(without price) EX-S770D DivX correspondence NOV.
CONTENTS SPECIFICATIONS ....................................................................................................................................... 1 BLOCK DIAGRAM ...................................................................................................................................... 5 TEST MODE ................................................................................................................................................ 6 PROGRAM VERSION UPGRADING ................
SPECIFICATIONS Image Files Format Snapshots: JPEG (Exif Ver.2.2); DCF (Design Rule for Camera File System) 1.0 standard; Recording Media Movies: DPOF compliant MPEG-4 AVI format, DivX Audio: WAV Built-in Memory 6.
Delete Effective Pixels Imaging Element Lens/Focal Distance Zoom Focusing Focus Modes AF Area Approximate Focus Range (from lens surface) Exposure Control Shutter Aperture Value White Balance Sensitivity Self-timer Built-in Flash Flash Modes Approximate Flash Range Recording Approximate Audio Recording Times Monitor Screen Viewfinder Timekeeping Functions World Time Input/Output Terminals USB Microphone Speaker 1 file; all files (with memory protection feature) 7.2 million 1/2.
Power Requirements Power Requirements Lithium ion rechargeable battery (NP-20) x 1 Approximate Battery Life: All of the values provided below represent the approximate amount of time under normal temperature (23°C ( 73° F)) before the camera turns off. These values are not guaranteed. Low temperatures shorten battery life.
Rechargeable Lithium Ion Battery (NP-20) Rated Voltage 3.7 V Rated Capacitance 700 mAh Operating Temperature Dimensions 0 to 40°C (32 to 10 4°F) 33.0 (W) ✕ 50.0 (H) ✕ 4.7( D) mm (1.3˝(W) ✕ 2.0˝(H) ✕ 0.19˝(D)) Weight Approximately 16 g (0.56 oz) USB Cradle (CA-34) Input/Output Terminals Camera contact; USB port; external power supply terminal (DC IN 5.3 V); Power Consumption AV terminal (AV OUT: NTSC/PAL standards) 5.3V DC Approximately 3.2W Dimensions 109(W) ✕ 24(H) ✕ 58(D) mm (4.3˝(W) ✕ 0.
CCD Flexible-board Moter Flexible-Board —5— Connector 27PIN VEE7.5 MOTER-dr LV8054LP CDS+Vdr R2J45002HBG Vcc3.3-1 MOTOR-BUS CCD-BUS VEE7.5C VCC13C VEE7.5C VCC13C VCC13C VEE7.5C VCC13 Connector 25PIN Vcc5-2 Vcc3.3D SD Card Connector SDBUS Vcc3.3D 48MHz LSI-SIP R8J30215EBGV (SATURN) Vcc1.2 Vcc1.8 Vcc3.3D Vcc3.3A LCDBUS Connector 44PIN AV-BUS AV-BUS Vcc3.3D BS MENU DISP WIDE Vcc3.
TEST MODE Note: Never perform the menu items unless otherwise instructed. Doing so may cause destruction of the data inside, which will make the camera unusable. ■ To boot the test mode 1. While firmly pressing down both [BS], [PW ON] and [UPPER], turn the power on. [UPPER] button [BS] button 2. After the version appears, press buttons in the order of [DOWN], [DOWN], [BS] and [MENU] in 0.5 second. The diagnostic menu appears. [DOWN] button [MENU] button ++ KX837f ++ Ve r 1 .
PROGRAM VERSION UPGRADING 1. To update the firmware version 1. Prepare the memory card which contains the firmware for EX-S770D in the root directory. EX-S770D.BIN 2. Insert the above memory card into the camera, and set a fully charged battery in the camera. 3. Press the [power button] while holding [MENU] depressed. Keep holding [MENU] depressed until “PROGRAM UPDATE” appears in the display. • The following appears. • The version of the firmware in the memory card appears at the bottom of the display.
2. How to restore the firmware 1. Prepare the firmware restoration program and change its name as follows; rom837f-gm11.lbn 씮 saturn.bin NOTE: This software and procedure automatically restores the firmware even if the firmware belongs to a wrong model code. Make sure to use the correct software for the correct model. 2. Copy the above file to the root directory in the memory card. 3. Insert the memory card into the camera. 4. Set a fully charged battery in the camera.
3. To install the firmware Initially, firmware is not installed in the PCB supplied by the parts center. Install the firmware into the PCB after replacing with a new one as shown in the procedures below. Note: The camera does not operate (only LED becomes “green blinking”) if the firmware is not installed in the PCB. 1. Copy the following software to the root directly of the SD card. Restoration software: rom837f-gm11.lbn Firmware: EX-S770D.BIN 2.
ADJ TOOL ■ Introduction Make sure to perform the adjustment by the USB ADJ Tool “adj03SSAW.exe” when replacing the lens unit or the PCB. Here the necessary software, driver and setting are explained to use “adj03SSAW.exe”. Note that the tool, drivers etc. are available only for Windows. 1. Preparation 1-1. Prepare the necessary software, driver and DLL file. 1) Prepare the following three files. • Testmode driver [testmode_driver] folder uusbd.dll uusbd.inf uusbd.sys * testmode_driver_2.
