User manual

Inställning av latitud och longitud för din aktuella plats
Du kan försäkra dig om att visningen av tidsinställningarna för solens upp-/nedgång och
månåldrar är korrekt genom att ställa in latitud och longitud för din aktuella plats.
Att välja Hemstad genom att ställa in latitud och longitud
1. I Tidvisningsfunktionen, tryck och håll inne A i minst två
sekunder tills ADJUST visas på den digitala displayen. Detta
är inställningsfunktionen. Släpp A när ADJUST visas. Dina
aktuella Hemstadsdata visas på den digitala displayen med en
blinkande pil (►) till vänster.
2. Tryck A för att visa displayen för latitudinställning med den
aktuella latitudinställningen blinkandes.
Inställning av aktuell tid och datum
Följ proceduren nedan för att justera klockans aktuella tids- och datuminställningar om de
är felaktiga.
Om du ändrar digitala Hemstadsdata bör den analoga tidsinställningen ändras därefter. Om
den analoga tiden inte visar den digitala tiden, ska du kontrollera visarnas grundpositioner
och justera vid behov (sida E-26).
Att ändra inställningar för aktuell tid och datum
1. I Tidvisningsfunktionen, tryck och håll inne A i minst två
sekunder tills ADJUST visas på den digitala displayen. Detta är
inställningsfunktionen. Släpp A när ADJUST visas.
Namnet på staden som du har valt som Hemstad för tillfället
visas på den digitala displayen med en blinkande pil
(►) till vänster.
E-22
Display För att justera: Tryck:
Ändra stadsnamn Använd D (öst) och B (väst).
Växla mellan Sommartid
(DST ON) och Standardtid
(DST OFF) Tryck D.
Växla mellan 12-timmars-
visning (12H) och 24-tim-
marsvisning (24H) Tryck D.
Nollställa sekundvisning Tryck D.
till 00.
Justera timmar och minuter
Justera År, Månad eller Använd D (+) och B (-).
Dag
Välj datumets display-
format (DMY, YMD, MDY) Tryck D.
5. När du har utfört alla önskade inställningar trycker du A två gånger för att återgå till
Tidvisningsfunktionen.
E-24
Justering av grundposition för visare
Denna klockas tim-, minut-, och sekundvisare kan visa fel om de utsätts för stark magne-
tism eller en kraftig stöt. Om detta inträffar kan du följa proceduren nedan för att justera
visarnas positioner.
Att justera grundpositioner
1. I Tidvisningsfunktionen, tryck och håll inne A i minst fyra sek
under tills HAND SET visas på den digitala displayen. Detta är
inställningsfunktionen. Släpp A när HAND SET visas.
Detta får SEC 00 att blinka på den digitala displayen för att
indikera sekundvisarens justeringsfunktion.
5. Tryck A för att lämna inställningsdisplayen.
•Dettafårtim-ochminutvisarnaattyttasigtilldenaktuellatidenförTidvisningsfunktionen.
E-28
Bruksanvisning 5269
3. Använd D (+) och B (-) för att det ändra det blinkande värdet i steg om 0,1°.
• Tryck och håll inne D eller B medan displayen för latitud- eller longitudinställning visas för att scrolla
värdet till vänster om decimalpunkten (värdet till höger ändras inte) med hög hastighet.
4. Om du vill ändra latitudvärdet, tryck C för att visa displayen för longitudinställning med den aktuel-
la longitudinställningen blinkandes.
5. Använd D (+) och B (-) för att det ändra det blinkande värdet i steg om 0,1°.
6. När du har utfört alla önskade inställningar trycker du A för att återgå till Tidvisningsfunktionen.
E-21
2. Använd D och B för att välja önskade stadsdata.
• Välj dina Hemstadsdata innan du ändrar någon annan inställning.
• För komplett information om stadsdata, se ”Stadsdatatabell” på baksidan av denna bruksanvisning.
3.TryckCförattyttablinkandetochväljadeandrainställningarnaisekvensensomvisasnedan.
Stadsdata > DST > 12/24-timmarsvisning > Sekunder > Timmar > Minuter > År >
Månad > Dag > Knappljud på/av > Belysningstid > Datumets displayformat
• Följande steg förklarar endast hur du gör för att ändra tidvisningsinställningar.
4. När tidvisningsinställningen som du vill ändra blinkar, använder du C och/eller C för att ändra den
enligt beskrivningen nedan.
E-23
Observera!
För information om hur du väljer Hemstad och ändrar DST-inställningen, se ”Ändring av Hemstads-
inställningar” (sida E-17).
• Klockans interna helautomatiska kalender tar med månadernas olika antal dagar och skottår i be-
räkningen.Närduharställtindatumetbördetintennasnågonanledningtillattändradet,förutom
när du byter klockans batteri.
• Om du ändrar Hemstadsinställningen kommer latitud- och longitudinställningarna återställas till
platsen för din Hemstad.
E-25
2. Kontrollera sekundvisarens position.
• Sekundvisarens grundposition är korrekt om den pekar på klockan 12.
Om den inte gör det, använd D (framåt) och B (bakåt) för att justera
sekundvisarens position så att den pekar på klockan 12.
  •Tryckochhållinnenågonavknapparnaförattyttasekundvisarenmed
hög hastighet.
3. Tryck C. Detta får 0:00 att blinka på den digitala displayen, vilket
indikerar justeringsfunktionen för timmar och minuter.
4. Kontrollera tim- och minutvisarnas positioner.
• Visarnas grundpositioner är korrekta om de pekar på klockan 12. Om de
inte gör det, använd D (framåt) och B (bakåt) för att justera deras positio
ner.
  •Tryckochhållinnenågonavknapparnaförattyttatim-ochminutvisar
na med hög hastighet.
E-27
Ta ut riktningar
E-20
Confi guring Latitude and Longitude Settings for Your Current Location
You can ensure correct display of sunrise and sunset time settings, and of moon ages
by confi guring latitude and longitude settings for your current location.
To select a Home City by confi guring latitude and longitude settings
1. In the Timekeeping Mode, hold down
A
for at least two
seconds until
ADJUST
appears on the digital display.
This is the setting mode. Release
A
after
ADJUST
appears.
• Your current Home City data will appear on the
digital display with an arrow ( ) fl ashing to the left.
2. Press
A
to display the latitude setting screen with the
current latitude setting fl ashing.
E-21
3. Use
D
(+) and
B
(–) to change the fl ashing value in 0.1° increments.
• Holding down
D
or
B
while the latitude or longitude setting screen is
displayed will scroll the value to the left of the decimal point (the value to the
right does not change) at high speed.
S 62.0° S 61.9° S 0.1° N 0° N 0.1° N 61.9° N 62.0°
4. When the latitude is the value you want, press
C
to display the longitude setting
screen with the current longitude setting fl ashing.
5. Use
D
(+) and
B
(–) to change the fl ashing value in 0.1° increments.
W 179.9° W 179.8° W 0.1° E 0° E 0.1° E 179.9° E 180°
6. When the settings are the way you want, press
A
to return to the Timekeeping
Mode.
E-22
Confi guring Current Time and Date Settings
You can use the procedure below to adjust the current time and date settings if they
are not correct.
Changing the digital Home City data should cause the analog time setting to change
accordingly. If the analog time does not indicate the digital time, check the home
positions of the hands and make adjustments if necessary (page E-26).
To change the current time and date settings
1. In the Timekeeping Mode, hold down
A
for at least two
seconds until
ADJUST
appears on the digital display.
This is the setting mode. Release
A
after
ADJUST
appears.
•
The name of the city currently selected as your Home
City will appear on the digital display with an arrow
(
) fl ashing to the left.
City nameCity name
E-23
2. Use
D
and
B
to select the city data you want.
• Select your Home City data before changing any other setting.
• For full information on city data, see the “City Data Table” at the back of this
manual.
3.
Press
C
to move the fl ashing in the sequence shown below to select the other settings.
DST
Date Display Format
Illumination Duration Button Operation Tone On/Off
Day
12/24-Hour Format
Seconds Hour Minute Year
Month
City data
• The following steps explain how to confi gure timekeeping settings only.
4. When the timekeeping setting you want to change is fl ashing, use
B
and/or
D
to
change it as described below.
E-24
Screen To do this: Do this:
Change the city name
Use
D
(East) and
B
(West).
Toggle between Daylight Saving Time
(
DST ON
) and Standard Time (
DST OFF
).
Press
D
.
Toggle between 12-hour (
12H
) and 24-hour
(
24H
) timekeeping.
Press
D
.
Reset the seconds to
00
Press
D
.
