(without price) EX-Z1000 MAY. 2006 ■ Refer to the page 18 after changing the main PCB.
CONTENTS SPECIFICATIONS ....................................................................................................................................... 1 BLOCK DIAGRAM ...................................................................................................................................... 5 TEST MODE ................................................................................................................................................ 6 PROGRAM VERSION UPGRADING ................
SPECIFICATIONS Image Files Format Recording Media Snapshots: JPEG (Exif Ver.2.2); DCF (Design Rule for Camera File system) 1.0 standard; Movies: DPOF compliant Motion JPEG AVI format Audio: WAV Built-in Memory 8.
Delete Effective Pixels Imaging Element Lens/Focal Distance Zoom Focusing Approximate Focus Range (from lens surface) Exposure Control Shutter Aperture Value White Balance Sensitivity Self-timer Built-in Flash Recording Approximate Audio Recording Times Monitor Screen Viewfinder Timekeeping Functions World Time Input/Output Terminals USB Microphone Speaker 1 file; all files (with memory protection feature) 10.1 million 1/1.8 square pixel primary color CCD (Total pixels: 10.37 million) F2.8 to 5.
Power Supply Power Requirements Lithium ion rechargeable battery (NP-40) x 1 Approximate Battery Life All of the values provided below represent the approximate amount of time under normal temperature (23°C (73°F)) before the camera turns off. These values are not guaranteed. Low temperatures shorten battery life.
Rechargeable Lithium Ion Battery (NP-40) Rated Voltage 3.7 V Rated Capacitance 1300 mAh Operating Temperature Dimensions 0 to 40°C (32 to 104°F) 38.5 (W) x 38.0 (H) x 9.3 (D) mm (1.53"(W) x 1.50"(H) x 0.37"(D)) Weight Approximately 34 g (1.2 oz) USB Cradle (CA-33) Input/Output Terminals Camera contact; USB port; external power supply terminal (DC IN 5.3 V); Power Consumption AV terminal (AV OUT: NTSC/PAL standards) 5.3 V DC, Approximately 3.2 W Dimensions 107 (W) x 17 (H) x 58 (D) mm (4.
CCD MN39850PAJ3L 1/1.8" 10M Lens Unit PENTAX 3X 23PIN —5— Connector CCD-FPC 33PIN VCC12C VEE6C Vcc5-2 VEE6 Vcc3.3D CDS+Vdr AD9927BBCZRL VCC12C VEE6C VEE6C MOTOR-BUS MOTOR-dr LV8054LP VCC12C Vcc3.3-1 VCC13 Motor FPC Connector Vcc3.3D LCDBUS Connector 45PIN SD Card Connector SDBUS Vcc3.3D 48MHz LSI-SiP R8J30225EBGV Vcc3.3D D+/D- LEFT PLAY Vcc1.2 Vcc1.8 Vcc3.3-1 Vcc3.3A Vcc3.3D EVcc3.3 Vcc5-1 Vcc5-2 VCC13 VEE6 BLLEDA Vcc1-0 Vcc1-1 8bit-BUS VIDEO IC NJW1351RB1 Vcc3.
TEST MODE Note: Never perform the menu items unless otherwise instructed. Doing so may cause destruction of the data inside, which will make the camera unusable. ■ To boot the test mode 1. While firmly pressing down both [BS] and [UPPER], turn the power on. [UPPER] button [BS] button 2. After the version appears, press buttons in the order of [DOWN], [DOWN], [DISP] and [MENU] in 0.5 second. The diagnostic menu appears. [MENU] button [DISP] button ++ KX800 ++ Ve r 1 .
PROGRAM VERSION UPGRADING 1. To update the firmware version 1. Prepare the memory card which contains the firmware for EX-Z1000 in the root directory. EX-Z1000.bin 2. Insert the above memory card into the camera, and set a fully charged battery in the camera. 3. Press the [power button] while holding [MENU] depressed. Keep holding [MENU] depressed until “PROGRAM UPDATE” appears in the display. • The following appears. • The version of the firmware in the memory card appears at the bottom of the display.
2. How to restore the firmware 1. Prepare the firmware restoration program and change its name as follows; rom800_060512.lbn 씮 titan.bin NOTE: This software and procedure automatically restores the firmware even if the firmware belongs to a wrong model code. Make sure to use the correct software for the correct model. 2. Copy the above file to the root directory in the memory card. 3. Insert the memory card into the camera. 4. Set a fully charged battery in the camera.
