User manual

User’s Guide 5526 (MRG)
E-15
Time Zone setting
Important!
x In order to prevent loss of water resistance and damage due to impact, make sure that the crown is
fully pushed in to its normal position after operating it.
x For details about summer time settings and time zone settings, refer to the Operation Guide available
at the CASIO website.
http://world.casio.com/manual/wat/
E-14
Using the Watch in a Medical Facility or Aircraft
x Disable auto time adjustment whenever you are in a medical facility, and aircraft, in any other area
where radio wave reception and connection with a phone are prohibited or restricted.
x Disabling auto time adjustment disables time calibration signal auto receive and auto connection with
a phone.
x Press B once and then pull out the crown to the first click. The second hand will move to Y (YES)
(auto receive enabled) or N (NO) (auto receive disabled). To disable auto time adjustment, rotate the
crown to move the second hand to N (NO). To enable auto time adjustment, rotate the crown to
move the second hand to Y (YES). After the setting is the way you want, push the crown back in to its
normal position.
30
E-13
C
Stopwatch Mode Countdown Timer Mode
30
x Start
x Stop
Seconds
x Reset x Enters the
Countdown
Timer Mode
Points to ST
Hours
Minutes
Hours
(0 to 24)
C
30
x Start
x Stop
Seconds
x Reset x Enters the
Alarm Mode
Points to TR
Hours
Minutes
Hours
(0 to 24)
C
Alarm Mode
* The A-side of the dial indicates an a.m. time, while
the P-side indicates a p.m. time.
x Hold down C for about four seconds to establish
a Bluetooth connection with a phone. For details,
refer to the Operation Guide available at the CASIO
website.
http://world.casio.com/manual/wat/
30
x Illumination
Alarm on
x Alarm off x Enters the
Timekeeping
Mode
Points to AL
Hours
Minutes
Hours
(0 to 24)
x Holding down C for two seconds in any mode returns to the Timekeeping Mode.
E-12
Mode Reference Guide
x Use C to navigate between modes.
Timekeeping Mode
30
Minute hand
Day of the week
hand
24-hour hand
Hour hand
Second hand
Day Indicator
Crown
CB
A
Dual time hour hand
Dual time 24-hour hand*
Dual time minute hand
x Pressing A turns on the illumination.
x To swap your Home Time with the Dual Time,
hold down A for threeseconds.
x To view the result of last time calibration by
time signal reception or Mobile Link, press
B once.
x To trigger a time calibration by Mobile Link
manually, hold down B for 0.5seconds.
x To trigger a time calibration signal reception
operation manually, hold down B for
1.5seconds.
x To search for the phone (while the watch
is connected with it), hold down B for
3.5seconds.
x Press C once to enter the Stopwatch Mode.
C
E-11
Time Calibration Signal Manual Receive
1. Hold down B for at least two seconds until the second hand moves
to RC (Receive). If the second hand is a position other than RC, keep
B depressed until it moves to RC.
2. Place the watch near a window.
x The time setting will be adjusted automatically when a signal receive
operation is successful.
x Calibration signal reception normally takes anywhere from about two
to 10 minutes. It can take as long as 20 minutes.
x Best reception is in the middle of the night.
x If you are unable to receive a signal, check the Operation Guide
available at the CASIO website to ensure the watch is in a suitable
location.
http://world.casio.com/manual/wat/
30
Second hand
E-10
Time Calibration Signal Auto Receive
Important!
x To perform time calibration signal auto receive, the watch must be in the Timekeeping Mode. See
“Mode Reference Guide” (page E-12).
●
Leave the watch in a location that is appropriate for time calibration signal reception between
the hours of midnight and 5:00 a.m. See “Appropriate Signal Reception Location (Time
Calibration Signal)” (page E-9).
x The second hand will point to RC while time calibration signal reception is in progress.
x Reception normally takes anywhere from about two to ten minutes, but it can take as long as
20minutes.
x When the receive operation is successful, the time and day settings will be adjusted automatically.
E-9
Timekeeping (Based on a Time Calibration Signal)
Appropriate Signal Reception Location (Time Calibration Signal)
x Keep the watch away from metal and position it so its 6 o’clock side is
facing a window. Avoid moving the watch as much as possible and do
not perform any watch operations while a signal receive operation is in
progress.
●
You may experience time calibration signal reception problems in
the areas described below.
- Among or near buildings
- While riding in a vehicle
- Near household appliances, office machines, mobile phones, etc.
- On a construction site, in an airport, or any other location where radio
wave interference occurs
- Near high-voltage lines
- In mountainous areas or behind a mountain
x Always check the time setting on the day there should be a switch
between standard time and summer time (DST). If the setting is not
correct (due to signal reception failure), turn DST on or off manually as
required.
6 o’clock
E-8
Timekeeping (Current Time and Day Adjustment)
●
Timekeeping is kept accurate using information provided by a time calibration signal and by
communication with a mobile phone.
x Time calibration signals can be received using Auto Receive or Manual Receive (page E-9).
x To set the current time and day, normally use the procedure under “Time Calibration Signal Auto
Receive” (page E-10).
x For information about how to adjust time using a phone, refer to the Operation Guide available at
the website below.
http://world.casio.com/manual/wat/
x If you are in an area where a time calibration signal cannot be received or if you cannot connect
with a phone for some reason, adjust time and date settings manually (page E-18).
Important!
x If you feel that the current time and/or day indicator are not in the correct positions, you can adjust
their alignment. For details, see the Operation Guide available at the CASIO website.
x Time calibration signal reception is normally possible in the areas below.
Japan, China, North America, Europe
For details, see the Operation Guide available at the CASIO website.
x For details about the following operations, refer to the Operation Guide available at the CASIO website:
Configuring Home City time differential (time zone), summer time, current time, and current date
settings manually.
http://world.casio.com/manual/wat/