E Digital Camera EX-Z4 User’s Guide Thank you for purchasing this CASIO Product. • Before using it, be sure to read the precautions contained in this User’s Guide. • Keep the User’s Guide in a safe place for future reference. • For the most up-to-date information about this product, visit the official Exilim Website at http://www.exilim.com/.
INTRODUCTION INTRODUCTION Unpacking Check to make sure that all of the items shown below are included with your camera. If something is missing, contact your dealer as soon as possible. PHOTO CHARGE USB Camera Rechargeable lithium ion battery (NP-20) USB Cradle (CA-21A) Strap CD-ROM USB Cable * The shape of the AC power cord plug varies according to country or geographic area.
INTRODUCTION 19 Contents GETTING READY About This Manual ..................................................... 19 2 General Guide ............................................................ 20 INTRODUCTION Camera USB Cradle Unpacking .................................................................... 2 Monitor Screen Contents ........................................... 22 Features .......................................................................
INTRODUCTION 44 Exposure Compensation (EV Shift) ........................... 65 BASIC IMAGE RECORDING Adjusting White Balance ............................................ 66 Recording an Image ................................................... 44 Aiming the Camera Recording an Image Recording Precautions About Auto Focus About the REC Mode Monitor Screen Adjusting White Balance Manually 67 44 45 47 48 48 Using the BESTSHOT Mode .....................................
INTRODUCTION 88 PLAYBACK 107 Basic Playback Operation .......................................... 88 Playing an Audio Snapshot DELETING FILES Deleting a Single File ............................................... 107 89 Deleting All Files ...................................................... 108 Flipping the Display .................................................... 90 Zooming the Display Image ....................................... 91 109 FILE MANAGEMENT Resizing an Image ...................
INTRODUCTION 121 OTHER SETTINGS 134 Configuring Sound Settings ..................................... 121 To configure sound settings To set the volume level Using a Memory Card .............................................. 135 121 122 To insert a memory card into the camera To remove a memory card from the camera Formatting a Memory Card Memory Card Precautions Specifying an Image for the Startup Screen ........... 122 Configuring Power Down Image Settings ................
INTRODUCTION 154 USING THE CAMERA WITH A COMPUTER 168 Using the Album Feature ......................................... 154 Creating an album Selecting an Album Layout Configuring Detailed Album Settings Viewing Album Files Saving an Album Menu Reference ....................................................... 168 154 155 156 158 161 Indicator Lamp Reference .......................................
INTRODUCTION • The USB driver (mass storage) uses Phoenix Technologies Ltd. software. Compatibility Software Copyright C 1997 Phoenix Technologies Ltd., All Rights Reserved. • Other company, product and service names used herein may also be trademarks or service marks of others. • Photo Loader and Photohands are the property of CASIO COMPUTER CO., LTD. Except as stipulated above, all copyrights and other related rights to these applications revert to CASIO COMPUTER CO., LTD.
INTRODUCTION • Easy Image Transfer Transfer images to a computer simply by placing the camera onto the USB cradle. Features • 4.0 million Effective Pixels A high-resolution megapixel CCD provides 4.0 million effective pixels (4.23 million total pixels) for images that print beautifully. • Photo Stand feature A slideshow of images in file memory can be played while the camera is on its USB cradle. • 2.
INTRODUCTION • Movie + Audio Mode • Real-time histogram An on-screen histogram lets you adjust exposure as you view the effect on overall image brightness, which makes shooting under difficult lighting conditions easier than ever before. • Voice Recording Quick and easy recording of voice input. • After Recording Adds audio to images after they are recorded. • World Time A simple operation sets the current time for your current location. You can select from among 162 cities in 32 time zones.
INTRODUCTION • USB DIRECT-PRINT support Your camera supports USB DIRECT-PRINT, which was developed by Seiko Epson Corporation. When connected directly to a printer that supports USB DIRECT-PRINT, you can select images to print and start the print operation directly from the camera. Precautions General Precautions Be sure to observe the following important precautions whenever using the EX-Z4.
INTRODUCTION • Never fire the flash while it is too close to the subject’s eyes. Intense light from the flash can cause eye damage if it is fired too close to the eyes. This is especially true with young children. When using the flash, the camera should be at least one meter (3.3´) from the eyes of the subject. • Keep the camera away from water and other liquids, and never let it get wet. Moisture creates the danger of fire and electric shock.