Change the hour or minute
Use
D
(+) and
B
(–).
Change the year, month, or day
Select the date display format (DMY, YMD,
MDY)
Press
D
.
5. When the settings are the way you want, press
A
twice to return to the
Timekeeping Mode.
E-25
Note
• For information about selecting a Home City and confi guring the DST setting, see
“Confi guring Home City Settings” (page E-17).
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to
change it except after you have the watch’s battery replaced.
• Changing your Home City setting will initialize the latitude and longitude settings to
the location of the Home City.
E-26
Hand Home Position Adjustment
The hour, minute, and second hands of this watch can be put out of position by strong
magnetism or strong impact. When this happens, you can use the procedure below to
adjust the hand positions.
To adjust home positions
1. In the Timekeeping Mode, hold down
A
for at least
four seconds until
HAND SET
appears on the digital
display. This is the setting mode. Release
A
after
HAND SET
appears.
• This will cause SEC 00 to fl ash on the digital
display, indicating the second hand adjustment
mode.
Second handSecond hand
E-27
2. Check the position of the second hand.
• If the second hand is pointing to 12 o’clock, it is in
the correct home position. If it isn’t, use
D
(forward)
and
B
(back) to adjust the second hand position
so it points to 12 o’clock.
• Holding down either button will cause the second
hand to move at high speed.
3. Press
C
. This will cause
0:00
to fl ash on the digital
display, indicating the hour and minute adjustment
mode.
4. Check the positions of the hour and minute hands.
• The hands are in the correct home positions if they
are pointing to 12 o’clock. If they aren’t, use
D
(forward) and
B
(back) to adjust their positions.
• Holding down either button will cause the hour and
minute hands to move at high speed.
Correct hour and
minute hand positions
Hour and minute hands
Correct hour and
minute hand positions
Hour and minute hands
E-28
5. Press
A
to exit the setting screen.
• This will cause the hour and minute hands to move to the current Timekeeping
Mode time.
E-29
Taking Direction Readings
The watch has a magnetic sensor that makes it possible to take digital compass
readings. You can use the digital compass to fi nd the direction to a specifi c objective
and to determine your current position.
• See “Magnetic North and True North” (page E-40) for information about the two
types of north. For information about maximizing digital compass accuracy, see
“Calibrating Direction Readings” (page E-34) and “Digital Compass Precautions”
(page E-40).
Operation Guide 5269
E-20
Confi guring Latitude and Longitude Settings for Your Current Location
You can ensure correct display of sunrise and sunset time settings, and of moon ages
by confi guring latitude and longitude settings for your current location.
To select a Home City by confi guring latitude and longitude settings
1. In the Timekeeping Mode, hold down
A
for at least two
seconds until
ADJUST
appears on the digital display.
This is the setting mode. Release
A
after
ADJUST
appears.
• Your current Home City data will appear on the
digital display with an arrow ( ) fl ashing to the left.
2. Press
A
to display the latitude setting screen with the
current latitude setting fl ashing.
E-21
3. Use
D
(+) and
B
(–) to change the fl ashing value in 0.1° increments.
• Holding down
D
or
B
while the latitude or longitude setting screen is
displayed will scroll the value to the left of the decimal point (the value to the
right does not change) at high speed.
S 62.0° S 61.9° S 0.1° N 0° N 0.1° N 61.9° N 62.0°
4. When the latitude is the value you want, press
C
to display the longitude setting
screen with the current longitude setting fl ashing.
5. Use
D
(+) and
B
(–) to change the fl ashing value in 0.1° increments.
W 179.9° W 179.8° W 0.1° E 0° E 0.1° E 179.9° E 180°
6. When the settings are the way you want, press
A
to return to the Timekeeping
Mode.
E-22
Confi guring Current Time and Date Settings
You can use the procedure below to adjust the current time and date settings if they
are not correct.
Changing the digital Home City data should cause the analog time setting to change
accordingly. If the analog time does not indicate the digital time, check the home
positions of the hands and make adjustments if necessary (page E-26).
To change the current time and date settings
1. In the Timekeeping Mode, hold down
A
for at least two
seconds until
ADJUST
appears on the digital display.
This is the setting mode. Release
A
after
ADJUST
appears.
•
The name of the city currently selected as your Home
City will appear on the digital display with an arrow
(
) fl ashing to the left.
City nameCity name
E-23
2. Use
D
and
B
to select the city data you want.
• Select your Home City data before changing any other setting.
• For full information on city data, see the “City Data Table” at the back of this
manual.
3.
Press
C
to move the fl ashing in the sequence shown below to select the other settings.
DST
Date Display Format
Illumination Duration Button Operation Tone On/Off
Day
12/24-Hour Format
Seconds Hour Minute Year
Month
City data
• The following steps explain how to confi gure timekeeping settings only.
4. When the timekeeping setting you want to change is fl ashing, use
B
and/or
D
to
change it as described below.
E-24
Screen To do this: Do this:
Change the city name
Use
D
(East) and
B
(West).
Toggle between Daylight Saving Time
(
DST ON
) and Standard Time (
DST OFF
).
Press
D
.
Toggle between 12-hour (
12H
) and 24-hour
(
24H
) timekeeping.
Press
D
.
Reset the seconds to
00
Press
D
.
Change the hour or minute
Use
D
(+) and
B
(–).
Change the year, month, or day
Select the date display format (DMY, YMD,
MDY)
Press
D
.
5. When the settings are the way you want, press
A
twice to return to the
Timekeeping Mode.
E-25
Note
• For information about selecting a Home City and confi guring the DST setting, see
“Confi guring Home City Settings” (page E-17).
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to
change it except after you have the watch’s battery replaced.
• Changing your Home City setting will initialize the latitude and longitude settings to
the location of the Home City.
E-26
Hand Home Position Adjustment
The hour, minute, and second hands of this watch can be put out of position by strong
magnetism or strong impact. When this happens, you can use the procedure below to
adjust the hand positions.
To adjust home positions
1. In the Timekeeping Mode, hold down
A
for at least
four seconds until
HAND SET
appears on the digital
display. This is the setting mode. Release
A
after
HAND SET
appears.
• This will cause SEC 00 to fl ash on the digital
display, indicating the second hand adjustment
mode.
Second handSecond hand
E-27
2. Check the position of the second hand.
• If the second hand is pointing to 12 o’clock, it is in
the correct home position. If it isn’t, use
D
(forward)
and
B
(back) to adjust the second hand position
so it points to 12 o’clock.
• Holding down either button will cause the second
hand to move at high speed.
3. Press
C
. This will cause
0:00
to fl ash on the digital
display, indicating the hour and minute adjustment
mode.
4. Check the positions of the hour and minute hands.
• The hands are in the correct home positions if they
are pointing to 12 o’clock. If they aren’t, use
D
(forward) and
B
(back) to adjust their positions.
• Holding down either button will cause the hour and
minute hands to move at high speed.
Correct hour and
minute hand positions
Hour and minute hands
Correct hour and
minute hand positions
Hour and minute hands
E-28
5. Press
A
to exit the setting screen.
• This will cause the hour and minute hands to move to the current Timekeeping
Mode time.
E-29
Taking Direction Readings
The watch has a magnetic sensor that makes it possible to take digital compass
readings. You can use the digital compass to fi nd the direction to a specifi c objective
and to determine your current position.
• See “Magnetic North and True North” (page E-40) for information about the two
types of north. For information about maximizing digital compass accuracy, see
“Calibrating Direction Readings” (page E-34) and “Digital Compass Precautions”
(page E-40).
Operation Guide 5269
E-20
Confi guring Latitude and Longitude Settings for Your Current Location
You can ensure correct display of sunrise and sunset time settings, and of moon ages
by confi guring latitude and longitude settings for your current location.
To select a Home City by confi guring latitude and longitude settings
1. In the Timekeeping Mode, hold down
A
for at least two
seconds until
ADJUST
appears on the digital display.
This is the setting mode. Release
A
after
ADJUST
appears.
• Your current Home City data will appear on the
digital display with an arrow ( ) fl ashing to the left.
2. Press
A
to display the latitude setting screen with the
current latitude setting fl ashing.
E-21
3. Use
D
(+) and
B
(–) to change the fl ashing value in 0.1° increments.
• Holding down
D
or
B
while the latitude or longitude setting screen is
displayed will scroll the value to the left of the decimal point (the value to the
right does not change) at high speed.
S 62.0° S 61.9° S 0.1° N 0° N 0.1° N 61.9° N 62.0°
4. When the latitude is the value you want, press
C
to display the longitude setting
screen with the current longitude setting fl ashing.
