want to change, and then press [ ].
USING THE CAMERA WITH A COMPUTER ■ Image Use ■ Auto Album Creation On/Off This setting lets you select from among three different image uses, as described below. Select the image use that best suits the way you plan to use the image. This setting controls whether an album is created automatically whenever you turn off the camera.
USING THE CAMERA WITH A COMPUTER NOTE Viewing Album Files • Depending on the number of images in memory, it can take quite a bit of time to complete auto album creation when you turn off the camera. If you do not plan to use the album feature, we suggest that you keep auto album creation turned off, which shortens the amount of time the camera takes to power down completely. You can view and print album files using your computer’s Web browser application. 1.
USING THE CAMERA WITH A COMPUTER 4. If you created the album after selecting “Normal” type or “Index/Info” as the album type under “Configuring Detailed Album Settings” on page 156, you can click one of the following display options. Album : Displays an album created by the camera. Index : Displays a list of images stored in a folder. Info : Displays information about each image.
USING THE CAMERA WITH A COMPUTER • The following describes the information that appears on the Info Screen. This Info Screen item: File Size Resolution Quality Drive mode AE Light metering Shutter speed Aperture stop Exposure comp Focusing mode Flash mode AF Area Sharpness Saturation Contrast White balance Sensitivity Filter Enhancement Flash intensity Digital zoom World Date Model NOTES • When printing an album page, you should set up your Web browser as described below.
USING THE CAMERA WITH A COMPUTER Saving an Album Installing the Software from the CD-ROM • To save an album, copy the “DCIM” folder from camera memory or the memory card to your computer’s hard disk, a CD-R, an MO disk, or some other storage medium. Note that copying only the “ALBUM” folder, does not copy image data and other necessary files. • After copying the “DCIM” folder, do not change or delete any of the files inside of it.
USING THE CAMERA WITH A COMPUTER DirectX (for Windows) This software provides an extended tool set including a codec that allows Windows 98 and 2000 to handle movie files recorded using a digital camera. You do not need to install DirectX if you are running Windows XP or Me. Computer System Requirements Computer system requirements depend on each of the applications, as described below. Windows Acrobat Reader (for Windows) This is an application that lets you read PDF files.
USING THE CAMERA WITH A COMPUTER Getting Started Installing Software from the CD-ROM in Windows Start up your computer and insert the CD-ROM into its CDROM drive. This will automatically launch the menu application, which displays a menu screen on your computer. Use the procedures in this section to install the software from the bundled CD-ROM to your computer. NOTE • The menu application may not start up automatically on some computers. If this happens, navigate to the CDROM and double-click “menu.
USING THE CAMERA WITH A COMPUTER Viewing the Contents of the “Read me” File Installing an Application 1. Click the “Install” button for the application You should always read the “Read me” file for any application before installing it. The “Read me” file contains information you need to know when installing the application. you want to install. 2. Follow the instructions that appear on your computer screen. 1. Click the “Read me” button for the application IMPORTANT! you are going to install.
USING THE CAMERA WITH A COMPUTER Viewing User Documentation (PDF Files) User Registration 1. In the “Manual” area, click the name of the manual you want to read. You can perform user registration over the Internet. To do so, of course, you need to be able to connect to the Internet with your computer. IMPORTANT! 1. Click the “Register” button. • You need to have Adobe Acrobat Reader installed on your computer to read user documentation files.
USING THE CAMERA WITH A COMPUTER ■ To install Photo Loader Installing Software from the CD-ROM on a Macintosh 1. Open the folder named “Photo Loader”. Use the procedures in this section to install the software from the bundled CD-ROM to your computer. 2. Open the folder named “English”, and then open the file named “Important”. Installing Software 3. Open the folder named “Installer”, and then Use the following procedures to install the software. open the file named “readme”. 4.
USING THE CAMERA WITH A COMPUTER ■ To read the Photo Loader user’s guide Viewing User Documentation (PDF Files) To perform the following procedures, you must have Acrobat Reader installed on your Macintosh. You can download the latest version of Adobe Acrobat Reader by visiting the Adobe Systems website. 1. On the CD-ROM, open the “Manual” folder. 2. Open the “Photo Loader” folder and then open the “English” folder. ■ To view the camera user’s guide 3. Open “PhotoLoader_english”. 1.
APPENDIX APPENDIX L/R Key Menu Reference The following shows lists of menus that appear in the REC mode and PLAY mode, and their settings. • The settings that are underlined in the following table are initial defaults.
APPENDIX ■ PLAY mode ● Set Up tab menu Sounds Startup / Half Shutter /Shutter / Operation / Volume Startup File No. On (Selectable image) / Off Continue / Reset World Time Home / World Home Time setup (city, DST, etc.) Date Style World Time setup (city, DST, etc.
APPENDIX ● Set Up tab menu Indicator Lamp Reference Sounds Startup / Half Shutter / Shutter / Operation / Volume Startup File No. On (Selectable image) / Off Continue / Reset World Time Home / World Home Time setup (city, DST, etc.) Date Style World Time setup (city, DST, etc.