INTRODUCTION Data Error Precautions Operating conditions • Your digital camera is manufactured using precision digital components. Any of the following creates the risk of corruption of data in file memory. • This camera is designed for use in temperatures ranging from 0°C to 40°C (32°F to 104°F). • Do not use or keep the camera in the following areas.
INTRODUCTION Condensation Lens • When you bring the camera indoors on a cold day or otherwise expose it to a sudden change of temperature, there is the possibility that condensation can form on the exterior or on interior components. Condensation can cause malfunction of the camera, so you should avoid exposing it to conditions that might cause condensation.
QUICK START GUIDE QUICK START GUIDE First, charge the battery! 1. Load the battery (page 26). 2. Place the camera onto the USB cradle to charge the battery (page 28). 1 • It takes about two hours to achieve a full charge.
QUICK START GUIDE To configure display language and clock settings • Be sure to configure the following settings before using the camera to record images. (See page 40 for details.) 1. Press the power button to turn on the camera. 2. Press [ ] to select the language you want. 1 3. Press [SET] to register the language setting. 4. Use [ ], [ ], [ ], and [ ] to select the geographical PLAY REC MENU SET DISP 2, 3, 4, 5, 6, 7, 8, 9 area you want, and then press [SET]. 5.
QUICK START GUIDE To record an image To view a recorded image (See page 44 for details.) Green operation lamp 2 1 4 (See page 88 for details.) 2 1 99 1600 1200 NORMAL IN 1 / 1000 F2.6 PLAY 03/12 03 12/24 24 12:58 12 58 PLAY REC REC MENU MENU SET 3 SET Focus frame DISP DISP 3 1. Press the power button to turn on the camera. 1. Press the power button to turn on the camera. 2. Align the mode selector with “REC”. 3.
QUICK START GUIDE To delete an image (See page 107 for details.) 2 1 PLAY REC MENU SET DISP 3, 4, 5, 6 1. Press the power button to turn on the camera. 2. Align the mode selector with “PLAY”. 3. Press [ ] ( ). 4. Use [ ] and [ ] to display the image you want to delete. 5. Use [ ] and [ ] to select “Delete”. • To exit the image delete operation without deleting anything, select “Cancel”. 6. Press [SET] to delete the image.
GETTING READY GETTING READY ■ Button Operations This section contains information about things you need to know about and do before trying to use the camera. Button operations are indicated by the button name inside of brackets ([ ]). About This Manual ■ On-screen Text This section contains information about the conventions used in this manual. On-screen text is always enclosed by double quotation marks (“ ”).
GETTING READY General Guide The following illustrations show the names of each component, button, and switch on the camera.
GETTING READY ■ Bottom USB Cradle Simply placing your CASIO digital camera onto the USB cradle lets you perform the following tasks. • Battery charging (page 28) • Automatic transfer of images to a computer (page 140) • Viewing of images using the Photo Stand slideshow feature (page 101). H I J ■ Front H Battery compartment cover I Connector J Tripod screw hole 12 3 * Use this hole when attaching to a tripod.
GETTING READY Monitor Screen Contents The monitor screen uses various indicators and icons to keep you informed of the camera’s status. REC mode 1 2 34 5 1 Flash Mode indicator 6 None Auto 4 Self-timer None Flash Off C 7 Flash On 8 Red-eye reduction 9 0 • If the camera detects that flash is required while auto flash is selected, the flash on indicator will appear when the shutter release button is pressed half way.
GETTING READY D D Digital zoom indicator E Shutter speed value E F G • An out of range aperture or shutter speed causes the corresponding monitor screen value to turn amber. F Aperture value G ISO sensitivity H H Zoom indicator • Left side indicates optical zoom. • Right side indicates digital zoom.
GETTING READY PLAY mode 12 3 4 1 PLAY mode file type 5 Snapshot Audio Voice Recording 2 Image protection indicator 3 Folder number/File number 8 FINE NORMAL ECONOMY Movie 6 7 5 Quality Snapshot 4 Image size 2304 2304 1600 1280 640 ҂ 1728 ҂ 1536 ҂ 1200 ҂ 960 ҂ 480 pixels (3:2) pixels pixels pixels pixels 24 6 Built-in memory selected for data storage. Memory card selected for data storage.
