SERVICE MANUAL (without price) ELECTRONIC CASH REGISTER CE-7000 (EX-475B*,C*,D*) FEB.
CONTENTS CE-7000 Page 1. SPECIFICATIONS........................................................................................ 1 2. INITIALIZE (MAC) OPERATION .................................................................. 4 3. F-INIT (FMAC) OPERATION ....................................................................... 4 4. BLOCK DIAGRAM ....................................................................................... 5 5. TO OPEN THE UPPER CASE ...............................................
1. SPECIFICATIONS 1-1. Electrical specifications 120V 0.7 A 0.3 A 0.3 A Max. Min. Power OFF 220V 0.4A 0.2A 0.2A 230V 0.4A 0.2A 0.2A 240V 0.4A 0.2A 0.2A • Power consumption In operation • Memory protection Back-up battery Back-up period Battery life Recharge time VL3032/1F2 90 days (25 °C) Replace the battery every 5 years. 48 hours • Clock & Calendar Accuracy Auto calendar Within ± 30 sec. per month (25 °C) Effective until 2099 A.D. 1-2.
1-4.
DEVICE NAME MODEL NOTE • Slip printer cable PRT-CB-8C Connect Com 2 or 3. (Cable lngth 1.5m) • External printer cable PRT-CB-8A Connect to Com 1,2 or 3. (Cable length 3 m) • External printer cable PRT-CB-8B Connect to Com 1,2 or 3. (Cable length 5 m) • Power unit for External printer PS-170 Epson model • Power cord for power unit AC-170 Epson model • Power-board JDC model CAUTION Danger of explosion if battery is incorrectly replaced.
2. INITIALIZE (MAC) OPERATION (CE-7000) 1. Plug the power cord into an AC outlet. 2. Set the mode switch to "OFF" position. 3. While pressing the Journal feed Button, turn the mode switch to "PGM" position. 4. Release the Journal feed button. 5. Input the MAC CODE 1. (11 digits) 6. Press "#2" key. (Wait until beep twice.) 7. Input the MAC CODE 2. (3 digits) 8. Press "#2" key. (Initialization receipt is issued.) 9. Initialize operation is executed.
4. BLOCK DIAGRAM 4-1.
4-2.
5. TO OPEN THE UPPER CASE 1. Open the printer cover. Then, remove the ribbon cover from the machine. Open the printer cover. Remove the ribbon cover. 2. Remove the 2 screws of the upper case. Remove the 2 screws. 3. Push the 3 dots marking point at the right side of lower case. At the same time, slide the upper case to the front side. Slide the upper case to the front side. Press the 3 dots marking point. 4. Open upper case from the left side.
5. The each parts of the Main PCB are located as shown in the picture. RAM 1 (128 K bytes) Reset Switch Flash ROM 1 (2 M bytes) Printer cable Battery Power supply connector Buzzer Flash ROM 2 (512 K bytes) CPU RAM 4 (Option RAM-610) Display cable Clerk key connector RAM 3 (Option RAM-610) COM 1 port Flash pack connector for Memory cassette RAC-9 Keyboard select switch Main PCB NOTE: RAM2 (128 K bytes) is located on the back side of Main PCB. 6.
6.CIRCUIT EXPLANATION 6-1. Power supply circuit The power supply circuit provides the following voltage for the main circuit. Output Pin No1----Output Pin No.2---Output Pin No.3---Output Pin No.4---- VC1 (DC32.3V): VC2 (DC24V): VLED (DC5.85V): GND: To the VC line for the Display power. To the Vp line for the printer power. To the Vcc,Vcc2 and Vdd for the logic circuit power. Signal GND. The power switch SW1 is located at the right side of the lowercase.
6-2. Reset and power down circuit The rest and power down circuit are as following circuit. The reset switch is provided for the hard reset to cleare the system error. Use this switch only when the FMAC or MAC are not possible to perform. Reset switch The position of Reset switch From top of view From rear of view Printer The mark of reset switch 6-3.
CPU pin description(uPD784215GC-084-8EU) Pin No.
Pin No. 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 Signal Name P83 P84 P85 P86 P87 P40 P41 P42 P43 P44 P45 P46 P47 P50 P51 P52 P53 P54 P55 P56 P57 VSS P60 P61 P62 P63 P64 P65 P66 P67 VDD P100 P101 P102 P103 P30 P31 P32 P33 P34 P35 P36 P37 TEST P90 P91 P92 P93 P94 P95 RB3 RB4/CB1 FB0/CB2 FB1 FB2 D0 D1 D2 D3 D4 D5 D6 D7 A8 A9 A10 A11 A12 A13 A14 A15 GND A16 A17 A18 A19 RD WR WAIT ASTB VDD BUZZER R.