3. To install the firmware Initially, firmware is not installed in the PCB supplied by the parts center. Install the firmware into the PCB after replacing with a new one as shown in the procedures below. Note: The camera does not operate (only LED becomes “green blinking”) if the firmware is not installed in the PCB. 1. Copy the following software to the root directly of the SD card. Restoration software: rom800_060512.lbn Firmware: EX-Z1000.bin 2.
ADJ TOOL ■ Introduction Make sure to perform the adjustment by the USB ADJ Tool “adj03SSAW.exe” when replacing the lens unit or the PCB. Here the necessary software, driver and setting are explained to use “adj03SSAW.exe”. Note that the tool, drivers etc. are available only for Windows. 1. Preparation 1-1. Prepare the necessary software, driver and DLL file. 1) Prepare the following three files. • Testmode driver [testmode_driver] folder uusbd.dll uusbd.inf uusbd.sys * testmode_driver_2.
7) Check “Designate the place to search”, designate the place which contains “inf” file in the driver by pressing “Reference” button, and then press “Next” button. 8) When “Universal USB Driver (VMEM manufacturer’s name)” appears upon message “Searching for the driver file for the following devices”, press “Next” button. 9) The file copy starts. (If a message “uusbd.inf cannot be found” appears during the file copy, designate the same place as in the step 7). 10) Press “Complete” button.
2. How to use ADJ Tool when replacing Lens unit Make sure to perform the following procedure after replacing the lens. A floppy disk with the lens data is bundled in the spare parts of the lens unit. 1 Enter the TEST mode. 1. Turn the power on while pressing both "BS" and "UP" buttons. 2. Press "DOWN" button, "DOWN" button, "DISP" button, and "MENU" button while the program version is displayed. 3. Select "2.USB TCC TEST", and press "SET" button. 4. Select "1.
3. How to use ADJ Tool when replacing MAIN PCB Firmware is not installed in spare parts. 1 Enter the TEST mode. 1. Turn the power on while pressing both "BS" and "UP" buttons. 2. Press "DOWN" button, "DOWN" button, "DISP" button and "MENU" button while the program version is displayed. 3. Select "2.USB TCC TEST", and press "SET" button. 4. Select "1. USB TCC ON", and press "RIGHT" button, "RIGHT" button and "SET" button. 5. Turn the power OFF. 2 Connect the camera to the PC by the USB cable.
VCOM DC ADJUSTMENT ■ Purpose Readjust the VCOM value to minimize the flicker of the LCD after replacing the LCD or the main PCB. ■ Necessary tools 1. Camera (Charge its battery fully) 2. Photo diode (S2281-01) : See Fig 1. 3. Photo sensor amp (C2719) : See Fig 2. 4. BNC-BNC cable (E2573) x 2 : See Fig 3. 5. 9-volt alkaline battery (6LR61Y) x 2 : See Fig 4. 6. Oscilloscope ■ Preparation 1. The three tools can be obtained from the following global site.
■ Procedure 1. Camera setting a) Turn the power on while pressing “BS” and “UPPER”. After pressing “DOWN” key twice, press “DISP” and “MENU”. Select "2:USB TCC TEST", and press "SET" button. Select "1:USB TCC ON", and press "RIGHT" button ,"RIGHT" button and "SET" button. Figure (a) appears. Figure (a) 1: VERSION INFO 2: USB TCC TEST 3: ROM UPDATE 4: LAST MEMORY 5: FORMAT 6: HARD TEST 7: IMAGE TEST 8: ADJ TEST 9: TEST SCRIPT b) Select “8 : ADJ_TEST” and then press SET. (See Figure (b).
3. Measurement a) Connect S2281-01 to the camera’s LCD monitor (see below). AC Waveforms appear on the monitor screen of the oscilloscope. * Change the Rf range of C2719 in case the range does not match. Photo diode S2281-01 INPUT OUTPUT Oscilloscope Photo sensor amp CAMERA BNC-BNC cable LCD Minimize the ripple components b) After AC waveforms of the oscilloscope appear, minimize it by pressing the camera’s up/down buttons (see the picture). Make sure to visually check if it has been minimized.