GETTING READY Changing the Contents of the Monitor Screen Indicator Lamps You can find out the operational status of the camera and the USB cradle at a glance by checking the color of the indicator lamps, and whether a lamp is lit or flashing. For details, see “Indicator Lamp Reference” on page 170. Each press of the [DISP] button changes the contents of the monitor screen as shown below.
GETTING READY Attaching the Strap Power Requirements Attach the strap to the strap ring as shown in the illustration. Your camera is powered by a rechargeable lithium ion battery (NP-20). To load the battery PLAY REC 1. While pressing the battery compartment MENU cover on the bottom of the camera, slide the cover in the direction indicated by the arrow, and then swing it open.
GETTING READY 2. While pulling the stopper in the direction 3. Swing the battery compartment cover closed, indicated by the arrow in the illustration, align the arrow mark on the battery with the arrow mark on the camera and slide the battery into the camera. and then slide it in the direction indicated by the arrow. Stopper IMPORTANT! • Use only the special NP-20 rechargeable lithium ion battery to power this camera. Use of any other type of battery is not supported.
GETTING READY To remove the battery To charge the battery 1. Open the battery compartment cover. 1. Connect the bundled AC adaptor to the [DC IN 5.3V] connector of the USB cradle, and then plug it in to a household power outlet. 2. Pull the stopper in the direction indicated by the arrow. USB Cradle • This will cause the battery to come part way out of the slot. [DC IN 5.3V] AC Adaptor Stopper AC power cord 3. Release the stopper and pull the battery from the camera.
GETTING READY 2. Turn off the camera. NOTE • The bundled AC adaptor is designed for operation with any power supply in the range of 100V to 240V AC. Note, however, that the shape of the AC power cord plug varies according to country or geographic area.
GETTING READY IMPORTANT! • If the [CHARGE] lamp starts flashing red, it means that an error occurs while charging. An error can be caused by any of the following: a problem with the USB cradle, a problem with the camera, or a problem with the battery or how it is loaded. Remove the camera from the USB cradle and see if it works normally. • You can use the USB cradle to charge the camera’s battery, to exchange data with a computer over a USB connection, or when using the Photo Stand feature only.
GETTING READY ■ If the camera works normally ■ Battery Life Guidelines The battery life guideline values given below indicate the amount of time under the conditions defined below the table, until power automatically turns off due to battery failure. They do not guarantee that the battery will provide the amount of service indicated. Low temperatures and continued use reduce battery life. 1. Continue using the camera until the current charge is used up, and then charge the battery.
GETTING READY *2 Normal Recording Conditions • Temperature: 23°C (73°F) • Monitor Screen: On • Zoom operation between full wide to full telephoto every 30 seconds, during which two images are recorded, one image with flash; power turned off and back on every time 10 images are recorded.
GETTING READY • Failure to observe any of the following precautions while using the battery creates the risk of overheating, fire, and explosion. — Never use any other type of charger except the optional charger unit specified for the battery. — Never try to use the battery to power any other device other than this camera. — Never use or leave the battery near open flame. — Never place the battery in a microwave oven, throw it into fire, or otherwise expose it to intense heat.
GETTING READY ● PRECAUTIONS DURING USE • Should you ever notice leakage, strange odor, heat generation, discoloration, deformation, or any other abnormal condition while using, charging, or storing a battery, immediately remove it from the camera or optional charger unit and keep it away from open flame. • If the battery does not achieve full charge after the normal charging time has passed, stop charging. Continued charging creates the risk of overheating, fire, and explosion.
GETTING READY ■ USB Cradle and AC Adaptor Precautions ● BATTERY STORAGE PRECAUTIONS • Make sure you remove the battery when you do not plan to use the camera for a long time. A battery left in the camera discharges very small amounts of power even when power is turned off, which can lead to a dead battery or the need for longer charging before the next use. • Store the battery in a cool, dry place (20°C (68 °F) or lower).
