(without price) EX-S2/M2 SEP. 2002 EX-S2 INDEX EX-M2 R Ver. 3 Ver. 2 MAR. / 2003 NOV. / 2002 Ver. 1 OCT.
CONTENTS SPECIFICATIONS ....................................................................................................................................... 1 BLOCK DIAGRAM ...................................................................................................................................... 4 TEST MODE ................................................................................................................................................ 5 PROGRAM VERSION UPGRADING ................
SPECIFICATIONS Image Files Format Snapshots: JPEG (Exif Version 2.2); DCF (Design Rule for Camera File System)1.
Exposure Control Shutter Metering: Multi-pattern by imaging element Exposure: Program AE Exposure Compensation: –2EV to +2EV (in 1/3EV steps) CCD shutter, mechanical shutter 1/4 to 1/6400 second Aperture F3.
Dimensions EX-S2: 88(W) x 55(H) x 11.3(D) mm (3.5˝(W) x 2.2˝(H) x 0.4˝(D)) (excluding projections) EX-M2: 88(W) x 55(H) x 12.4(D) mm (3.5˝(W) x 2.2˝(H) x 0.5˝(D)) (excluding projections) Weight EX-S2: Approximately 88 g (3.1 oz) (excluding battery and accessories) EX-M2: Approximately 90 g (3.
BLOCK DIAGRAM CCD-Lenz module Mechanical shutter Main-PCB CDS HD4933 V-Driver CXD3440 Strobe Unit 8bit micom M37516 16M Flash Memory SH-micom 1.
TEST MODE Note: Do not perform the menu item unless explained here. (It may damage the internal data and camera becomes unusable.) Booting To boot the test mode While firmly pressing down both "MENU" and "SET" buttons, Turn the power on. Continue pressing "MENU" and "SET" until the MAIN MENU is displayed. 2 "POWER" button 1 "MENU" + "SET" buttons While holding the camera in a horizontal position, press the set button twice towards your "RIGHT" and then press "MENU" .
PROGRAM VERSION UPGRADING ■ Introduction Update the program using an SD card. Note: Make sure to use a fully charged battery. MAIN PCB becomes unusable if power down or an error occurs during program transmission. 1. How to confirm the program version ■ The program version can be confirmed in the test menu (refer to the previous page). ■ Turn the power on while pressing MENU button. The following program version also can be found. Check the LCD display. (Example) VER 1.00 (As of August 06. 2002) 2.
6. Remove the memory card after turning the power off once. Turn the power back on again while pressing MENU, and check the version. VER 1.00 • “VER 1.00” appears this time. 7. If the version is correct, turn the power off. 8. Finally, check the operation by recording, playing back and deleting an image. 3. How to restore the firmware 1. Prepare the following firmware restoration program and change its name as follows; EX-S2 kx853r0802.hbn 앶앸 mercury.bin EX-M2 kx854r0802.hbn 앶앸 mercury.bin 2.
COLOR ADJUSTMENT ■ Introduction Make sure to perform the adjustment when replacing the lens unit or the MAIN PCB. The necessary software, driver and setting are explained in using USB ADJ Tool "adj331e.exe (Ver.1.1). Note that the tool, drivers etc. are available only for Windows. 1. How to use USB ADJ Tool 1-1. Prepare the necessary software, driver and DLL file. (1) Prepare the following three files. • Commom test driver for CASIO/PENTAX [testmode_pentax_casio] folder uusbd.dll uusbd.inf uusbd.
NOTE: How to uninstall the USB driver for the USB test mode • Connect the camera while in the USB test mode to the computer so that the computer recognises the camera. • Right-click "My computer", select "Property" and open "Device manager". • Select "USB device for UUSBD" , and then "Universal USB Driver (VMEM manufacturer's name)". • Press "Delete" button and delete the driver. • When using Windows98/98SE/Me, delete the following three files; (NOTE! Do NOT delete "usbd. inf" and "usbd.