APPENDIX REC mode Operation Lamp Self-timer Operation Lamp Lamp Green Red Green Meaning Red Operational (Power on, recording Lit enabled) Flash is charging. Pattern 3 Lit Pattern 3 Lit Cannot Auto Focus. Monitor screen is off. Pattern 2 Pattern 1 Storing image Storing movie Pattern 1 Self-timer countdown (10 to 3 seconds) Pattern 2 Self-timer countdown (3 to 0 seconds) Pattern 1 Cannot charge flash. Memory card problem / Memory Pattern 2 card is unformatted.
APPENDIX PLAY mode Operation Lamp Green Red USB Cradle Indicator Lamps Self-timer Lamp The USB cradle has two indicator lamps: a [CHARGE] lamp and a [USB] lamp. These lamps light and flash to indicate the current operational status of the USB cradle and camera.
APPENDIX Troubleshooting Guide Symptom Possible Cause Power does not turn on. 1) The battery is not oriented correctly. 2) The battery is dead. 1) Orient the battery correctly (page 26). 2) Charge the battery (page 28). If the battery goes dead soon after being charged, it means the battery has reached the end of its life and needs to be replaced. Purchase a separately available NP-20 rechargeable lithium ion battery. Camera suddenly powers down. 1) Auto Power Off activated (page 37).
APPENDIX Playback Image Recording Symptom Possible Cause Action The subject is out of focus in the recorded image. The image is not focused properly. When composing the image, make sure the subject on which you want to focus is located inside the focus frame. Camera powers down during self-timer countdown. The battery is dead. Charge the battery (page 28). Monitor screen image is out of focus. 1) You are using the Manual Focus Mode and have not focused the image.
APPENDIX Possible Cause Action A memory card with non-DCF images recorded with another camera is loaded in the camera. This camera cannot display non-DCF images recorded onto a memory card using another digital camera. All buttons and switches are disabled. Circuit problem caused by electrostatic charge, impact, etc. while the camera was connected to another device. Remove the battery from the camera, reinsert it, and then try again. Monitor screen is off. 1) USB communication is in progress.
APPENDIX Display Messages Alarm setting complete. This message appears after you change the alarm setting. Battery is low. The battery is dead. Can not find the file. The camera cannot find the image specified by the slideshow “Images” setting. Specify another image (page 99). Cannot register any more files. Card ERROR • You are attempting to register a BESTSHOT setup when the “SCENE” folder already contains 999 setups.
APPENDIX The card is locked. The LOCK switch of the SD memory card is locked. You cannot store images to or delete images from a memory card that is locked. There are no files. There are no files in built-in memory or on the memory card. Specifications Main Specifications Product ............................... Digital Camera Model .................................. EX-Z4 There are no printing There are no DPOF settings specifying images and images. the number of copies of each for printing.
APPENDIX Approximate Memory Capacity and File sizes: Delete .................................. Single-file, all files (with protection) • Snapshots File Size (pixels) 2304 x 1728 2304 x 1536 (3:2) 1600 x 1200 (UXGA) 1280 x 960 (SXGA) 640 x 480 (VGA) Effective Pixels .................. 4.0 million Quality Approximate Built-in flash Image File Size memory 10MB Fine Normal Economy Fine Normal Economy Fine Normal Economy Fine Normal Economy Fine Normal Economy 1.9MB 1.5MB 1.1MB 1.8MB 1.4MB 1.
APPENDIX Aperture .............................. F2.6/4.3, auto switching Date and Time ................ Recorded with image data Auto Calendar ................. To 2049 World Time ...................... City; Date; Time; Summer time; 162 cities in 32 time zones White Balance .................... Automatic, fixed (4 modes), manual switching Self-timer ............................ 10 seconds, 2 seconds, Triple Selftimer Input/Output Terminals .... Cradle connector Microphone ........................
APPENDIX ■ Rechargeable Lithium Ion Battery (NP-20) *2 Normal Recording Conditions • Temperature: 23°C (73°F) • Monitor screen: On • Zoom operation between full wide to full telephoto every 30 seconds, during which two images are recorded, one image with flash; power turned off and back on every time 10 images are recorded. Rated Voltage .................... 3.7 V Rated Capacitance ............ 680 mAh Operating Temperature Range ..................................
APPENDIX ■ Special AC Adaptor (AD-C51G) Power Requirement .......... 100 to 240V AC, 50/60Hz, 83 mA Output ................................. 5.3V DC, 650 mA Dimensions ........................ 78(W) x 20(H) x 39(D) mm (3.1˝(W) x 0.78˝(H) x 1.5˝(D)) (excluding projections and cable) Weight ................................. Approximately 90 g (3.2 oz) Power Supply • Use only the special NP-20 rechargeable lithium ion battery to power this camera. Use of any other type of battery is not supported.