7) Check “Designate the place to search”, designate the place which contains “inf” file in the driver by pressing “Reference” button, and then press “Next” button. 8) When “Universal USB Driver (VMEM manufacturer’s name)” appears upon message “Searching for the driver file for the following devices”, press “Next” button. 9) The file copy starts. (If a message “uusbd.inf cannot be found” appears during the file copy, designate the same place as in the step 7). 10) Press “Complete” button.
2. How to use ADJ Tool when replacing Lens unit Make sure to perform the following procedure after replacing the lens. A floppy disk with the lens data is bundled in the spare parts of the lens unit. 1 Enter the TEST mode. 1. Turn the power on while pressing both "BS" and "UP" buttons. 2. Press "DOWN" button, "DOWN" button, "BS" button, and "MENU" button while the program version is displayed. 3. Select "2.USB TCC TEST", and press "SET" button. 4. Select "1.
3. How to use ADJ Tool when replacing MAIN PCB Firmware is not installed in spare parts. 1 Enter the TEST mode. 1. Turn the power on while pressing both "BS" and "UP" buttons. 2. Press "DOWN" button, "DOWN" button, "BS" button and "MENU" button while the program version is displayed. 3. Select "2.USB TCC TEST", and press "SET" button. 4. Select "1. USB TCC ON", and press "RIGHT" button, "RIGHT" button and "SET" button. 5. Turn the power OFF. 2 Connect the camera to the PC by the USB cable.
VCOM DC ADJUSTMENT ■ Purpose Readjust the VCOM value to minimize the flicker of the LCD after replacing the LCD or the main PCB. ■ Necessary tools 1. Camera (Charge its battery fully) 2. Photo diode (S2281-01) : See Fig 1. 3. Photo sensor amp (C2719) : See Fig 2. 4. BNC-BNC cable (E2573) x 2 : See Fig 3. 5. 9-volt alkaline battery (6LR61Y) x 2 : See Fig 4. 6. Oscilloscope ■ Preparation 1. The three tools can be obtained from the following global site.
■ Procedure 1. Camera setting a) Turn the power on while pressing “BS” and “UPPER”. After pressing “DOWN” key twice, press “BS” and “MENU”. Select "2:USB TCC TEST", and press "SET" button. Select "1:USB TCC ON", and press "RIGHT" button ,"RIGHT" button and "SET" button. Figure (a) appears. Figure (a) 1: VERSION INFO 2: USB TCC TEST 3: ROM UPDATE 4: LAST MEMORY 5: FORMAT 6: HARD TEST 7: IMAGE TEST 8: ADJ TEST 9: TEST SCRIPT b) Select “8 : ADJ_TEST” and then press SET. (See Figure (b).
3. Measurement a) Connect S2281-01 to the camera’s LCD monitor (see below). AC Waveforms appear on the monitor screen of the oscilloscope. * Change the Rf range of C2719 in case the range does not match. Photo diode S2281-01 INPUT OUTPUT Oscilloscope Photo sensor amp CAMERA BNC-BNC cable LCD Minimize the ripple components b) After AC waveforms of the oscilloscope appear, minimize it by pressing the camera’s up/down buttons (see the picture). Make sure to visually check if it has been minimized.
CURRENT CONSUMPTION (1) Current consumption (DC in = 3.80 ± 0.1 [V]) • Make sure that current consumption is less than 215 mA in PLAY mode. (TCC ON, USB connection : less than 250 mA) • Make sure that current consumption is less than 440 mA in REC mode. (TCC ON, USB connection : less than 475 mA) • Make sure that current consumption is less than 500 µA when power is turned OFF. (TCC ON, USB connection : less than 630 µA) (2) The battery indicator changes according to the voltages as follows.
RESETTING THE PLACE OF DESTINATION When the main PCB is replaced, the setting of the destination will be changed, therefore resetting is required. However, when the firmware is changed or fixed, the setting of the destination will be held, therefore resetting is not required. Use the destination setting script to change the destination flag as instructed below. 1. Have an SD card ready that have a corresponding script (autorun.scp) under the root directory. 2.
DISASSEMBLY * Make sure to use correct screws when assembling since there are several kinds of them. It is a good idea to sort them as shown in the right when disassembling. 1. Remove the battery. 2. Remove two screws and then remove C-CASE-BA. Screws (S1) C-CASE-BA 3. Remove two screws and then remove C-CASE-CA. C-CASE-CA Screws (S1) 4. Remove one screw and then remove C-CASE-ASSY.
5. Remove six screws. Screw (S3) Screws (S4) Screw (S4) Screws (S2) 6. Remove the rear panel. Attention: The power button and the shutter button come off together. Be sure not to lose them. Rear panel Power button 7. Remove the front panel.
* Cam ring is fixed with three special screws ( ). 8. Remove the strap board. Strap board 9. Remove the REC SUB ASSY and the DATA SUB ASSY. * Fixed with double-sided tape.
10. Release the lock and remove two FPCs. FPCs 11. Remove two hooks and then remove the lens unit. * Hooks are located at three locations as below.