2. Lens Replacement Make sure to perform the following procedure after replacing the lens. A foppy disk with the lens data is bundled in the spare parts of the lens unit. 1 Enter the TEST mode. 1.Turn the power on while pressing both "MENU" and "SET" buttons. 2.Press "RIGHT" button, "RIGHT" button and "MENU" button while the program version is displayed. 3.Select "3.USB TCC TEST". 4.Select "1. USB TCC ON". 5.Turn the power OFF.
4 5 6 7 Click "ADJ ALL READ", and display the data on the "adj331e.exe". Save the data. Replace the MAIN PCB. Perform the above 1 to 3. 5 4 8 Open the file which is saved above, and display the data on the "adj331e.exe". 9 Click "WRITE" button of "ADJ ALL". 0 After adjustment, change "1. USB TCC ON" to "2. USB TCC OFF". 8 9 4. Operation and Current consumption 1.
DISASSEMBLY NOTE : Here EX-M2 is used. 1. Remove the CARD, BATTERY and the JACK COVER. 2. Remove five screws. Screws Screws Screw 3. Remove the REAR CASE ASSY.
4. Removing the LCD ASSY 1 Remove the hook from the MAIN PCB and slide the LCD ASSY. 2 Remove the CONNECTOR. 3 Remove the LCD ASSY. 1 2 3 Connector NOTE: Fix the FPC to the CONNECTOR tightly when assembling. 5. Remove the FPC from the CONNECTOR and then remove the SW UNIT.
6. Removing the SUB PCB ASSY 1 Unsolder the five lead wires. 2 Remove the hook and then the SUB PCB ASSY. The SUB PCB is connected to the MAIN PCB by the CONNECTOR. Note in assembling *1 Position these four lead wires in the space between the MAIN PCB and the SUB PCB. *2 Make sure that this lead wire does not touch the battery spring. × 2 *1 × 2 *1 1 × 1 *2 2 7. Removing the STROBE UNIT (NOTE: The STROBE UNIT does not need be discharged.) 1 Remove the STROBE PLATE.
8. Removing the LENS UNIT 1 Remove the CONNECTOR. 2 Remove the LENS UNIT while taking care of the hook. Hook 9. Remove the MAIN PCB. 10. Remove the microphone (EX-M2 only).
22 14 13 7 S1 19 4 2 10 20 11 S1 21 — 16 — 1 12 18 8 S1 15 5 6 17 16 Dumy Card/ SD Card EXPLODED VIEW 3 9
PARTS PRICE LIST EX-S2 / EX-M2 N Item N N N 1 2 2 2 2 3 3 3 3 4 4 5 6 6 7 8 9 10 11 12 13 14 15 16 16 17 18 18 19 19 20 20 21 21 S1 N N N N N N N N N N N N N N N - Parts Code Parts Name 1009 2320 LENS UNIT 1009 2324 ASSY / FRONT CASE K853 1009 2331 ASSY / FRONT CASE K854 1009 2322 ASSY / FRONT CASE K853 1009 2330 ASSY / FRONT CASE K854 1009 2327 ASSY / REAR CASE K853 1009 2333 ASSY / REAR CASE K854 1009 2325 ASSY / REAR CASE K853 1009 2332 ASSY / REAR CASE K854 1009 2329 ASSY / BATTERY COVER 1008 52
PRINTED CIRCUIT BOARDS MAIN PCB TOP VIEW — 18 —
MAIN PCB BOTTOM VIEW — 19 —
SUB PCB TOP VIEW BOTTOM VIEW — 20 —
SCHEMATIC DIAGRAMS MAIN PCB — 21 —
SUB PCB (EX-S2 only) — 22 —
SUB PCB (EX-M2 only) — 23 —
Ver. 1 : Correction of page 5, 6, 7, 8, 9, 10, 11 and 17. Ver. 2 : Correction of page 15. Ver. 3 : Correction of page 17. CASIO TECHNO CO.,LTD. Overseas Service Division Nishi-Shinjuku Kimuraya Bldg.