5. Use
D
(+) and
B
(–) to change the fl ashing value in 0.1° increments.
W 179.9° W 179.8° W 0.1° E 0° E 0.1° E 179.9° E 180°
6. When the settings are the way you want, press
A
to return to the Timekeeping
Mode.
E-22
Confi guring Current Time and Date Settings
You can use the procedure below to adjust the current time and date settings if they
are not correct.
Changing the digital Home City data should cause the analog time setting to change
accordingly. If the analog time does not indicate the digital time, check the home
positions of the hands and make adjustments if necessary (page E-26).
To change the current time and date settings
1. In the Timekeeping Mode, hold down
A
for at least two
seconds until
ADJUST
appears on the digital display.
This is the setting mode. Release
A
after
ADJUST
appears.
•
The name of the city currently selected as your Home
City will appear on the digital display with an arrow
(
) fl ashing to the left.
City nameCity name
E-23
2. Use
D
and
B
to select the city data you want.
• Select your Home City data before changing any other setting.
• For full information on city data, see the “City Data Table” at the back of this
manual.
3.
Press
C
to move the fl ashing in the sequence shown below to select the other settings.
DST
Date Display Format
Illumination Duration Button Operation Tone On/Off
Day
12/24-Hour Format
Seconds Hour Minute Year
Month
City data
• The following steps explain how to confi gure timekeeping settings only.
4. When the timekeeping setting you want to change is fl ashing, use
B
and/or
D
to
change it as described below.
E-24
Screen To do this: Do this:
Change the city name
Use
D
(East) and
B
(West).
Toggle between Daylight Saving Time
(
DST ON
) and Standard Time (
DST OFF
).
Press
D
.
Toggle between 12-hour (
12H
) and 24-hour
(
24H
) timekeeping.
Press
D
.
Reset the seconds to
00
Press
D
.
Change the hour or minute
Use
D
(+) and
B
(–).
Change the year, month, or day
Select the date display format (DMY, YMD,
MDY)
Press
D
.
5. When the settings are the way you want, press
A
twice to return to the
Timekeeping Mode.
E-25
Note
• For information about selecting a Home City and confi guring the DST setting, see
“Confi guring Home City Settings” (page E-17).
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to
change it except after you have the watch’s battery replaced.
• Changing your Home City setting will initialize the latitude and longitude settings to
the location of the Home City.
E-26
Hand Home Position Adjustment
The hour, minute, and second hands of this watch can be put out of position by strong
magnetism or strong impact. When this happens, you can use the procedure below to
adjust the hand positions.
To adjust home positions
1. In the Timekeeping Mode, hold down
A
for at least
four seconds until
HAND SET
appears on the digital
display. This is the setting mode. Release
A
after
HAND SET
appears.
• This will cause SEC 00 to fl ash on the digital
display, indicating the second hand adjustment
mode.
Second handSecond hand
E-27
2. Check the position of the second hand.
• If the second hand is pointing to 12 o’clock, it is in
the correct home position. If it isn’t, use
D
(forward)
and
B
(back) to adjust the second hand position
so it points to 12 o’clock.
• Holding down either button will cause the second
hand to move at high speed.
3. Press
C
. This will cause
0:00
to fl ash on the digital
display, indicating the hour and minute adjustment
mode.
4. Check the positions of the hour and minute hands.
• The hands are in the correct home positions if they
are pointing to 12 o’clock. If they aren’t, use
D
(forward) and
B
(back) to adjust their positions.
• Holding down either button will cause the hour and
minute hands to move at high speed.
Correct hour and
minute hand positions
Hour and minute hands
Correct hour and
minute hand positions
Hour and minute hands
E-28
5. Press
A
to exit the setting screen.
• This will cause the hour and minute hands to move to the current Timekeeping
Mode time.
E-29
Taking Direction Readings
The watch has a magnetic sensor that makes it possible to take digital compass
readings. You can use the digital compass to fi nd the direction to a specifi c objective
and to determine your current position.
• See “Magnetic North and True North” (page E-40) for information about the two
types of north. For information about maximizing digital compass accuracy, see
“Calibrating Direction Readings” (page E-34) and “Digital Compass Precautions”
(page E-40).
Operation Guide 5269
E-20
Confi guring Latitude and Longitude Settings for Your Current Location
You can ensure correct display of sunrise and sunset time settings, and of moon ages
by confi guring latitude and longitude settings for your current location.
To select a Home City by confi guring latitude and longitude settings
1. In the Timekeeping Mode, hold down
A
for at least two
seconds until
ADJUST
appears on the digital display.
This is the setting mode. Release
A
after
ADJUST
appears.
• Your current Home City data will appear on the
digital display with an arrow ( ) fl ashing to the left.
2. Press
A
to display the latitude setting screen with the
current latitude setting fl ashing.
E-21
3. Use
D
(+) and
B
(–) to change the fl ashing value in 0.1° increments.
• Holding down
D
or
B
while the latitude or longitude setting screen is
displayed will scroll the value to the left of the decimal point (the value to the
right does not change) at high speed.
S 62.0° S 61.9° S 0.1° N 0° N 0.1° N 61.9° N 62.0°
4. When the latitude is the value you want, press
C
to display the longitude setting
screen with the current longitude setting fl ashing.
5. Use
D
(+) and
B
(–) to change the fl ashing value in 0.1° increments.
W 179.9° W 179.8° W 0.1° E 0° E 0.1° E 179.9° E 180°
6. When the settings are the way you want, press
A
to return to the Timekeeping
Mode.
E-22
Confi guring Current Time and Date Settings
You can use the procedure below to adjust the current time and date settings if they
are not correct.
Changing the digital Home City data should cause the analog time setting to change
accordingly. If the analog time does not indicate the digital time, check the home
positions of the hands and make adjustments if necessary (page E-26).
To change the current time and date settings
1. In the Timekeeping Mode, hold down
A
for at least two
seconds until
ADJUST
appears on the digital display.
This is the setting mode. Release
A
after
ADJUST
appears.
•
The name of the city currently selected as your Home
City will appear on the digital display with an arrow
(
) fl ashing to the left.
City nameCity name
E-23
2. Use
D
and
B
to select the city data you want.
• Select your Home City data before changing any other setting.
• For full information on city data, see the “City Data Table” at the back of this
manual.
3.
Press
C
to move the fl ashing in the sequence shown below to select the other settings.
DST
Date Display Format
Illumination Duration Button Operation Tone On/Off
Day
12/24-Hour Format
Seconds Hour Minute Year
Month
City data
• The following steps explain how to confi gure timekeeping settings only.
4. When the timekeeping setting you want to change is fl ashing, use
B
and/or
D
to
change it as described below.
E-24
Screen To do this: Do this:
Change the city name
Use
D
(East) and
B
(West).
Toggle between Daylight Saving Time
(
DST ON
) and Standard Time (
DST OFF
).
Press
D
.
Toggle between 12-hour (
12H
) and 24-hour
(
24H
) timekeeping.
Press
D
.
Reset the seconds to
00
Press
D
.
Change the hour or minute
Use
D
(+) and
B
(–).
Change the year, month, or day
Select the date display format (DMY, YMD,
MDY)
Press
D
.
5. When the settings are the way you want, press
A
twice to return to the
Timekeeping Mode.
E-25
Note
• For information about selecting a Home City and confi guring the DST setting, see
“Confi guring Home City Settings” (page E-17).
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to
change it except after you have the watch’s battery replaced.
• Changing your Home City setting will initialize the latitude and longitude settings to
the location of the Home City.
E-26
Hand Home Position Adjustment
The hour, minute, and second hands of this watch can be put out of position by strong
magnetism or strong impact. When this happens, you can use the procedure below to
adjust the hand positions.
To adjust home positions
1. In the Timekeeping Mode, hold down
A
for at least
four seconds until
HAND SET
appears on the digital
display. This is the setting mode. Release
A
after
HAND SET
appears.
• This will cause SEC 00 to fl ash on the digital
display, indicating the second hand adjustment
mode.
Second handSecond hand
E-27
2. Check the position of the second hand.
• If the second hand is pointing to 12 o’clock, it is in
the correct home position. If it isn’t, use
D
(forward)
and
B
(back) to adjust the second hand position
so it points to 12 o’clock.
• Holding down either button will cause the second
hand to move at high speed.
3. Press
C
. This will cause
0:00
to fl ash on the digital
display, indicating the hour and minute adjustment
mode.
4. Check the positions of the hour and minute hands.
• The hands are in the correct home positions if they
are pointing to 12 o’clock. If they aren’t, use
D
(forward) and
B
(back) to adjust their positions.
