Operation Manual

39
AT&W n Stores the current settings. Only n = 0 can be specified (can be omitted). AT&W0
OK
AT&W
OK
AT&W?
ERROR
AT&W ＝ ?
ERROR
AT ＊DANTE Displays the FOMA terminal
signal reception level.
0： FOMA terminal signal reception level is displayed as
out of area.
1： FOMA terminal signal reception level is 0 or 1
bar.
2： FOMA terminal signal reception level is 2 bars.
3： FOMA terminal signal reception level is 3 bars.
AT ＊DANTE
＊DANTE:3
OK
AT ＊DANTE ＝?
＊DANTE:(0-3)
OK
AT ＊DGANSM= n Sets the reject/permit mode
setting for the packet
incoming call. This
command is effective for
those incoming packet calls
after the setting command is
input.
n =0 ： Disables the incoming call reject (AT ＊
DGARL)/permit setting (AT ＊ DGAPL) (initial
value).
n =1 ： Enables the incoming call reject
setting.
n =2 ： Enables the incoming call permit
setting.
AT ＊DGANSM?
： Displays the current setting.
AT ＊DGANSM=0
OK
AT ＊DGANSM?
＊DGANSM:0
OK
AT ＊ DGAPL= n [,cid]
Sets APN, which permits
incoming packet calls, by
using <cid> parameter
defined by
+CGDCONT
n =0 ： Adds the APN defined by <cid> to
incoming call permission list.
n = 1 : Deletes the APN defined by <cid>
from incoming call permission list.
If <cid> is omitted, this will apply to all cid.
AT ＊DGAPL?
： Displays incoming call permission list.
AT ＊DGAPL =0,5
OK
AT ＊DGAPL?
＊DGAPL:1
OK
AT ＊DGAPL =1
OK
AT ＊DGAPL?
OK
AT ＊ DGARL= n [,cid] Sets APN, which rejects
incoming packet calls, by
using <cid> parameter
defined by
+CGDCONT
n = 0 : Adds the APN defined by <cid> to
incoming call rejection list.
n = 1 : Deletes the APN defined by <cid>
from incoming call rejection list.
If <cid> is omitted, this will apply to all cid.
AT ＊DGARL?
： Displays incoming call rejection list.
AT ＊DGARL =0,5
OK
AT ＊DGARL?
＊DGARL:1
OK
AT ＊DGARL =1
OK
AT ＊DGARL?
OK
AT ＊DGPIR= n This command validates the
setting for notifying Caller ID
when sending/receiving
packet communication.
Even in the dial up network
setting, you can also add
186 (notify) or 184 (not
notify) to the access point
number. (p.27)
n = 0 : Uses APN as it is (initial value).
n = 1 : Uses APN by adding "184". (Caller ID
is always not sent.)
n = 2 : Uses APN by adding "186". (Caller ID
is always sent.)
AT ＊DGPIR?
：Displays the current setting.
AT ＊DGPIR =0
OK
AT ＊DGPIR?
＊DGPIR:0
OK
AT ＊DRPW Displays the indicator value
of the receiving power of the
FOMA terminal.
−
AT ＊DRPW
＊DRPW:0
OK
AT ＊DRPW=?
＊DRPW:(0-75)
OK
AT+CAOC Inquires for the current
charge.
−
AT+CAOC
+CAOC:"000014"
OK
AT command Outline Parameter/description Command execution example
CA-01C_E_Manual_02.fm 39 ページ ２０１１年５月３日 火曜日 午後１２時３０分