User manual

ManualsBrandsCasio ManualsWatch5411

Basic Operations

This section provides an overview of the

watch and its operations.

Note

●

The illustrations included in this

manual have been created to

facilitate explanation. An

illustration may differ somewhat

from the item it represents.

General Guide

③①②

⑤

④

⑥⑦⑧

⑨

Hour hand

Second hand

Minute hand

24-hour hand

Small minute hand

Small hour hand

Mode hand

Day indicator

Crown

Watch Face Items

①

②

③

④

⑤

⑥

⑦

⑨

⑧

⑩

⑪

⑫

⑬

Signal receive result

Alarm off

Alarm on

Time calibration reception in

progress

GPS signal time information and

position information acquisition in

progress

GPS signal time information

reception in progress

Summer time setting

MA1409-EB

Approximate latitude

(N side: North latitude, S side: South

latitude)

Day of the week

Airplane Mode

Stopwatch Mode

Timer Mode

Alarm Mode

Navigating Between Modes

Your watch has four modes.

You tell which mode the watch is

currently in by checking the position of

the mode hand.

●

Timekeeping Mode (normal

timekeeping): Current day of the week

●

Stopwatch Mode: ST (STW)

●

Timer Mode: TR

●

Alarm Mode: AL

Timekeeping Mode

Mode hand

Alarm Mode

Timer Mode

Stopwatch Mode

Use the (C) button to navigate between

modes.

●

Hold down (C) for at least two seconds

to return to the Timekeeping Mode.

●

Holding down (C) for four seconds or

longer will enter or exit the Airplane

Mode. The mode hand points to h

while the watch is in the Airplane Mode.

l Using the Watch on an Aircraft

Using the Crown

The watch’s crown is a screw-in (screw

lock) type. To use the crown, you first

need to rotate it towards you (leftwards)

to loosen it.

Loosen

Crown

Important!

●

To prevent loss of water

resistance and/or damage due

to impact, be sure to push the

crown in and lock it when not in

use.

●

When pushing the crown back

in, take care not to apply too

much force.

●

Fast Forward/Fast Reverse

Normal position

Second click

First click

Crown

After pulling out the crown to the first or

second click, rotating it quickly in

succession in either direction will start a

fast forward or fast reverse operation.

While a fast forward operation is in

progress, quickly rotating the crown in

succession again will increase the speed

even further.

●

The fast reverse operation speed is

fixed and cannot be changed.

●

Stopping Fast Forward/Fast

Reverse

Rotate the crown in the direction

opposite that of the ongoing operation or

press any button.

Operation Guide 5411

Summary of content (15 pages)