• Holding down either button will cause the hour and
minute hands to move at high speed.
Correct hour and
minute hand positions
Hour and minute hands
Correct hour and
minute hand positions
Hour and minute hands
E-28
5. Press
A
to exit the setting screen.
• This will cause the hour and minute hands to move to the current Timekeeping
Mode time.
E-29
Taking Direction Readings
The watch has a magnetic sensor that makes it possible to take digital compass
readings. You can use the digital compass to fi nd the direction to a specifi c objective
and to determine your current position.
• See “Magnetic North and True North” (page E-40) for information about the two
types of north. For information about maximizing digital compass accuracy, see
“Calibrating Direction Readings” (page E-34) and “Digital Compass Precautions”
(page E-40).
Operation Guide 5269
E-20
Confi guring Latitude and Longitude Settings for Your Current Location
You can ensure correct display of sunrise and sunset time settings, and of moon ages
by confi guring latitude and longitude settings for your current location.
To select a Home City by confi guring latitude and longitude settings
1. In the Timekeeping Mode, hold down
A
for at least two
seconds until
ADJUST
appears on the digital display.
This is the setting mode. Release
A
after
ADJUST
appears.
• Your current Home City data will appear on the
digital display with an arrow ( ) fl ashing to the left.
2. Press
A
to display the latitude setting screen with the
current latitude setting fl ashing.
E-21
3. Use
D
(+) and
B
(–) to change the fl ashing value in 0.1° increments.
• Holding down
D
or
B
while the latitude or longitude setting screen is
displayed will scroll the value to the left of the decimal point (the value to the
right does not change) at high speed.
S 62.0° S 61.9° S 0.1° N 0° N 0.1° N 61.9° N 62.0°
4. When the latitude is the value you want, press
C
to display the longitude setting
screen with the current longitude setting fl ashing.
5. Use
D
(+) and
B
(–) to change the fl ashing value in 0.1° increments.
W 179.9° W 179.8° W 0.1° E 0° E 0.1° E 179.9° E 180°
6. When the settings are the way you want, press
A
to return to the Timekeeping
Mode.
E-22
Confi guring Current Time and Date Settings
You can use the procedure below to adjust the current time and date settings if they
are not correct.
Changing the digital Home City data should cause the analog time setting to change
accordingly. If the analog time does not indicate the digital time, check the home
positions of the hands and make adjustments if necessary (page E-26).
To change the current time and date settings
1. In the Timekeeping Mode, hold down
A
for at least two
seconds until
ADJUST
appears on the digital display.
This is the setting mode. Release
A
after
ADJUST
appears.
•
The name of the city currently selected as your Home
City will appear on the digital display with an arrow
(
) fl ashing to the left.
City nameCity name
E-23
2. Use
D
and
B
to select the city data you want.
• Select your Home City data before changing any other setting.
• For full information on city data, see the “City Data Table” at the back of this
manual.
3.
Press
C
to move the fl ashing in the sequence shown below to select the other settings.
DST
Date Display Format
Illumination Duration Button Operation Tone On/Off
Day
12/24-Hour Format
Seconds Hour Minute Year
Month
City data
• The following steps explain how to confi gure timekeeping settings only.
4. When the timekeeping setting you want to change is fl ashing, use
B
and/or
D
to
change it as described below.
E-24
Screen To do this: Do this:
Change the city name
Use
D
(East) and
B
(West).
Toggle between Daylight Saving Time
(
DST ON
) and Standard Time (
DST OFF
).
Press
D
.
Toggle between 12-hour (
12H
) and 24-hour
(
24H
) timekeeping.
Press
D
.
Reset the seconds to
00
Press
D
.
Change the hour or minute
Use
D
(+) and
B
(–).
Change the year, month, or day
Select the date display format (DMY, YMD,
MDY)
Press
D
.
5. When the settings are the way you want, press
A
twice to return to the
Timekeeping Mode.
E-25
Note
• For information about selecting a Home City and confi guring the DST setting, see
“Confi guring Home City Settings” (page E-17).
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to
change it except after you have the watch’s battery replaced.
• Changing your Home City setting will initialize the latitude and longitude settings to
the location of the Home City.
E-26
Hand Home Position Adjustment
The hour, minute, and second hands of this watch can be put out of position by strong
magnetism or strong impact. When this happens, you can use the procedure below to
adjust the hand positions.
To adjust home positions
1. In the Timekeeping Mode, hold down
A
for at least
four seconds until
HAND SET
appears on the digital
display. This is the setting mode. Release
A
after
HAND SET
appears.
• This will cause SEC 00 to fl ash on the digital
display, indicating the second hand adjustment
mode.
Second handSecond hand
E-27
2. Check the position of the second hand.
• If the second hand is pointing to 12 o’clock, it is in
the correct home position. If it isn’t, use
D
(forward)
and
B
(back) to adjust the second hand position
so it points to 12 o’clock.
• Holding down either button will cause the second
hand to move at high speed.
3. Press
C
. This will cause
0:00
to fl ash on the digital
display, indicating the hour and minute adjustment
mode.
4. Check the positions of the hour and minute hands.
• The hands are in the correct home positions if they
are pointing to 12 o’clock. If they aren’t, use
D
(forward) and
B
(back) to adjust their positions.
• Holding down either button will cause the hour and
minute hands to move at high speed.
Correct hour and
minute hand positions
Hour and minute hands
Correct hour and
minute hand positions
Hour and minute hands
E-28
5. Press
A
to exit the setting screen.
• This will cause the hour and minute hands to move to the current Timekeeping
Mode time.
E-29
Taking Direction Readings
The watch has a magnetic sensor that makes it possible to take digital compass
readings. You can use the digital compass to fi nd the direction to a specifi c objective
and to determine your current position.
• See “Magnetic North and True North” (page E-40) for information about the two
types of north. For information about maximizing digital compass accuracy, see
“Calibrating Direction Readings” (page E-34) and “Digital Compass Precautions”
(page E-40).
Operation Guide 5269
E-20
Confi guring Latitude and Longitude Settings for Your Current Location
You can ensure correct display of sunrise and sunset time settings, and of moon ages
by confi guring latitude and longitude settings for your current location.
To select a Home City by confi guring latitude and longitude settings
1. In the Timekeeping Mode, hold down
A
for at least two
seconds until
ADJUST
appears on the digital display.
This is the setting mode. Release
A
after
ADJUST
appears.
• Your current Home City data will appear on the
digital display with an arrow ( ) fl ashing to the left.
2. Press
A
to display the latitude setting screen with the
current latitude setting fl ashing.
E-21
3. Use
D
(+) and
B
(–) to change the fl ashing value in 0.1° increments.
• Holding down
D
or
B
while the latitude or longitude setting screen is
displayed will scroll the value to the left of the decimal point (the value to the
right does not change) at high speed.
S 62.0° S 61.9° S 0.1° N 0° N 0.1° N 61.9° N 62.0°
4. When the latitude is the value you want, press
C
to display the longitude setting
screen with the current longitude setting fl ashing.
5. Use
D
(+) and
B
(–) to change the fl ashing value in 0.1° increments.
W 179.9° W 179.8° W 0.1° E 0° E 0.1° E 179.9° E 180°
6. When the settings are the way you want, press
A
to return to the Timekeeping
Mode.
E-22
Confi guring Current Time and Date Settings
You can use the procedure below to adjust the current time and date settings if they
are not correct.
Changing the digital Home City data should cause the analog time setting to change
accordingly. If the analog time does not indicate the digital time, check the home
positions of the hands and make adjustments if necessary (page E-26).
To change the current time and date settings
1. In the Timekeeping Mode, hold down
A
for at least two
seconds until
ADJUST
appears on the digital display.
This is the setting mode. Release
A
after
ADJUST
appears.
•
The name of the city currently selected as your Home
City will appear on the digital display with an arrow
(
) fl ashing to the left.
City nameCity name
E-23
2. Use
D
and
B
to select the city data you want.
• Select your Home City data before changing any other setting.
• For full information on city data, see the “City Data Table” at the back of this
manual.
3.
Press
C
to move the fl ashing in the sequence shown below to select the other settings.
DST
Date Display Format
Illumination Duration Button Operation Tone On/Off
Day
12/24-Hour Format
Seconds Hour Minute Year
Month
City data
• The following steps explain how to confi gure timekeeping settings only.
4. When the timekeeping setting you want to change is fl ashing, use
B
and/or
D
to
change it as described below.
E-24
Screen To do this: Do this:
Change the city name
Use
D
(East) and
B
(West).