CURRENT CONSUMPTION (1) Current consumption (DC in = 3.80 ± 0.1 [V]) • Make sure that current consumption is less than 230 mA in PLAY mode. • Make sure that current consumption is less than 440 mA in REC mode. • Make sure that current consumption is less than 300 µA when power is turned OFF. (2) The battery indicator changes according to the voltages as follows. • DC in = less than 3.70 ± 0.02 V: (PLAY mode) • DC in = less than 3.60 ± 0.02 V: (PLAY mode) (PLAY mode) • DC in = less than 3.50 ± 0.
RESETTING THE PLACE OF DESTINATION When the main PCB is replaced, the setting of the destination will be changed, therefore resetting is required. However, when the firmware is changed or fixed, the setting of the destination will be held, therefore resetting is not required. Use the destination setting script to change the destination flag as instructed below. 1. Have an SD card ready that have a corresponding script (autorun.scp) under the root directory. 2.
DISASSEMBLY * Make sure to use correct screws when assembling since there are several kinds of them. It is a good idea to sort them as shown in the right when disassembling. 1. Remove the battery. ■ Remove the case 2. Remove six screws.
3. Remove the rear case assy. 4. Remove the center case (A) and the power button. Note: Make sure not to lose the power button. Power button Center case (A) 5. Remove the keypad. Keypad 6. Remove the strap and the center case (B).
7. Remove two screws and then remove the front panel assy. Screw (S1) Screw (S2) Note: Discharge the strobe condenser. ■ Removing the LCD 8. Remove two screws and then remove the clamp board. Clamp board Screw (S1) Screw (S3) 9. Unsolder to remove two lead wires. 10. Release the connector lock and remove the FCP.
11. Remove the LCD. * Fixed with double-sided tape. Double-sided tape Remove the LCD FPC that can be found under key FPC. ■ Removing the key FPC 12. Release the connector lock and remove the FCP. 13. Remove the key FPC.
■ Removing the strobe assy 14. Release the connector lock and remove the FCP. 15. Unsolder to remove two lead wires. Lead wire (red) Lead wire (black) Lead wire (gray) 16. Remove two hooks, and then remove the strobe assy. Strobe assy 17. Remove three hooks, and then remove the shutter unit.
■ Removing the mail PCB and the bottom sub assy 18. Release the connector lock and remove two FCP. 19. Remove four screws. Screw (S4) Screw (S3) Screw (S1) Screw (S3) 20. Remove the hook, and then remove the mail PCB and the bottom sub assy. 21. Unsolder to remove two lead wires.
22. Remove the bottom sub assy. Bottom sub assy Connecter plate Main PCB. 23. Remove the speaker. * Fixed with double-sided tape. ■ Removing the lens unit. 24. Remove two hooks, and then remove the lens unit.
ASSEMBLY ■ Assembling the lens unit 1. Set the lens unit and fix it with three hooks. ■ Assembling the speaker 2. Set the lens unit and fix it with three hooks. * Pay attention to the lead wire positions.
■ Assembling the main PCB and the bottom sub assy 3. Set the connector plate. Connector plate 4. Set the main PCB.
■ Assembling the buttery box assy 5. Set the connector plate. * Place two FPCs above. NG NG 6. Fix it with four screws.
7. Insert two FPCs. 8. Solder five lead wires. Lead wire (black) Lead wire (red) Lead wire (gray) Lead wire (red) Lead wire (black) * Make sure to place to the right directions when soldering lead wires. ■ Assembling the strobe assy 9. Set the strobe assy and fix it with the hook. * Positioning guides.
■ Assembling the key FPC 10. Set the key FPC. * Positioning guides 11. Insert one FPC. * FPC should be placed under the lead wires.
■ Assembling the LCD 12. Lead the FPC through the buttery box clearance. 13. Fix the LCD with a double-sided tape and insert one FPC. 14. Solder tow lead wires. * Wire the lead wires along the edge of the LCD.
■ Assembling the clump board 15. Set the clump board. * Do not nip the lead wires. 16. Fix with two screws. Screw (S1) Screw (S3) ■ Assembling the case 17. Set the front case and fix it with two screws. Screw (S1) Screw (S2) 18. Set the keypad.