6-4. Memory chip selection circuit The RAM chip select signals made by the following circuit. There are 4 chip enable signal lines for RAM selection and 3 chip enable signal lines for Flash ROM selection (including Memory cassette). RAM1 CE RAM2 CE RAM3 CE RAM4 CE RAM1 CE is for RAM 1 chip enable signal. RB1 RB2 RB3 RB4/CB1 FB1 RAM enable ARC RESET RAM1 selection The RAM1 is selected by the RAM enable signal "H" and the 2CS signal " L" of output pin No.13 .
6-5. Flash ROM1 address circuit The Flash ROM1 address signals FA17 to FA20 are made by the following circuit. The Flash ROM1 (LH28F016SCT-L95, 16M bits) is used for the application program. Flash ROM1 (16M bits) CPU address A19 A18 A17 H L L L H H L BANK port FC2 FC1 L L L L H X FC0 L H X BANK H L L X L H X 3 H 4 H Common L H H H H X Flash FA20 0 L 1 L 2 A18 memory address FA19 FA18 FA17 L A18 A17 H A18 A17 A17 L L L H L A18 A18 L A17 A17 L NOTE Memory block No.
6-7. Flash Pack circuit (Memory Cassette RAC-9) The Memory Cassette RAC-9 (2 M bytes) is possible to connect to the Flash Pack connector CN17 of the Main PCB E475-1.
6-8. Memory map The memory table is as follows: RAM enable H H H H H H L X X X X H H 2CS 3CS 4CS 8CS CCS A18 A19 RAM BANK No.
6-9. Printer drive circuit The printer drive circuit is as follows: IC5 (MTA001M-F4101) is the head pin driver IC. And, the Transistors Q6,Q7 and Q8 are the motor drive circuit. The IC1 (TA8429H) is the auto paper cut driver circuit. 6-10.
6-11.
6-12. Keyboard selection switch The main PCB has the keyboard selection switch to detect the keyboard type. For the model CE-7000, set the switch to S position for the stroke key type. Keyboard selection switch 6-10. To mount optional circuit The following optional circuits are provided for this model. 1. Clerk key circuit 2. Multi-drawer circuit 3. Paper near end sensor circuit 1) Clerk key circuit NOTE1 : This circuit is mounted from factory for the destination Germany.
1-3. Connect the clerk key cable sub ass'y to the clerk key unit. Also, fix the FG wire by the fixing pin and the screw. Clerk cable sub ass'y Clerk key unit Pin No. Wire color Printed mark on PCB 1 Red C 2 White 1 3 Blue 2 4 Yellow 4 5 Green 8 1-4. Insert the clerk switch unit to the clerk key case. Turn 2 times Ferrite core Clerk key case 1-5. Cut off the masking plate of clerk key unit of lower case. Then, set the clerk key case and unit to the lower case.
1-6. Remove the clerk button unit form the upper case. Then, replace the model key plate. Remove the mode key plate. Then, fix new mode key plate. Upper case 2) Multi-drawer kit 2-1. Prepare the following parts kit for multi-drawer circuit. The parts kits are supplied from sales division. MDL-10 Multi-drawer kit 2-2. Check whether the parts of multi-drawer kit are as follows: Code No.
2-4. Open the back cover of lower cabe to release the 2 screws. Then, connect the necessary extension cable for drawer. In this case, do no forget to fix the FG wire of the extension cable to the frame ground by the screw. Release the 2 screws and open the back cover of lower case. Connect the extension drawer cable to the drawer connector. Fix the FG wire of the extension drawer cable by screw of the parts kit. 2-5. Connect 1 pin FG connector of the drawer extension cable to the drawer 1 pin connector.
3-3. Fix the paper near end sensor to the lower case by 2 screws and connect the sensor connector to the main PCB. 1903 0101 19077906 62366288 1907 6948 Main PCB 2P connector 6-14.
Pin No.
6-16. DC/DC converter circuit There are two DC/DC convertor circuit for display. For the 7 segment display voltages are made by the DC/DC converter in display PCB E445B-E2. Transistor Q3 is oscillating and zener diode ZD3 feedbacks the output voltage to control the oscilation. VC For the dot display voltages are made by the DC/DC converter in display PCB E445B-E2. Transistor Q1,Q2 ,IC6 and DC/DC converter transformer T1. The dot display MN12832E need the following Voltages. 1.