Toggle between Daylight Saving Time
(
DST ON
) and Standard Time (
DST OFF
).
Press
D
.
Toggle between 12-hour (
12H
) and 24-hour
(
24H
) timekeeping.
Press
D
.
Reset the seconds to
00
Press
D
.
Change the hour or minute
Use
D
(+) and
B
(–).
Change the year, month, or day
Select the date display format (DMY, YMD,
MDY)
Press
D
.
5. When the settings are the way you want, press
A
twice to return to the
Timekeeping Mode.
E-25
Note
• For information about selecting a Home City and confi guring the DST setting, see
“Confi guring Home City Settings” (page E-17).
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to
change it except after you have the watch’s battery replaced.
• Changing your Home City setting will initialize the latitude and longitude settings to
the location of the Home City.
E-26
Hand Home Position Adjustment
The hour, minute, and second hands of this watch can be put out of position by strong
magnetism or strong impact. When this happens, you can use the procedure below to
adjust the hand positions.
To adjust home positions
1. In the Timekeeping Mode, hold down
A
for at least
four seconds until
HAND SET
appears on the digital
display. This is the setting mode. Release
A
after
HAND SET
appears.
• This will cause SEC 00 to fl ash on the digital
display, indicating the second hand adjustment
mode.
Second handSecond hand
E-27
2. Check the position of the second hand.
• If the second hand is pointing to 12 o’clock, it is in
the correct home position. If it isn’t, use
D
(forward)
and
B
(back) to adjust the second hand position
so it points to 12 o’clock.
• Holding down either button will cause the second
hand to move at high speed.
3. Press
C
. This will cause
0:00
to fl ash on the digital
display, indicating the hour and minute adjustment
mode.
4. Check the positions of the hour and minute hands.
• The hands are in the correct home positions if they
are pointing to 12 o’clock. If they aren’t, use
D
(forward) and
B
(back) to adjust their positions.
• Holding down either button will cause the hour and
minute hands to move at high speed.
Correct hour and
minute hand positions
Hour and minute hands
Correct hour and
minute hand positions
Hour and minute hands
E-28
5. Press
A
to exit the setting screen.
• This will cause the hour and minute hands to move to the current Timekeeping
Mode time.
E-29
Taking Direction Readings
The watch has a magnetic sensor that makes it possible to take digital compass
readings. You can use the digital compass to fi nd the direction to a specifi c objective
and to determine your current position.
• See “Magnetic North and True North” (page E-40) for information about the two
types of north. For information about maximizing digital compass accuracy, see
“Calibrating Direction Readings” (page E-34) and “Digital Compass Precautions”
(page E-40).
Operation Guide 5269
E-20
Confi guring Latitude and Longitude Settings for Your Current Location
You can ensure correct display of sunrise and sunset time settings, and of moon ages
by confi guring latitude and longitude settings for your current location.
To select a Home City by confi guring latitude and longitude settings
1. In the Timekeeping Mode, hold down
A
for at least two
seconds until
ADJUST
appears on the digital display.
This is the setting mode. Release
A
after
ADJUST
appears.
• Your current Home City data will appear on the
digital display with an arrow ( ) fl ashing to the left.
2. Press
A
to display the latitude setting screen with the
current latitude setting fl ashing.
E-21
3. Use
D
(+) and
B
(–) to change the fl ashing value in 0.1° increments.
• Holding down
D
or
B
while the latitude or longitude setting screen is
displayed will scroll the value to the left of the decimal point (the value to the
right does not change) at high speed.
S 62.0° S 61.9° S 0.1° N 0° N 0.1° N 61.9° N 62.0°
4. When the latitude is the value you want, press
C
to display the longitude setting
screen with the current longitude setting fl ashing.
5. Use
D
(+) and
B
(–) to change the fl ashing value in 0.1° increments.
W 179.9° W 179.8° W 0.1° E 0° E 0.1° E 179.9° E 180°
6. When the settings are the way you want, press
A
to return to the Timekeeping
Mode.
E-22
Confi guring Current Time and Date Settings
You can use the procedure below to adjust the current time and date settings if they
are not correct.
Changing the digital Home City data should cause the analog time setting to change
accordingly. If the analog time does not indicate the digital time, check the home
positions of the hands and make adjustments if necessary (page E-26).
To change the current time and date settings
1. In the Timekeeping Mode, hold down
A
for at least two
seconds until
ADJUST
appears on the digital display.
This is the setting mode. Release
A
after
ADJUST
appears.
•
The name of the city currently selected as your Home
City will appear on the digital display with an arrow
(
) fl ashing to the left.
City nameCity name
E-23
2. Use
D
and
B
to select the city data you want.
• Select your Home City data before changing any other setting.
• For full information on city data, see the “City Data Table” at the back of this
manual.
3.
Press
C
to move the fl ashing in the sequence shown below to select the other settings.
DST
Date Display Format
Illumination Duration Button Operation Tone On/Off
Day
12/24-Hour Format
Seconds Hour Minute Year
Month
City data
• The following steps explain how to confi gure timekeeping settings only.
4. When the timekeeping setting you want to change is fl ashing, use
B
and/or
D
to
change it as described below.
E-24
Screen To do this: Do this:
Change the city name
Use
D
(East) and
B
(West).
Toggle between Daylight Saving Time
(
DST ON
) and Standard Time (
DST OFF
).
Press
D
.
Toggle between 12-hour (
12H
) and 24-hour
(
24H
) timekeeping.
Press
D
.
Reset the seconds to
00
Press
D
.
Change the hour or minute
Use
D
(+) and
B
(–).
Change the year, month, or day
Select the date display format (DMY, YMD,
MDY)
Press
D
.
5. When the settings are the way you want, press
A
twice to return to the
Timekeeping Mode.
E-25
Note
• For information about selecting a Home City and confi guring the DST setting, see
“Confi guring Home City Settings” (page E-17).
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to
change it except after you have the watch’s battery replaced.
• Changing your Home City setting will initialize the latitude and longitude settings to
the location of the Home City.
E-26
Hand Home Position Adjustment
The hour, minute, and second hands of this watch can be put out of position by strong
magnetism or strong impact. When this happens, you can use the procedure below to
adjust the hand positions.
To adjust home positions
1. In the Timekeeping Mode, hold down
A
for at least
four seconds until
HAND SET
appears on the digital
display. This is the setting mode. Release
A
after
HAND SET
appears.
• This will cause SEC 00 to fl ash on the digital
display, indicating the second hand adjustment
mode.
Second handSecond hand
E-27
2. Check the position of the second hand.
• If the second hand is pointing to 12 o’clock, it is in
the correct home position. If it isn’t, use
D
(forward)
and
B
(back) to adjust the second hand position
so it points to 12 o’clock.
• Holding down either button will cause the second
hand to move at high speed.
3. Press
C
. This will cause
0:00
to fl ash on the digital
display, indicating the hour and minute adjustment
mode.
4. Check the positions of the hour and minute hands.
• The hands are in the correct home positions if they
are pointing to 12 o’clock. If they aren’t, use
D
(forward) and
B
(back) to adjust their positions.
• Holding down either button will cause the hour and
minute hands to move at high speed.
Correct hour and
minute hand positions
Hour and minute hands
Correct hour and
minute hand positions
Hour and minute hands
E-28
5. Press
A
to exit the setting screen.
• This will cause the hour and minute hands to move to the current Timekeeping
Mode time.
E-29
Taking Direction Readings
The watch has a magnetic sensor that makes it possible to take digital compass
readings. You can use the digital compass to fi nd the direction to a specifi c objective
and to determine your current position.
• See “Magnetic North and True North” (page E-40) for information about the two
types of north. For information about maximizing digital compass accuracy, see
“Calibrating Direction Readings” (page E-34) and “Digital Compass Precautions”
(page E-40).
Operation Guide 5269
E-20
Confi guring Latitude and Longitude Settings for Your Current Location
You can ensure correct display of sunrise and sunset time settings, and of moon ages
by confi guring latitude and longitude settings for your current location.
To select a Home City by confi guring latitude and longitude settings
1. In the Timekeeping Mode, hold down
A
for at least two
seconds until
ADJUST
appears on the digital display.
This is the setting mode. Release
A
after
ADJUST
appears.
• Your current Home City data will appear on the
digital display with an arrow ( ) fl ashing to the left.
2. Press
A
to display the latitude setting screen with the
current latitude setting fl ashing.
E-21
3. Use
D
(+) and
B
(–) to change the fl ashing value in 0.1° increments.
• Holding down
D
or
B
while the latitude or longitude setting screen is
displayed will scroll the value to the left of the decimal point (the value to the
right does not change) at high speed.
