User manual

1
Operation Guide ANA(3H3E-3)
MA1301-EA
© 2013 CASIO COMPUTER CO., LTD.
• Be sure to keep all user documentation handy for future reference.
• Your watch may differ somewhat from the one shown in the
illustration.
Notes
• Some water resistant models are equipped
with a screw lock crown.
• With such models, you must unscrew the
crown in the direction noted in the illustration
to loosen it before you can pull it out. Do not
pull too forcibly on such crowns.
• Also note that such watches are not water
resistant while their crowns are loosened. Be
sure to screw the crowns back in as far as
they will go after making any setting.
Setting the Time and Day
To set the day
1. Pull the crown out to
Click1.
2. Rotate the crown to set
the day.
Avoid changing the day
setting between 9:00p.m.
and 1:00a.m. (If you do,
the day indication may
not change at midnight).
3. Push the crown back in to
the normal position.
To set the day of the
week and time
1. Pull the crown out to
Click2 when the second
hand is at 12o’clock. The
second hand will stop.
2. Set the hands by rotating
the crown. As you do, the
day of the week changes
accordingly.
3. After setting the day
of the week, rotate the
crown to set the time.
Make sure to distinguish
between AM and PM.
4. On a time signal, push
the crown back in to the
normal position.
24-Hour Hand
The 24-Hour Hand indicates
the current hour of the day.
It makes one complete
rotation every 24hours.
Module 1343/2364/5071/5316/5354
Crown
(Normal position)
Click 1
(Day setting)
Click 2
(Time and
day of week
setting)
Day
24-Hour Hand
Day of the week
Module 1794/5072
Crown
(Normal position)
Click 1
(Day setting)
Click 2
(Time and
day of week
setting)
Day
24-Hour Hand
Day of the week
Module 5224
Crown
(Normal position)
Click 1
(Day setting)
Click 2
(Time and
day of week
setting)
Day of the week
Day
24-Hour Hand
■ For watch with the elapsed time bezel
Rotate the elapsed time bezel to align the
mark with the minute hand.
After certain amount of time elapsed, read the
graduation on the elapsed time bezel which the
minute hand points to.
The elapsed time is indicated.
Elapsed time bezel
Specifications
Module No.
Accuracy at normal
temperature
Battery
type
Battery life
1343/5316/5354 ±20 seconds per month SR916SW Approx. 3 years
1794/2364 ±20 seconds per month SR621SW Approx. 2 years
5071/5072 ±20 seconds per month SR621SW Approx. 3 years
5224 ±20 seconds per month SR920SW Approx. 3 years
Operating Precautions
Water Resistance
• The following applies to watches with WATER RESIST or WATER
RESISTANT marked on the back cover.
Water
Resistance
Under
Daily Use
Enhanced Water Resistance Under
Daily Use
5
Atmospheres
10
Atmospheres
20
Atmospheres
Marking
On watch front
or on back
cover
No
BAR
mark
5BAR 10BAR 20BAR
Example
of Daily
Use
Hand washing,
rain
Yes Yes Yes Yes
Water-related
work, swimming
No Yes Yes Yes
Windsurfing No No Yes Yes
Skin diving No No Yes Yes
• Do not use this watch for scuba diving or other types of diving that
requires air tanks.
• Watches that do not have WATER RESIST or WATER RESISTANT
marked on the back cover are not protected against the effects
of sweat. Avoid using such a watch under conditions where it will
be exposed to large amounts of sweat or moisture, or to direct
splashing with water.
• Even if a watch is water-resistant, do not operate its buttons or
crown while it is submersed in water or wet.
• Even if a watch is water-resistant, avoid wearing it in the bath or
in areas where detergents (soap, shampoo, etc.) are being used.
Such conditions can reduce water resistance.
• After submersion in seawater, use plain water to rinse all salt and
dirt from the watch.
• To maintain water resistance, have the gaskets of your watch
replaced periodically (about once every two or three years).
• A trained technician will know how to check your watch for
proper water resistance whenever you have its battery replaced.
Battery replacement requires the use of special tools. Always
request battery replacement from your original retailer or from an
authorized CASIO Service Center.
• Some water-resistant watches come with fashionable leather
bands. Avoid swimming, washing, or any other activity that causes
direct exposure of a leather band to water.
• The inside surface of the watch glass may fog when the watch is
exposed to a sudden drop in temperature. No problem is indicated
if the fogging clears up relatively quickly. If the fogging does not
clear or if water has gotten into the watch, take it in for repair
immediately.
• Continued use of the watch with water inside can result in damage
to electronic and mechanical components, the face of the watch,
etc.
• Your water-resistant watch has been tested in accordance with the
International Organization for Standardization regulations ISO2281
and FTC (USA) “GUIDE FOR THE WATCH INDUSTRY.” Guide 5.
Band
• Tightening the band too tightly can cause you to sweat and make
it difficult for air to pass under the band, which can lead to skin
irritation. Do not fasten the band too tightly. There should be
enough room between the band and your wrist so you can insert
your finger.
• Deterioration, rust, or corrosion of the band can cause it to break,
which may result in the watch falling off your wrist and becoming
lost. Be sure to take good care of the band and keep it clean.
Should you notice any breakage, discoloration, looseness or
other problem with the band, immediately contact your original
retailer or an authorized CASIO Service Center to have it checked,
repaired, or replaced. Note that you will be charged for any repair
or replacement of the band.
Temperature
• Never leave the watch on the dashboard of a car, near a heater,
or in any other location that is subject to very high temperatures.
Do not leave the watch where it will be exposed to very low
temperatures, either. Temperature extremes can cause the watch
to lose or gain time, to stop, or otherwise malfunction.