19.Set the center case (B). 20.Set the strap. 21. Set the rear case. * Do not nip the lead wires. 22. Fix it with five screws. Screw (S3) Screw (S2) Screw (S3) Screw (S3) Screw (S2) 23. Set the power button. 24. Set the center case (A). 25. Fix it with one screw.
— 34 — 23 22 24 23 S3 S2 S1 13 6 32 S1 14 12 10 18 5 S3 8 S1 16 7 11 4 20 19 21 9 7 17 31 S1 15 3 30 26 29 S3 S2 28 27 S5 2 S3 S4 S3 2 1 S2 25 EXPLODED VIEW
PARTS LIST N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 S1 S2 S3 S4 S5 Parts Code 10242103 10241458 10219347 10241438 10241439 10241441 10241440 10241467 10242108 10241452 10241447 10241456 10241455 10241960 10241962 10241454 10241451 10241491 10234007 10241464 10241463 10241958 10241472 10241471 10241959 10242106 10241475 10241448 10241465 10241466 10241453 10243984 10203893 10241435 1024143
N Item N N - N N Parts Code Parts Name ACCESSORIES 10243983 CD ROM 10242037 AV CABLE 10235765 USB CABLE 10210351 AC CORD 10210354 AC CORD 10210360 AC CORD 10210350 AC ADAPTOR 10211299 AC ADAPTOR 10242036 CRADLE 10242035 BATTERY/LI-ION 10187367 STRAP N *1 *2 *3 Specification CK800DCA01R AV-K800-BK15 UC-K815-BK10-MB CBL-K835-AC-EU-06 CBL-K835-AC-UK-06 CBL-K835-AC-TW-06 AD-C52G-WW AD-C52J-WW R68-8209 MK11-2875 ST-K872-S New parts Floppy disk is bundled. AC cord is not equipped.
PRINTED CIRCUIT BOARD MAIN PCB (TOP VIEW) FU101 FU100 — 37 —
MAIN PCB (BOTTOM VIEW) — 38 —
SCHEMATIC DIAGRAMS VCC1.8 VCC3.3D 1005 CCD-BUS CCD-BUS L401 AG700 L400 AG700 1005 VCC1.2 VCC3.3A MAIN PCB (1/3) VCC1.8 USB/SD-BUS VCC1.2 PW/KEY-BUS TH KIN4 D0 13 295 296 297 298 VSS_47 12 299 300 301 302 D4 PSRDY 0603 0603 R219 1k R217 1005 C218 6.3V 35 37 31 34 36 J K L M IRIS1 124 IRIS0 0603 100k ADPIN 0603 BATTEMP PWCTL2 P06 P74/KR4 WATCH P33/TI51/TO50/INTP4 P75/KR5 R229 26 SHUTSW P31/INTP2 1k 25 0603 1005 3 VBUS 1 B0.
MAIN PCB (2/3) CDSCK GPO3 C309 GPO7 12 100 NC1 91 95 98 83 87 79 70 72 75 SL 92 88 84 80 76 73 71 67 66 93 89 85 81 77 74 65 64 63 AVSS 9 104 105 106 94 90 86 82 78 62 61 60 59 OPOUT LM D1 109 8 107 108 109 110 V14 58 57 56 55 54 53 52 51 MPI CDTI 40 D10 9 13 17 21 25 29 33 39 38 2 128 5 8 12 16 20 24 28 32 35 37 SUBCK 1 CSN 10uF 6.
MAIN PCB (3/3) DC FU101 3 VCC1-0 to STROBE PWCTL2 PWCTL3 PW/KEY-BUS FU101 1.5A VCC1-1 D100 FCC10152ABPA 1005 C106 B0.022u Q104 4 2 5 1 6 PWCTL5 1.5 1.5 2 Vout={(R113+R114)/R115}+1[V] 2.0 P102 MOTOR AF_LED ) TH GND P110 VCC3.3-1 0.8 1005 2 1005 DTC144EM R112 0 LX VSS 4 3 C111 B22u 1.8( P101 VIN CE/MODE VOUT XC9225A33CMR AFE SPEAKER 6.3V 2.5 TH Q102 RTL035N03 BAT+ VCC5-2 L110 6.3u 5 1 2012 R109 0 MTM261100 P100 CDRH4D28CNP-6R3NCT IC110 3.
CASIO COMPUTER CO.,LTD.