S 62.0° S 61.9° S 0.1° N 0° N 0.1° N 61.9° N 62.0°
4. When the latitude is the value you want, press
C
to display the longitude setting
screen with the current longitude setting fl ashing.
5. Use
D
(+) and
B
(–) to change the fl ashing value in 0.1° increments.
W 179.9° W 179.8° W 0.1° E 0° E 0.1° E 179.9° E 180°
6. When the settings are the way you want, press
A
to return to the Timekeeping
Mode.
E-22
Confi guring Current Time and Date Settings
You can use the procedure below to adjust the current time and date settings if they
are not correct.
Changing the digital Home City data should cause the analog time setting to change
accordingly. If the analog time does not indicate the digital time, check the home
positions of the hands and make adjustments if necessary (page E-26).
To change the current time and date settings
1. In the Timekeeping Mode, hold down
A
for at least two
seconds until
ADJUST
appears on the digital display.
This is the setting mode. Release
A
after
ADJUST
appears.
•
The name of the city currently selected as your Home
City will appear on the digital display with an arrow
(
) fl ashing to the left.
City nameCity name
E-23
2. Use
D
and
B
to select the city data you want.
• Select your Home City data before changing any other setting.
• For full information on city data, see the “City Data Table” at the back of this
manual.
3.
Press
C
to move the fl ashing in the sequence shown below to select the other settings.
DST
Date Display Format
Illumination Duration Button Operation Tone On/Off
Day
12/24-Hour Format
Seconds Hour Minute Year
Month
City data
• The following steps explain how to confi gure timekeeping settings only.
4. When the timekeeping setting you want to change is fl ashing, use
B
and/or
D
to
change it as described below.
E-24
Screen To do this: Do this:
Change the city name
Use
D
(East) and
B
(West).
Toggle between Daylight Saving Time
(
DST ON
) and Standard Time (
DST OFF
).
Press
D
.
Toggle between 12-hour (
12H
) and 24-hour
(
24H
) timekeeping.
Press
D
.
Reset the seconds to
00
Press
D
.
Change the hour or minute
Use
D
(+) and
B
(–).
Change the year, month, or day
Select the date display format (DMY, YMD,
MDY)
Press
D
.
5. When the settings are the way you want, press
A
twice to return to the
Timekeeping Mode.
E-25
Note
• For information about selecting a Home City and confi guring the DST setting, see
“Confi guring Home City Settings” (page E-17).
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to
change it except after you have the watch’s battery replaced.
• Changing your Home City setting will initialize the latitude and longitude settings to
the location of the Home City.
E-26
Hand Home Position Adjustment
The hour, minute, and second hands of this watch can be put out of position by strong
magnetism or strong impact. When this happens, you can use the procedure below to
adjust the hand positions.
To adjust home positions
1. In the Timekeeping Mode, hold down
A
for at least
four seconds until
HAND SET
appears on the digital
display. This is the setting mode. Release
A
after
HAND SET
appears.
• This will cause SEC 00 to fl ash on the digital
display, indicating the second hand adjustment
mode.
Second handSecond hand
E-27
2. Check the position of the second hand.
• If the second hand is pointing to 12 o’clock, it is in
the correct home position. If it isn’t, use
D
(forward)
and
B
(back) to adjust the second hand position
so it points to 12 o’clock.
• Holding down either button will cause the second
hand to move at high speed.
3. Press
C
. This will cause
0:00
to fl ash on the digital
display, indicating the hour and minute adjustment
mode.
4. Check the positions of the hour and minute hands.
• The hands are in the correct home positions if they
are pointing to 12 o’clock. If they aren’t, use
D
(forward) and
B
(back) to adjust their positions.
• Holding down either button will cause the hour and
minute hands to move at high speed.
Correct hour and
minute hand positions
Hour and minute hands
Correct hour and
minute hand positions
Hour and minute hands
E-28
5. Press
A
to exit the setting screen.
• This will cause the hour and minute hands to move to the current Timekeeping
Mode time.
E-29
Taking Direction Readings
The watch has a magnetic sensor that makes it possible to take digital compass
readings. You can use the digital compass to fi nd the direction to a specifi c objective
and to determine your current position.
• See “Magnetic North and True North” (page E-40) for information about the two
types of north. For information about maximizing digital compass accuracy, see
“Calibrating Direction Readings” (page E-34) and “Digital Compass Precautions”
(page E-40).
Operation Guide 5269
E-20
Confi guring Latitude and Longitude Settings for Your Current Location
You can ensure correct display of sunrise and sunset time settings, and of moon ages
by confi guring latitude and longitude settings for your current location.
To select a Home City by confi guring latitude and longitude settings
1. In the Timekeeping Mode, hold down
A
for at least two
seconds until
ADJUST
appears on the digital display.
This is the setting mode. Release
A
after
ADJUST
appears.
• Your current Home City data will appear on the
digital display with an arrow ( ) fl ashing to the left.
2. Press
A
to display the latitude setting screen with the
current latitude setting fl ashing.
E-21
3. Use
D
(+) and
B
(–) to change the fl ashing value in 0.1° increments.
• Holding down
D
or
B
while the latitude or longitude setting screen is
displayed will scroll the value to the left of the decimal point (the value to the
right does not change) at high speed.
S 62.0° S 61.9° S 0.1° N 0° N 0.1° N 61.9° N 62.0°
4. When the latitude is the value you want, press
C
to display the longitude setting
screen with the current longitude setting fl ashing.
5. Use
D
(+) and
B
(–) to change the fl ashing value in 0.1° increments.
W 179.9° W 179.8° W 0.1° E 0° E 0.1° E 179.9° E 180°
6. When the settings are the way you want, press
A
to return to the Timekeeping
Mode.
E-22
Confi guring Current Time and Date Settings
You can use the procedure below to adjust the current time and date settings if they
are not correct.
Changing the digital Home City data should cause the analog time setting to change
accordingly. If the analog time does not indicate the digital time, check the home
positions of the hands and make adjustments if necessary (page E-26).
To change the current time and date settings
1. In the Timekeeping Mode, hold down
A
for at least two
seconds until
ADJUST
appears on the digital display.
This is the setting mode. Release
A
after
ADJUST
appears.
•
The name of the city currently selected as your Home
City will appear on the digital display with an arrow
(
) fl ashing to the left.
City nameCity name
E-23
2. Use
D
and
B
to select the city data you want.
• Select your Home City data before changing any other setting.
• For full information on city data, see the “City Data Table” at the back of this
manual.
3.
Press
C
to move the fl ashing in the sequence shown below to select the other settings.
DST
Date Display Format
Illumination Duration Button Operation Tone On/Off
Day
12/24-Hour Format
Seconds Hour Minute Year
Month
City data
• The following steps explain how to confi gure timekeeping settings only.
4. When the timekeeping setting you want to change is fl ashing, use
B
and/or
D
to
change it as described below.
E-24
Screen To do this: Do this:
Change the city name
Use
D
(East) and
B
(West).
Toggle between Daylight Saving Time
(
DST ON
) and Standard Time (
DST OFF
).
Press
D
.
Toggle between 12-hour (
12H
) and 24-hour
(
24H
) timekeeping.
Press
D
.
Reset the seconds to
00
Press
D
.
Change the hour or minute
Use
D
(+) and
B
(–).
Change the year, month, or day
Select the date display format (DMY, YMD,
MDY)
Press
D
.
5. When the settings are the way you want, press
A
twice to return to the
Timekeeping Mode.
E-25
Note
• For information about selecting a Home City and confi guring the DST setting, see
“Confi guring Home City Settings” (page E-17).
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to
change it except after you have the watch’s battery replaced.
• Changing your Home City setting will initialize the latitude and longitude settings to
the location of the Home City.
E-26
Hand Home Position Adjustment
The hour, minute, and second hands of this watch can be put out of position by strong
magnetism or strong impact. When this happens, you can use the procedure below to
adjust the hand positions.
To adjust home positions
1. In the Timekeeping Mode, hold down
A
for at least
four seconds until
HAND SET
appears on the digital
display. This is the setting mode. Release
A
after
HAND SET
appears.
• This will cause SEC 00 to fl ash on the digital
display, indicating the second hand adjustment
mode.
Second handSecond hand
E-27
2. Check the position of the second hand.
• If the second hand is pointing to 12 o’clock, it is in
the correct home position. If it isn’t, use
D
(forward)
and
B
(back) to adjust the second hand position
so it points to 12 o’clock.
• Holding down either button will cause the second
hand to move at high speed.