Pin No.Pin Name N a m e 1 A0/nMUX 2 A1 3 A2/ALE 4 5 6 8 9 10 11 12 AD0 AD1 AD2 D3 D4 D5 D6 D7 27 nRD/nDS 26 nWR/DIR 23 nRESET 24 nINTR 25 nCS 18 nPULSE1 19 nPULSE2 In/Out Status of OFF Status of ON Status of ON Description No Token Token Address 0-2 In L L Pulse On a non-multiplexed bus, these signals are directly connected to the lower 3 bits of the address bus.
Pin No.Pin Name N a m e 20 RXIN 21 nTXEN 16 XTAL1 17 XTAL2 15 28 7 14 22 VDD VDD VSS VSS VSS In/Out Status of OFF Status of ON Status of ON Description No Token Token Receive IN In L H Pulse Receive input. This signal carries the receive data information from the line receiver circuitry to the COM20019. nTransmit Out L L Pulse Transmit Enable output. Enable This signal used in backplane mode to enable the line driver for transmission.
3. In-line connection 1) System connection diagram The maximum In-line (ARCNET) cable length and maximum connection unit will be varied by the In-line communication speed as shown below: NOTE: The terminater 100 ohms is necessary to mount at the end of In-line cable . Total In-line cable length is max. A m. Terminater (100 ohms) Terminater (100 ohms) In line communication speed (Baud rate) Maximum connection unit Maximum cable length A ( m ) 312.5 K bps 156.
4) To connect the In-line cable Connect the In-line cable and connector as shown below: Connector at the enc of In-line cable Terminal cap Red In-line connector In-line cable Wrap bent shield wire with Copper tape. Black Shield wire Terminater (100 ohms) Notes: 1. Use crimp tool for connecting terminal caps. 2. If crimp tool is not available, connect the wires with solder instead of terminal cap. After the soldering, insulate the wires with vinyl tape.
In-line port (ARCNET) Release the 2 screws to remove the bachk cover. Connect the In-line cable shield wire to FG plate. To connect the In-line cable, release the 2 screws from the back cover. Then, remove the Back cover. And, put the In-line connector to the ARCNET In-line port. Do not foget to connect the shield wire (copper tape part) to the FG plate by the cable supporter with screw. 5) Specification of the In-line cable 1.
7. DIAGNOSTIC OPERATION 7-1. To start the diagnostic program 1. Plug the power cord into an AC outlet. 2. Set the mode switch to "OFF" position. 3. While pressing the "Jounal feed " button, turn the mode switch to "PRG" position. 4. Release the "Journal feed" button. 5. Input "99990000" and press "ST" ("#2" key). 6. Diagnostic program is executed. 7-2. Check item The following test can be checked in the diagnostic test. 1. Key code test 2. Switch status test 3. Individul function test 7-3.
7-4. Switch status test Press "C" button or changing the switch condition,the switch status is appeared on the transaction place of the display. The clerk key switch condition is shown at the 6 and 7 digit number's place of display. For the clerk button model, the pressed LED will light on.
7-5. Individual function test 1) Series test This test will perform the following tests in series. 1. Display test (All dot and segment trun on.) 2. RAM read after write test (one time) 3. Print test (one time) 4. Time display test 5. Drawer open test 6. Receipt issue test 7. Display test (1234567890 display) Operation : X 1 #2 Key Function X : 0= Automatic RAM capacity detection 1= RAM1 (128K) test only 2= RAM1,2 (128K) test 4= RAM1,2,3 (RAM3 is 512K.) test 6= RAM1,2,3,4 (RAM3,4 are 512K.
2) Print aging test (R/J printer) This test will check the R/J printer continuously until pressing some key button or turn off the mode switch. Operation : n1 Y X 2 #2 Key X: 0= Print 45 times test pattern without paper cut in a minute. 1= Print 15 times test pattern with paper cut in a minute. Y: 0= Normal print 1= Continuously print n1: 0= Display test pattern 1= All dots and segment will light on.
5) Print test (R/J printer) This test will check the R/J printer. To stop the continuous printing, press some key button or turn off the mode switch. Operation : n1 n 0 X 0 #2 Key X: 0= One time print 1= Continuously print n: 0= Display test pattern 1= All dots and segment will light on.