GETTING READY Caution! • Use the AC adaptor where it will not be splashed with water. Water creates the risk of fire and electric shock. • Do not place a vase or any other container filled with liquid on top of the AC adaptor. Water creates the risk of fire and electric shock. Turning the Camera On and Off Press the power button to turn the camera on and off. Pressing the power button to turn on the camera causes the green operation lamp to light temporarily.
GETTING READY ● See page 38 for information about how to use menus. Configuring Power Saving Settings You can configure the settings described below to conserve battery power. Sleep : Automatically turns off the monitor screen if no operation is performed for a specified amount of time in the REC mode. Performing any button operation causes the monitor screen to turn back on. Auto Power Off : Turns off power if you do not perform any operation for a specified amount of time.
GETTING READY 2. Press [MENU]. Using the On-screen Menus Pressing [MENU] displays menus on the monitor screen that you can use to perform various operations. The menu that appears depends on whether you are in the REC mode or the PLAY mode. The following shows an example menu procedure in the REC mode. 1. Turn on the camera, and then align the mode selector with “REC” to enter the REC mode.
GETTING READY ● Menu Screen Operations 3. Press [ ] or [ ] to select the tab you want, When you want to do this: Do this: Move between tabs Press [ ] and [ ]. Move from the tab to the settings Press [ ]. Move from the settings to the tab Press [ ]. Move between the settings Press [ ] and [ ]. Display the options available for a setting Press [ ] or press [SET]. Select an option Press [ ] and [ ]. Register an option selection and exit the menu screen Press [SET].
GETTING READY 6. Perform one of the following operations to Configuring Display Language and Clock Settings apply the setting you configured. To do this: Perform this key operation: Apply the setting and exit the menu screen. Press [SET]. Apply the setting and return to feature selection in step 4. Press [ ]. Apply the setting and return to tab selection in step 3. 1. Press [ ]. 2. Use [ ] to move back up to tab selection.
GETTING READY IMPORTANT! To configure display language and clock settings • The camera’s clock settings are cleared whenever power is totally cut off. This can happen if the battery goes dead while the camera is not being supplied power by the USB cradle. The clock setting screen will appear automatically the next time you turn on power after the settings are cleared. Set the date and time before using the camera.
GETTING READY 3. Use [ ], [ ], [ ], and 6. Use [ ] and [ ] to [ ] to select the geographical area where you live, and then press [SET]. change the date format setting, and then press [SET]. Example: December 24, 2003 4. Use [ ] and [ ] to select the name of the city where you live, and then press [SET]. 5. Use [ ] and [ ] to select the summer time (DST) setting you want, and then press [SET].
GETTING READY 7. Set the current date and the time. To do this: Do this: Change the setting at the current cursor location Press [ ] and [ ]. Move the cursor between settings Press [ ] and [ ]. Toggle between 12-hour and 24hour timekeeping Press [DISP]. 8. Press [SET] to register the settings and exit the setting screen.
BASIC IMAGE RECORDING BASIC IMAGE RECORDING This section describes the basic procedure for recording an image. IMPORTANT! • Make sure your fingers or the strap does not block the flash, microphone or lens. Recording an Image Flash Microphone Aiming the Camera Lens Use both hands to hold the camera still when shooting an image. Holding the camera with one hand increases the chance of movement, which can blur your images.
BASIC IMAGE RECORDING 3. Compose the image Recording an Image on the monitor screen so the main subject is within the focus frame. Your camera automatically adjusts shutter speed in accordance with the brightness of the subject. Images you record are stored in the camera’s built-in memory, or to a memory card if you have one loaded in the camera. • When an optionally available SD memory card or MultiMediaCard (MMC) is loaded in the camera, images are stored on the card (page 134). 1.
BASIC IMAGE RECORDING ● Operation Lamp and Focus Frame Operation 4. Press the shutter release button half way to focus the image. • When you press the shutter release button half way, the camera’s Auto Focus feature automatically focuses the image, and displays the shutter speed and aperture values. • You can tell whether the image is focused by observing the focus frame and the green operation lamp.
BASIC IMAGE RECORDING 5. After making sure that the Recording Precautions image is focused properly, press the shutter release button the rest of the way down to record. • The number of images that can be stored in memory depends on the resolution setting you are using (pages 57,178). • Never open the battery compartment cover or place the camera onto the USB cradle while the green operation lamp is flashing.