3. Press
C
. This will cause
0:00
to fl ash on the digital
display, indicating the hour and minute adjustment
mode.
4. Check the positions of the hour and minute hands.
• The hands are in the correct home positions if they
are pointing to 12 o’clock. If they aren’t, use
D
(forward) and
B
(back) to adjust their positions.
• Holding down either button will cause the hour and
minute hands to move at high speed.
Correct hour and
minute hand positions
Hour and minute hands
Correct hour and
minute hand positions
Hour and minute hands
E-28
5. Press
A
to exit the setting screen.
• This will cause the hour and minute hands to move to the current Timekeeping
Mode time.
E-29
Taking Direction Readings
The watch has a magnetic sensor that makes it possible to take digital compass
readings. You can use the digital compass to fi nd the direction to a specifi c objective
and to determine your current position.
• See “Magnetic North and True North” (page E-40) for information about the two
types of north. For information about maximizing digital compass accuracy, see
“Calibrating Direction Readings” (page E-34) and “Digital Compass Precautions”
(page E-40).
Operation Guide 5269
E-20
Confi guring Latitude and Longitude Settings for Your Current Location
You can ensure correct display of sunrise and sunset time settings, and of moon ages
by confi guring latitude and longitude settings for your current location.
To select a Home City by confi guring latitude and longitude settings
1. In the Timekeeping Mode, hold down
A
for at least two
seconds until
ADJUST
appears on the digital display.
This is the setting mode. Release
A
after
ADJUST
appears.
• Your current Home City data will appear on the
digital display with an arrow ( ) fl ashing to the left.
2. Press
A
to display the latitude setting screen with the
current latitude setting fl ashing.
E-21
3. Use
D
(+) and
B
(–) to change the fl ashing value in 0.1° increments.
• Holding down
D
or
B
while the latitude or longitude setting screen is
displayed will scroll the value to the left of the decimal point (the value to the
right does not change) at high speed.
S 62.0° S 61.9° S 0.1° N 0° N 0.1° N 61.9° N 62.0°
4. When the latitude is the value you want, press
C
to display the longitude setting
screen with the current longitude setting fl ashing.
5. Use
D
(+) and
B
(–) to change the fl ashing value in 0.1° increments.
W 179.9° W 179.8° W 0.1° E 0° E 0.1° E 179.9° E 180°
6. When the settings are the way you want, press
A
to return to the Timekeeping
Mode.
E-22
Confi guring Current Time and Date Settings
You can use the procedure below to adjust the current time and date settings if they
are not correct.
Changing the digital Home City data should cause the analog time setting to change
accordingly. If the analog time does not indicate the digital time, check the home
positions of the hands and make adjustments if necessary (page E-26).
To change the current time and date settings
1. In the Timekeeping Mode, hold down
A
for at least two
seconds until
ADJUST
appears on the digital display.
This is the setting mode. Release
A
after
ADJUST
appears.
•
The name of the city currently selected as your Home
City will appear on the digital display with an arrow
(
) fl ashing to the left.
City nameCity name
E-23
2. Use
D
and
B
to select the city data you want.
• Select your Home City data before changing any other setting.
• For full information on city data, see the “City Data Table” at the back of this
manual.
3.
Press
C
to move the fl ashing in the sequence shown below to select the other settings.
DST
Date Display Format
Illumination Duration Button Operation Tone On/Off
Day
12/24-Hour Format
Seconds Hour Minute Year
Month
City data
• The following steps explain how to confi gure timekeeping settings only.
4. When the timekeeping setting you want to change is fl ashing, use
B
and/or
D
to
change it as described below.
E-24
Screen To do this: Do this:
Change the city name
Use
D
(East) and
B
(West).
Toggle between Daylight Saving Time
(
DST ON
) and Standard Time (
DST OFF
).
Press
D
.
Toggle between 12-hour (
12H
) and 24-hour
(
24H
) timekeeping.
Press
D
.
Reset the seconds to
00
Press
D
.
Change the hour or minute
Use
D
(+) and
B
(–).
Change the year, month, or day
Select the date display format (DMY, YMD,
MDY)
Press
D
.
5. When the settings are the way you want, press
A
twice to return to the
Timekeeping Mode.
E-25
Note
• For information about selecting a Home City and confi guring the DST setting, see
“Confi guring Home City Settings” (page E-17).
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to
change it except after you have the watch’s battery replaced.
• Changing your Home City setting will initialize the latitude and longitude settings to
the location of the Home City.
E-26
Hand Home Position Adjustment
The hour, minute, and second hands of this watch can be put out of position by strong
magnetism or strong impact. When this happens, you can use the procedure below to
adjust the hand positions.
To adjust home positions
1. In the Timekeeping Mode, hold down
A
for at least
four seconds until
HAND SET
appears on the digital
display. This is the setting mode. Release
A
after
HAND SET
appears.
• This will cause SEC 00 to fl ash on the digital
display, indicating the second hand adjustment
mode.
Second handSecond hand
E-27
2. Check the position of the second hand.
• If the second hand is pointing to 12 o’clock, it is in
the correct home position. If it isn’t, use
D
(forward)
and
B
(back) to adjust the second hand position
so it points to 12 o’clock.
• Holding down either button will cause the second
hand to move at high speed.
3. Press
C
. This will cause
0:00
to fl ash on the digital
display, indicating the hour and minute adjustment
mode.
4. Check the positions of the hour and minute hands.
• The hands are in the correct home positions if they
are pointing to 12 o’clock. If they aren’t, use
D
(forward) and
B
(back) to adjust their positions.
• Holding down either button will cause the hour and
minute hands to move at high speed.
Correct hour and
minute hand positions
Hour and minute hands
Correct hour and
minute hand positions
Hour and minute hands
E-28
5. Press
A
to exit the setting screen.
• This will cause the hour and minute hands to move to the current Timekeeping
Mode time.
E-29
Taking Direction Readings
The watch has a magnetic sensor that makes it possible to take digital compass
readings. You can use the digital compass to fi nd the direction to a specifi c objective
and to determine your current position.
• See “Magnetic North and True North” (page E-40) for information about the two
types of north. For information about maximizing digital compass accuracy, see
“Calibrating Direction Readings” (page E-34) and “Digital Compass Precautions”
(page E-40).
Operation Guide 5269
E-20
Confi guring Latitude and Longitude Settings for Your Current Location
You can ensure correct display of sunrise and sunset time settings, and of moon ages
by confi guring latitude and longitude settings for your current location.
To select a Home City by confi guring latitude and longitude settings
1. In the Timekeeping Mode, hold down
A
for at least two
seconds until
ADJUST
appears on the digital display.
This is the setting mode. Release
A
after
ADJUST
appears.
• Your current Home City data will appear on the
digital display with an arrow ( ) fl ashing to the left.
2. Press
A
to display the latitude setting screen with the
current latitude setting fl ashing.
E-21
3. Use
D
(+) and
B
(–) to change the fl ashing value in 0.1° increments.
• Holding down
D
or
B
while the latitude or longitude setting screen is
displayed will scroll the value to the left of the decimal point (the value to the
right does not change) at high speed.
S 62.0° S 61.9° S 0.1° N 0° N 0.1° N 61.9° N 62.0°
4. When the latitude is the value you want, press
C
to display the longitude setting
screen with the current longitude setting fl ashing.
5. Use
D
(+) and
B
(–) to change the fl ashing value in 0.1° increments.
W 179.9° W 179.8° W 0.1° E 0° E 0.1° E 179.9° E 180°
6. When the settings are the way you want, press
A
to return to the Timekeeping
Mode.
E-22
Confi guring Current Time and Date Settings
You can use the procedure below to adjust the current time and date settings if they
are not correct.
Changing the digital Home City data should cause the analog time setting to change
accordingly. If the analog time does not indicate the digital time, check the home
positions of the hands and make adjustments if necessary (page E-26).
To change the current time and date settings
1. In the Timekeeping Mode, hold down
A
for at least two
seconds until
ADJUST
appears on the digital display.
This is the setting mode. Release
A
after
ADJUST
appears.
•
The name of the city currently selected as your Home
City will appear on the digital display with an arrow
(
) fl ashing to the left.
City nameCity name
E-23
2. Use
D
and
B
to select the city data you want.
• Select your Home City data before changing any other setting.
• For full information on city data, see the “City Data Table” at the back of this
manual.
3.
Press
C
to move the fl ashing in the sequence shown below to select the other settings.
DST
Date Display Format
Illumination Duration Button Operation Tone On/Off
Day
12/24-Hour Format
Seconds Hour Minute Year
Month
City data
• The following steps explain how to confi gure timekeeping settings only.