8) Flash1 ROM check This test will check the Flash 1 ROM. This test will print the version name and check sum on the receipt as shown in sample print. When using several bank, the each version name and check sum will be printed after this sample data. Operation : 9 0 0 #2 Key [PRINT] [DISPLAY] Dot display DIAG MODE QA version Segment display 9) Printer auto paper cut check This test will check the auto paper cut function.
11) Flash2 ROM and Flash pack check This test will check the Flash 2 ROM and Flash pack. This test will perform the erase, write, and verify check. Operation : n1 n2 s n X 3 #2 Key s: 0= Select Flash2 1= Select Flash pack X: 5= Test by one block (64 bytes) Select the block by the Number n (from 0 to 9). When the block is over 9, use the number n1 and n2. 6= Test the all block. After test, the all block data is cleared. In this case, number n will have the following function select.
12) Flash ROM and Flash pack device information check This test will check the Flash ROM and Flash pack device infromation . Thie device signature code (Maker code, device code) and write protect information will be printed on the receipt.
14) RAM read only check This test will check the read only check for RAM. Perform the RAM check (EX: command "1 and #2 " ), before start of this operation. Operation : X 5 #2 Key X: 0= One time check. 1= Continuous check. To stop the test, set the mode switch to OFF. NOTE: During the RAM test, the Receipt switch LED is blinking. [PRINT] [DISPLAY] Dot display Segment display 15) RAM read write check This test will check the read write check for RAM.
16) RS232 port check This test will check the RS232 port. Connect the loop back connector before operate this check. Operation : X 2 m 7 #2 Key m: 0= One time loop check 1= Loop check continuously 2= One time loop check (Ignore the CD,CI signals. Only COM1 port) 3= Loop check continuously (Ignore the CD,CI signals. Only COM1 port) X: 0= COM1 1= COM2 2= COM3 3= IN-LINE port Test details 1) Check of the control shignals (CTS,DSR,RTS,DTR,CD,CI) Low/High level.
17) Print check This test will check the print test. Operation : s 0 0 r 8 #2 Key r: 0= One time check 1= Continuously check (NOTE1) s: 0= Receipt/Journal print mutually 1= Receipt print only 2= Journal print only NOTE1: To stop this test, press any key or set the mode switch to OFF position. [PRINT] [DISPLAY] Dot display DIAG MODE QA version Segment display 18) All charactor print check This test will print the all charactors of the controller.
NOTE: When use the command print and display, press #1 key (Cash AMT tender key) to display and print the next line. To stop this test, press any key or set the mode switch to OFF position. [PRINT] [DISPLAY] Dot display DIAG MODE QA version Segment display 19) All charactor display check This test will display the all charactors of the controller. Operation : X n n 2 7 0 8 #2 Key nn: 00= Display the all charactors without wait time. 01= Display the all charactors with 40 msec. wait time.
20) Dot display check This test will display the some dot test pattern. Operation : n z y y 6 7 0 8 #2 Key z: 0= Pattern selection 1= Pattern selection 2= Pattern selection 3= Pattern selection n: n= After n dot lines, reverse the dot condition. 0= After 16 dot lines, reverse the dot condition. yy:00= Change the test pattern each about 1 sec. 01= Change the test pattern each 160 msec. 09= Change the test pattern each 9 X 160 msec.
22) Date time set test The machine will set the time or the date. Opeartion : n1 n2 n3 n4 n5 n6 X 9 #2 Key X: 0= Time set (n1 n2: Time, n3 n4: Minute, n5 n6: Second) 1= Date set (n1 n2: Year, N3 n4: Month, n5 n6: Day) [PRINT] [DISPLAY] Dot display Segment display 23) IPL flash pack down load test This operation will store the application software in the flash 1 to the flash pack by IPL format. The flash pack is cleared the all data inside it.
24) Scanner test This operation will test the scanner operation. Opeartion : X n 3 0 7 #2 Key n: 0= Scanner read test Scanner read some bar code by this command. #1 key will change the LED light on/off control. 1= Compare the read data test. (Compare with code "49491004".) X: 0= 2,400 bps and even parity 1= 9,600 bps and even parity 2= 2,400 bps and odd parity 3= 9,600 bps and odd parity NOTE: To stop this opeartion, press any or trun off the mode key switch.
