User manual

Changing the Home City
Summer Time Setting
1.
Y
Tap the “EDIFICE Connected” icon.
2.
X
Hold down (C) for at least 1.5 seconds
until [CNCT] starts to flash.
When a connection is established
between the watch and phone, [CNCT]
will stop flashing and the second hand will
move from [R] to
e
.
●
If connection fails for some reason,
[ERR] will appear on the display
momentarily and then the watch will
return to the mode it was in before you
started the connection procedure.
Trying to connect
Connected
3.
Y
Perform the operation shown on the
phone screen to change your Home City
summer time setting.
Checking the Watch Charge
Level
Use the procedure below to check the current
charge level with EDIFICE Connected.
1.
Y
Tap the “EDIFICE Connected” icon.
2.
X
Hold down (C) for at least 1.5 seconds
until [CNCT] starts to flash.
When a connection is established
between the watch and phone, [CNCT]
will stop flashing and the second hand will
move from [R] to
e
.
●
If connection fails for some reason,
[ERR] will appear on the display
momentarily and then the watch will
return to the mode it was in before you
started the connection procedure.
Trying to connect
Connected
3.
Y
Use EDIFICE Connected to check the
charge level.
Connection
Connecting with a Phone
This section explains how to establish a
Bluetooth connection with a phone that is
paired with the watch.
●
If the watch is not paired with the phone you
want to connect with, refer to the information
below and pair them.
l
C
Pair the watch with a phone.
1.
Move the phone close to (within one meter
of) the watch.
2.
X
Hold down (C) for at least 1.5 seconds
until [CNCT] starts to flash.
When a connection is established
between the watch and phone, [CNCT]
will stop flashing and the second hand will
move from [R] to
e
.
●
If connection fails for some reason,
[ERR] will appear on the display
momentarily and then the watch will
return to the mode it was in before you
started the connection procedure.
Trying to connect
Connected
Important!
●
If you have problems establishing a
connection, it could mean that
EDIFICE Connected is not running on
the phone. On the phone’s home
screen, tap the “EDIFICE Connected”
icon. After the app starts up, hold down
the watch’s (C) button for at least 1.5
seconds.
Note
●
The connection will be terminated if
you do not perform any operation on
the watch or phone for a fixed amount
of time.
To specify the connection limit time,
perform the following operation with
EDIFICE Connected: “Watch
settings”
n
“Connection time”. Next,
select a setting of 3 minutes, 5 minutes,
or 10 minutes.
Disconnecting from a Phone
Pressing any button will terminate a Bluetooth
connection and return to the Timekeeping
Mode.
Trying to connect
Disconnected
Using the Watch in a Medical Facility
or Aircraft
Whenever you are in a hospital, on an aircraft,
or in any other location where auto signal
receive or connection with a phone may cause
problems, you can perform the procedure
below to disable it. To re-enable auto time
adjustment, perform the same operation
again.
1.
X
If the watch is in any mode besides the
Timekeeping Mode, hold down (D) for at
least two seconds to enter the
Timekeeping Mode.
2.
X
Hold down (A) for about two seconds.
Release the button when your currently
selected Home City appears on the
display.
Home City
3.
X
Press (D) 14 times.
This displays [RCV].
4.
X
Press (E) to select the auto time
adjustment setting you want.
[OFF]: Auto time adjustment disabled.
[ON]: Auto time adjustment enabled.
5.
X
Press (A) to exit the setting screen.
Operation Guide 5582
8