4. When the timekeeping setting you want to change is fl ashing, use
B
and/or
D
to
change it as described below.
E-24
Screen To do this: Do this:
Change the city name
Use
D
(East) and
B
(West).
Toggle between Daylight Saving Time
(
DST ON
) and Standard Time (
DST OFF
).
Press
D
.
Toggle between 12-hour (
12H
) and 24-hour
(
24H
) timekeeping.
Press
D
.
Reset the seconds to
00
Press
D
.
Change the hour or minute
Use
D
(+) and
B
(–).
Change the year, month, or day
Select the date display format (DMY, YMD,
MDY)
Press
D
.
5. When the settings are the way you want, press
A
twice to return to the
Timekeeping Mode.
E-25
Note
• For information about selecting a Home City and confi guring the DST setting, see
“Confi guring Home City Settings” (page E-17).
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to
change it except after you have the watch’s battery replaced.
• Changing your Home City setting will initialize the latitude and longitude settings to
the location of the Home City.
E-26
Hand Home Position Adjustment
The hour, minute, and second hands of this watch can be put out of position by strong
magnetism or strong impact. When this happens, you can use the procedure below to
adjust the hand positions.
To adjust home positions
1. In the Timekeeping Mode, hold down
A
for at least
four seconds until
HAND SET
appears on the digital
display. This is the setting mode. Release
A
after
HAND SET
appears.
• This will cause SEC 00 to fl ash on the digital
display, indicating the second hand adjustment
mode.
Second handSecond hand
E-27
2. Check the position of the second hand.
• If the second hand is pointing to 12 o’clock, it is in
the correct home position. If it isn’t, use
D
(forward)
and
B
(back) to adjust the second hand position
so it points to 12 o’clock.
• Holding down either button will cause the second
hand to move at high speed.
3. Press
C
. This will cause
0:00
to fl ash on the digital
display, indicating the hour and minute adjustment
mode.
4. Check the positions of the hour and minute hands.
• The hands are in the correct home positions if they
are pointing to 12 o’clock. If they aren’t, use
D
(forward) and
B
(back) to adjust their positions.
• Holding down either button will cause the hour and
minute hands to move at high speed.
Correct hour and
minute hand positions
Hour and minute hands
Correct hour and
minute hand positions
Hour and minute hands
E-28
5. Press
A
to exit the setting screen.
• This will cause the hour and minute hands to move to the current Timekeeping
Mode time.
E-29
Taking Direction Readings
The watch has a magnetic sensor that makes it possible to take digital compass
readings. You can use the digital compass to fi nd the direction to a specifi c objective
and to determine your current position.
• See “Magnetic North and True North” (page E-40) for information about the two
types of north. For information about maximizing digital compass accuracy, see
“Calibrating Direction Readings” (page E-34) and “Digital Compass Precautions”
(page E-40).
Operation Guide 5269
E-20
Confi guring Latitude and Longitude Settings for Your Current Location
You can ensure correct display of sunrise and sunset time settings, and of moon ages
by confi guring latitude and longitude settings for your current location.
To select a Home City by confi guring latitude and longitude settings
1. In the Timekeeping Mode, hold down
A
for at least two
seconds until
ADJUST
appears on the digital display.
This is the setting mode. Release
A
after
ADJUST
appears.
• Your current Home City data will appear on the
digital display with an arrow ( ) fl ashing to the left.
2. Press
A
to display the latitude setting screen with the
current latitude setting fl ashing.
E-21
3. Use
D
(+) and
B
(–) to change the fl ashing value in 0.1° increments.
• Holding down
D
or
B
while the latitude or longitude setting screen is
displayed will scroll the value to the left of the decimal point (the value to the
right does not change) at high speed.
S 62.0° S 61.9° S 0.1° N 0° N 0.1° N 61.9° N 62.0°
4. When the latitude is the value you want, press
C
to display the longitude setting
screen with the current longitude setting fl ashing.
5. Use
D
(+) and
B
(–) to change the fl ashing value in 0.1° increments.
W 179.9° W 179.8° W 0.1° E 0° E 0.1° E 179.9° E 180°
6. When the settings are the way you want, press
A
to return to the Timekeeping
Mode.
E-22
Confi guring Current Time and Date Settings
You can use the procedure below to adjust the current time and date settings if they
are not correct.
Changing the digital Home City data should cause the analog time setting to change
accordingly. If the analog time does not indicate the digital time, check the home
positions of the hands and make adjustments if necessary (page E-26).
To change the current time and date settings
1. In the Timekeeping Mode, hold down
A
for at least two
seconds until
ADJUST
appears on the digital display.
This is the setting mode. Release
A
after
ADJUST
appears.
•
The name of the city currently selected as your Home
City will appear on the digital display with an arrow
(
) fl ashing to the left.
City nameCity name
E-23
2. Use
D
and
B
to select the city data you want.
• Select your Home City data before changing any other setting.
• For full information on city data, see the “City Data Table” at the back of this
manual.
3.
Press
C
to move the fl ashing in the sequence shown below to select the other settings.
DST
Date Display Format
Illumination Duration Button Operation Tone On/Off
Day
12/24-Hour Format
Seconds Hour Minute Year
Month
City data
• The following steps explain how to confi gure timekeeping settings only.
4. When the timekeeping setting you want to change is fl ashing, use
B
and/or
D
to
change it as described below.
E-24
Screen To do this: Do this:
Change the city name
Use
D
(East) and
B
(West).
Toggle between Daylight Saving Time
(
DST ON
) and Standard Time (
DST OFF
).
Press
D
.
Toggle between 12-hour (
12H
) and 24-hour
(
24H
) timekeeping.
Press
D
.
Reset the seconds to
00
Press
D
.
Change the hour or minute
Use
D
(+) and
B
(–).
Change the year, month, or day
Select the date display format (DMY, YMD,
MDY)
Press
D
.
5. When the settings are the way you want, press
A
twice to return to the
Timekeeping Mode.
E-25
Note
• For information about selecting a Home City and confi guring the DST setting, see
“Confi guring Home City Settings” (page E-17).
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to
change it except after you have the watch’s battery replaced.
• Changing your Home City setting will initialize the latitude and longitude settings to
the location of the Home City.
E-26
Hand Home Position Adjustment
The hour, minute, and second hands of this watch can be put out of position by strong
magnetism or strong impact. When this happens, you can use the procedure below to
adjust the hand positions.
To adjust home positions
1. In the Timekeeping Mode, hold down
A
for at least
four seconds until
HAND SET
appears on the digital
display. This is the setting mode. Release
A
after
HAND SET
appears.
• This will cause SEC 00 to fl ash on the digital
display, indicating the second hand adjustment
mode.
Second handSecond hand
E-27
2. Check the position of the second hand.
• If the second hand is pointing to 12 o’clock, it is in
the correct home position. If it isn’t, use
D
(forward)
and
B
(back) to adjust the second hand position
so it points to 12 o’clock.
• Holding down either button will cause the second
hand to move at high speed.
3. Press
C
. This will cause
0:00
to fl ash on the digital
display, indicating the hour and minute adjustment
mode.
4. Check the positions of the hour and minute hands.
• The hands are in the correct home positions if they
are pointing to 12 o’clock. If they aren’t, use
D
(forward) and
B
(back) to adjust their positions.
• Holding down either button will cause the hour and
minute hands to move at high speed.
Correct hour and
minute hand positions
Hour and minute hands
Correct hour and
minute hand positions
Hour and minute hands
E-28
5. Press
A
to exit the setting screen.
• This will cause the hour and minute hands to move to the current Timekeeping
Mode time.
E-29
Taking Direction Readings
The watch has a magnetic sensor that makes it possible to take digital compass
readings. You can use the digital compass to fi nd the direction to a specifi c objective
and to determine your current position.
• See “Magnetic North and True North” (page E-40) for information about the two
types of north. For information about maximizing digital compass accuracy, see
“Calibrating Direction Readings” (page E-34) and “Digital Compass Precautions”
(page E-40).
Operation Guide 5269
Klockan har en magnetisk sensor som gör det möjligt att utföra digitala
kompassmätningar. Du kan använda den digitala kompassen för att ta ut riktningen till
ett visst mål och bestämma din aktuella position.
• Se ”Magnetisk nordpol och Geogrask nordpol” (sida E-40) för information om de
två nordpolstyperna.
För information om du hur du maximerar den digitala kompassens precision, se
”Kalibrering av riktningsavläsningar” (sida E-34) och ”Försiktighetsåtgärder för digital
kompass”
(sida E-40).