Opeartion : z z b m 7 2 b: Baud rate selection 0= 19,200 bps 1= 9,600 bps X 7 #2 2= 4,800bps m: Test Mode selection 0= Self loop test 1= Reception mode Key 3= 2,400bps 4= 38,400 bps 2= Send mode ZZ: Time out number (seconds) input between data (default is 3 seconds. Input ZZ, ZZ seconds will be the time of time out.) X: 0= Normally select 0. 1= When error is happened, print error receipt before retry operation. Test procedure 1) Operate the send machine first.
26) In-line (ARCNET) test This operation will test the In-line (ARCNET) function.
2) MODE 2 Reception mode 2: Check the receive data only. Send mode 2 : Send the test data each one second continuously. This action will continue until making the stop operation. RETRY OPERATION 1) Reception side: (Reception mode 1 is selected.) Until 7 times continuous error, retry the reception. Over 8 times continuous error, issue the error receipt. 2) Send side : (Send mode 1 is selected.) If there are no answer from reception machine, the machine will wait after 3 seconds, retry 7 times send operation.
27) In-line (ARCNET) initial test This operation will initialize the In-line (ARCNET) function. And , when the machine is connected to the other machine, the token signal is sent to the other machine.
8. ERROR CODE 8-1.Operation error code When an error condition is generated, one of the following error codes (E001 – E205) is displayed to indicate the cause of the error and the corrective action.
Error code Message Meaning E049 CHECK memory full Check tracking index memory full. E050 DETAIL memory full Check tracking detail memory full. Attempt to made use to open a new CHK/TBL No. is E051 check using a number that is already used for an existing occupied check in check tracking memory. Attempt made to use reopen a new check CHK/TBL No. is not using a number that is not used for an existing check in E053 opened check tracking memory. Out of CHK/TBL No.
8-2. System error code Error Meaning code File I/O errors 750 File cannot be created. 751 No designated drive 752 FCB area shortage of flash memory 753 No appropriate record number is designated. 754 No partation exists. 755 No vacant record is remained. 756 Changing is not permitted. 757 The designate file cannot be found. 758 The same file has already existed. 759 The same page has already existed. 760 No vacant record is remained. The contents of internal memory and memory cassette are 762 different.
9. IC DATA 1. BA10393F-E2 2. HA17431PA 3. HD74LVC244ATELL Don't care High impedance 4.
5. HD74LVC374ATELL 6. HIN202CBN-T 7.
8. HY628100ALLG-70 9.
10.
11.
12. LM2576HVT-5.0LB03 13. MB3800PF Pin No. Name Description Input for Error Amp. Soft start/ SPC preset capacitor terminal Power supply Output current preset/ control terminal Output terminal (totem pole type) GND Oscillation friquency preset capacitor/ resister connection terminal Error amp.
14. MTA001M-F4101 15. S-80823ANNP-EDL/S-80835ALNP-EAZ (2) CMOS active low output (1) Nch open drain active low output S-808XX AX XX - XXX - T2 Tape spec. IC direction Production short No. Package No. NP: SC-82AB MP: SOT-23-5 UP: SOT-89-3 Y: TO-92 Output N: Nch open drain (Active "L") L: CMOS (Active "L") Detection Voltage X 10 times 16.
17. SN74HC157APWR 18. SN74HC27PWR 19. SN74LV00APWR 20.
21. SN74LV08APWR 22. SN74LV138APWR 23.
24. SN74LV165APWR 25.
26. SN74LV244APWR 27. SN74LV245APWR 28.
29. SN74LV373APWT-EL 30. SN74LV373APWT-EL 31.
32. SN751178NS-EL Input Enable Output 33.
34.
10.
MAIN PCB (Back side) - 68 -
11. CIRCUIT DIAGRAM MODEL : CE-7000 (EX-475B*,C*,D*) CONTENTS 1. LOCATION OF PRINTED CIRCUIT BOARD................................................................... 70 2. MAIN PCB CIRCUIT ........................................................................................................ 72 2-1. MAIN PCB CIRCUIT (1/6) ........................................................................................ 72 2-2. MAIN PCB CIRCUIT (2/6) .................................................................
- 70 UK Europe, other countries Germany
- 71 USA, Canada
- 72 -
- 73 -
- 74 -
- 75 -
- 76 -
- 77 -
- 78 -
- 79 -
- 80 -
- 81 -
- 82 -
- 83 -
- 84 I/O PB-14 (ARCNET)
- 85 -
- 86 -
- 87 -
- 88 -
- 89 -
- 90 -
- 91 -
12. PARTS LIST PARTS LIST MODEL : CE-7000 (EX-475B*,C*,D*) CONTENTS Explode view ................................................................................................................... 93 1. MAIN PCB BLOCK ....................................................................................................... 2. MAIN DISPLAY BLOCK ............................................................................................... 3. CUSTOMER DISPLAY BLOCK............................................