BASIC IMAGE RECORDING About Auto Focus About the REC Mode Monitor Screen • Auto Focus tends not to work well if the camera is moved during recording, or when recording the types of subjects listed below.
BASIC IMAGE RECORDING IMPORTANT! Using the Optical Viewfinder • The frame that is visible inside of the viewfinder indicates the image recorded at a distance of about one meter (3.3´). When the subject is closer than one meter, the recorded image will be different from what you see inside the viewfinder frame. • Since the monitor screen shows exactly what will be recorded, always use it for composing your images in the Macro and Manual Focus modes.
BASIC IMAGE RECORDING Using Zoom Your camera is equipped with two types of zoom: optical zoom and digital zoom. Optical Zoom Zoom out Zoom in The range of the optical zoom factor is shown below. Optical Zoom Factor Range: 1X to 3X 2. Compose the image and then press the shutter release button. 1. In the REC mode, press the zoom button to change the zoom factor. NOTES REC • The optical zoom factor also affects the lens aperture.
BASIC IMAGE RECORDING 5. Hold down the Digital Zoom Digital zoom indicator (Telephoto) zoom button to increase the optical zoom factor. Digital zoom is activated after you reach the maximum optical zoom factor (3X). It enlarges the part of the image at the center of the image screen. The range of the digital zoom factor is shown below. • When the digital zoom factor reaches its maximum value (3X), it stops momentarily.
BASIC IMAGE RECORDING IMPORTANT! Using the Flash • Digital zoom is disabled whenever the monitor screen is turned off (page 25). • Using digital zoom can cause degradation of the recorded image. Perform the following steps to select the flash mode you want to use. 1. In the REC mode, press [MENU]. 2. Press [왔] ( ) to select the flash mode. MENU • Each press of [왔] ( ) cycles through the flash mode settings shown below on the monitor screen.
BASIC IMAGE RECORDING To do this: Have the flash fire automatically when required (Auto Flash) ■ About Red-eye Reduction Select this setting: Using the flash to record at night or in a dimly lit room can cause red spots inside the eyes of people who are in the image. This is caused when the light from the flash reflects off of the retina of the eye.
BASIC IMAGE RECORDING Flash Unit Status Flash Precautions You can find out the current flash unit status by pressing the shutter release button half way and checking the monitor screen and red operation lamp. Take care that your fingers do not block the flash when you hold the camera. Covering the flash with your finger can greatly reduce its effectiveness. The indicator is also shown on the monitor screen when the flash unit is ready to fire.
BASIC IMAGE RECORDING • Using flash in combination with another light source (daylight, fluorescent light, etc.) can result in abnormal image colors. Using the Self-timer The self-timer lets you select either a 2-second or 10second delay of the shutter release after you press the shutter release button. A Triple Self-timer feature lets you perform three consecutive self-timer operations to record three images. 1. In the REC mode, press [MENU]. 2. Use [왗] and [왘] to select the “REC” tab. 3.
BASIC IMAGE RECORDING To do this: 5. Record the image. Select this setting: Specify a 10-second self-timer 10 sec Specify a 2-second self-timer 2 sec Specify Triple Self-timer X3 Disable the self-timer Off Self-timer lamp • When you press the shutter release button, the self-timer lamp flashes and the shutter releases after the selftimer reaches the end of its countdown. • With the Triple Self-timer, the camera records a series of three images in the sequence described below.
BASIC IMAGE RECORDING NOTES Specifying Image Size and Quality • If you plan to make large prints of your images or otherwise use them in applications where highresolution is your top priority, select the “2304 x 1728” image size. • If you plan to send images as e-mail attachments or otherwise use them in applications where data economy is your top priority, select the “640 x 480” image size.
BASIC IMAGE RECORDING NOTE To specify image quality • Use the “Fine” setting when image quality is your top priority and file size is secondary. Conversely, use the “Economy” setting when file size is your top priority and image quality is secondary. 1. In the REC mode, press [MENU]. 2. Use [왗] and [왘] to select the “REC” tab. 3. Use [왖] and [왔] to select “Quality”, and then IMPORTANT! press [왘]. • Actual file size depends on the type of image you record.