PAGE 1
© 2014 CASIO COMPUTER CO., LTD. MA1409-EB Operation Guide 5411 Basic Operations This section provides an overview of the watch and its operations. I Day of the week J Airplane Mode Note ● H Approximate latitude (N side: North latitude, S side: South latitude) The illustrations included in this manual have been created to facilitate explanation. An illustration may differ somewhat from the item it represents. Using the Crown The watch’s crown is a screw-in (screw lock) type.
PAGE 2
Operation Guide 5411 Note ● If you do not perform any operation for about two minutes after pulling out the crown, crown operations will automatically become disabled. If that happens, push the crown back in and then pull it out again. While you are wearing the watch, make sure that its face (solar panel) is not blocked from the light by the sleeve of your clothing. Power generation efficiency is reduced even when the face of the watch is blocked only partially.
PAGE 3
Operation Guide 5411 Checking the Charge Level Power Saving Function The charge level is indicated by watch hand movement. Functions become disabled as battery power goes low. Leaving the watch in a dark location for about one hour between the hours of 10 p.m. and 6 a.m. will cause the second hand to stop, and the watch will enter Level 1 power saving. If the watch is left in this condition for six or seven days, all hands will stop and the watch will enter Level 2 power saving.
PAGE 4
Operation Guide 5411 Time Adjustment Using GPS Appropriate Signal Reception Location GPS signal reception is possible outdoors where the sky is visible and not blocked by buildings, trees, or other objects. Acquiring GPS Position Information Manually ● You can use a button operation to acquire GPS position information and adjust your Home City (time zone), time, and day settings in accordance with your current location.
PAGE 5
Operation Guide 5411 ● Acquiring GPS Time Information Manually You can use a button operation on the watch to receive GPS signal time information. When the receive operation is successful, the watch’s Home City (time zone), day, and time settings will be adjusted accordingly. If information acquisition is successful, the second hand will move to “YES”, and then the watch will automatically adjust its time and day settings. ● GPS signal reception requires large amounts of power.
PAGE 6
Operation Guide 5411 Time Adjustment Using a Time Calibration Signal Time Calibration Signal Reception Ranges Auto Time Calibration Signal Receive Appropriate Signal Reception Location Time calibration signal reception is supported in the areas shown below. A time calibration signal can be received while the watch is near a window. ● An automatic time calibration signal receive operation is performed and the time and day settings are adjusted between midnight and 5:00 a.m.
PAGE 7
Operation Guide 5411 Checking the Receive Operation Result You can use the procedure below to check the result of the last GPS or time calibration signal receive operation. ● Getting ready ー l Navigating Between Modes The second hand will move and indicate the receive operation result. (GPS signal reception also is not possible at Level 1.
PAGE 8
Operation Guide 5411 2. Rotate the crown to change the time zone. The small hour hand and small minute hand indicate the current time in the selected time zone. ● ● Hold down the (B) button for about one second to display UTC (Universal Time Coordinated) time. 2. Press (B) to reset the elapsed time to all zeroes. Note ● When a time zone for which there is no city name displayed is selected, use “STD” or “DST” for the summer time setting. 3. Press (C) three times to return to the Timekeeping Mode.
PAGE 9
Operation Guide 5411 Using the Timer 1. Press (A) to start the countdown. 1. Pull out the crown to the first click. This turns on the alarm. 2. Rotate the crown to change the alarm 30 time setting. Alarm on countdown is reached. 2. Press any button to stop the tone. 3. Press (C) twice to return to the Timekeeping Mode. Alarms The watch will beep when the alarm time is reached. ● 30 To pause an ongoing countdown, press (A). To reset a paused countdown to the start time, press (B).
PAGE 10
Operation Guide 5411 Note ● The initial factory default summer time setting for all cities (time zones) is “AT (AUTO)”. With this setting, the watch automatically switches between summer time and standard time as required. The “AT (AUTO)” setting lets you use the watch without worrying about 3. Hold down (A) for about one second to change the summer time setting. ● Each press of (A) cycles through available settings in the sequence shown below. “AT (AUTO)” n “STD” n “DST” ● 1.
PAGE 11
Operation Guide 5411 8. Press (C). This changes to the month setting operation. 11 12 2 ＋ 9 3 4 8 7 6 7. Press (C). Confirm that the day indicator shows 1. 1. Pull out the crown to the second click. 2. Hold down (B) for about five 1 10 Adjusting Hand and Day Indicator Alignment − 5 Month 9. Rotate the crown to change the month. seconds, until the second hand moves to 12 o’clock. This will start auto alignment of the hour hand, minute hand, second hand, and 24-hour hand.
PAGE 12
Operation Guide 5411 ● Other Information Prior to Takeoff 1. Enter the watch’s Airplane Mode when instructed to do so by airline personnel. 30 City code City (Time Zone) List A time zone for which no city name is displayed by the watch is indicated in the table below by a hyphen (-) in the “City Code” column. The “City Name” column will contain the name of a representative city in that zone. Airplane mark City code UTC ● After Arriving 1. Exit the Airplane Mode. 2.
PAGE 13
Operation Guide 5411 City Name Summer Time Start Summer Time End London 2:00 a.m., last 1:00 a.m., last Sunday in Sunday in March October Paris 3:00 a.m., last 2:00 a.m., last Sunday in Sunday in March October Athens 4:00 a.m., last 3:00 a.m., last Sunday in Sunday in March October Sydney 2:00 a.m., first Sunday in October 3:00 a.m., first Sunday in April 2:00 a.m., last Wellington Sunday in September 3:00 a.m., first Sunday in April Los Angeles 2:00 a.m., 2:00 a.m.
PAGE 14
Operation Guide 5411 Signal Reception (Time Calibration Signal) The watch cannot perform a receive operation. Q1 Q2 Is the watch in a location that is appropriate for signal reception? Check your surroundings and move the watch to a location where signal reception is better. Is the watch’s battery charged? Signals reception is not possible YES while battery power is low. Keep the watch exposed to light until it recharges sufficiently.
PAGE 15
Operation Guide 5411 Q5 Hands are stopped and buttons do not work. The watch is in the charge recovery mode. Wait until the recovery process is complete (for about 15 minutes). The watch will recover more quickly if you place it in a brightly lit location. Q6 The current time displayed by the watch is off by a few hours. The city (time zone) setting is not correct. Select the correct setting.