10 4 93 3 37 64 6 C CA 0 E-7 00 64A SIO 5 58 64A 9 7 8 101 60 57 100 49 2 48 61 59 36 13 39 29 34 47 21 11 33 32 31 12 9 8 7 5 4 19 30 6 27 3 2 1 .
62 63 75 44 98 43 80 99 46 40 80 41 90 96 97 42 92 82 45 87 80 88 91 78 79 100 89 83 55 56 72 70 69 71 81 84 54 95 100 1 74 74 76 76 68 51 67 53 Battery only 52 66 50 65 94 73 86 RAC-9 77 102 - 94 - 85
N Item Code No. Parts Name Specification Q'ty Europe N N N N N N N N N N N N N N N N N N N N N N N 1.
N Item Code No.
N Item Code No.
N Item Code No. Parts Name Specification Q'ty Europe N N N 34 35 36 37 37 38 39 %#/NS C CA/AMT CH CHK/TEND CLK# CPN CR1 CR2 DEP1 DEP1 DEP10 DEP10 DEP11 DEP12 DEP13 DEP14 DEP15 DEP16 DEP17 DEP18 DEP19 DEP2 DEP2 DEP20 DEP21 DEP22 DEP23 DEP24 DEP25 DEP26 DEP27 DEP28 DEP29 DEP3 DEP3 DEP30 DEP4 DEP4 DEP5 DEP5 DEP6 DEP6 DEP7 DEP7 DEP8 DEP8 DEP9 DEP9 ERR.
N Item Code No. Parts Name Specification Q'ty Europe N N N F1 F1 N F2 N F3 IC1 IC2 N T1 N D1 N D2 D3 D4 Q1 ZD1 N C1 C5 N C6 C7 N C8 N C9 N N FT1 L1 N SW1 N SW2 N SW2 N N N N N Q1 R1 R2 R3 N N N N N N N N IC1 5.
N Item Code No.
N Item Code No. Parts Name Specification Q'ty Europe N N N N N N N N N 86 62481646 GUIDE/ROM E475 CLIP CONTACT CONTACT CONTACT CONTACT CONTACT/PIN HOUSING HOUSING HOUSING HOUSING INSERT/BIT LABEL/CONNECTOR E475 SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW TAPE TIE/INSULOCK TUBE/UL TUBE/UL WASHER WIRE WIRE 13.
- 102 - 541 539 524 529 532 537 706 721 720 530 525 520 540 536 531 526 543 535 724 723 723 525 716 533 525 723 527 531 532 538 534 528 705 138 128 133 147 113 130 129 135 510 102 136 103 708 707 511 513 514 111 142 512 515 139 140 106 516 112 519 104 134 137 108 517 518 107 114 508 105 509 510 124 120 118 121 123 906 503 116 903 901 109 115 504 130 122 117 904 507 505 RIBBON CASSET 102 101 127 906 126 EXPLODED DIAGRAM FO
PARTS PRICE LIST M-U420(071) N N N N N N Item Code No.
N N N N N N Item 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 Code No.
16.
N N N N N N N N N N N N N N N N N N N N N N N N N N N DL-2766 (M type) Europe, Saudi-Arabia, Other countries Item Code No.
DL-2767 (M type) UK, Germany - 107 -
N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N DL-2767 (M type) UK, Germany Item Code No.
DL-2417 (M type) USA - 109 -
N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N DL-2417 (M type) USA Item Code No.
DL-2517 (M type) Canada - 111 -
N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N DL-2517 (M type) Canada Item Code No.
DL-3616 (L type) USA, Canada - 113 -
DL-3616 (L type) USA, Canada N Item Code No. Parts name Specification Q'ty Price Code RANK 2 19077272 LOCK ASSY ZD00290-0 1 BZ B 3 19060672 NUT M4XP0.
DL-3617 (L type) Saudi-Arabia - 115 -
DL-3617 (L type) Saudi-Arabia N Item Code No. Parts name Specification 2 19077935 LOCK ASSY ZD00280-0 3 19060672 NUT M4XP0.
CASIO TECHNO CO.,LTD. Overseas Service Division Nishi-Shinjuku Kimuraya Bldg.