12. Remove the tape fixing the FPC(LCD). 13. Release the lock and remove one FPC. 14. Remove the tape. 15. Unsolder to remove two lead wires.
16. Remove the LCD unit. * Fixed at three locations with double-sided tape. 17. Remove one screw and then remove the battery case. Screw (S4) Battery case 18. Remove the tape. 19. Unsolder to remove two lead wires.
20. Remove the tape. 21. Release the lock and remove two FPCs. 22. Remove one screw. Screw (S5) 23. Unsolder to remove three lead wires. 24. Remove the main PCB. Lead wire (yellow) main PCB Lead wire (blue) Lead wire (gray) 25. Remove the protection tape and then discharge the strobe condenser.
26. Remove the key FPC. * Fixed with double-sided tape. Key FPC 27. Remove the shutter plate. Shutter plate 28. Remove the TRIPOD ASSY.
. Remove the strobe assy. * Fixed with four hooks. Strobe assy 30. Remove the strobe assy. * Fixed with three hooks.
ASSEMBLY 1. Set the strobe case assy. * Fix it with three hooks. Strobe case assy 2. Set the strobe assy. * Fix it with three hooks. Strobe assy 3. Remove the TRIPOD assy. * Fix it with three hooks. 4. Set the shutter plate.
5. Set the LCD. * Fix it with a double-sided tape at three locations. Double-sided tape * If the key FPC is not removed, place the LCD FPC under the key FPC. 6. Set the key FPC. There are eight pins as your positioning guide. Follow the assembling order as below.
7. Solder two LCD lead wires. 8. Tape on the lead wires. Lead wire (white) Lead wire (black) 9. Set the battery case with one screw. Buttery case 10. Set the LCD with one screw.
11. Solder two speaker lead wires. 12. Tape on the lead wires. Lead wire (black) Lead wire (red) 13. Solder three power lead wires. Lead wire (yellow) Lead wire (blue) 14. Connect three FPCs. 15. Tape on FPC at two locations.
16. Set the lens unit. * Fix it with three hooks. Hooks Lens unit 17. Connect two FPCs of the lens unit. 18. Set the REC sub assy and the DATA sub assy. REC sub assy DATAsub assy 19. Stick the conductive (black) ring onto the front panel. There is no conductive ring on the front panel assembly in maintenance parts. Use double-sided tape to attach the conductive ring.
■ Procedure for attaching the conductive ring Preparation: • Defective lens with the lens fully extended (A defective lens from an EX-Z500 or Z600 can also be used.) • Double-sided tape (4 pieces) (1) Attach the 4 pieces of double-sided tape and remove the protective stickers. Double-sided tape Double-sided tape (2) Fit the defective lens into the front panel assembly as shown in the figure.
(4) Take the front panel assembly off the defective lens. (5) Press on the conductive ring to fix it in place. 20. Set the front panel. 21. Set the strap board.
22. Set the power button the shutter button. 23. Set the rear panel. 24. Assemble with six screws.
25. Set the C-CASE-ASSY with one screw. Screw (S3) C-CASE-ASSY 26. Set the C-CASE-BA with two screws. Screws (S1) C-CASE-BA 27. Set the C-CASE-CA with two screws.
EXPLODED VIEW 37 S3 S1 38 39 40 1 5 21 9 2 4 3 S4 41 6 S2 7 21 9 42 8 10 14 12 16 15 11 17 20 13 16 43 33 19 44 36 18 S5 28 29 S3 22 S6 23 44 S4 27 24 21 26 S1 S4 S1 34 32 35 45 S2 S1 — 37 — 31 30 25
PARTS LIST 1 EX-S770D_SILVER-EU N Item Parts Code N 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 10252942 10251069 10236155 10251070 10251116 10254837 10254839 10251080 10251137 10251111 10251115 10251107 10252936 10252933 10200800 10241457 10251106 10170543 10113024 10252927 10254783 10251135 10251484 10200801 10252934 10251119 10251121 10200827 10251141 10251120 10251122 10251071 10252937 10251093 10251078 10251079 10252
1 EX-S770D_SILVER-EU N N QTY 1 4 2 2 4 1 3 Price Code AA AA AA AA AA AA FCC10801ABPA FHC10252ABPA 1 1 AA AA B B CK837FCA01R AV-K800-BK15 UC-K815-BK10-MB CBL-K835-AC-EU-06 AD6008CJ WAU0990-012AE MK11-2855 ST-K872-S 1 1 1 1 1 1 1 1 AJ AI AF AZ CB BS AB C C C C EU type C C B X Item Parts Code S1 S2 S3 S4 S5 S6 10203893 10226146 10254784 10081372 10153233 10170415 SCREW SCREW SCREW SCREW SCREW SCREW RJK502836-011V01 RJK508552-001V01 RJK502836-015V02 RJK502836-001V01 RJK506113-001V01 RJK506541-0
PRINTED CIRCUIT BOARD MAIN PCB (TOP VIEW) FU100 — 40 — FU101
MAIN PCB (BOTTOM VIEW) — 41 —
CASIO COMPUTER CO.,LTD.
