User manual

Världstid
Världstiden visar digitalt den aktuella tiden i en av 48 städer (29
tidszoner) världen runt. Med en enkel åtgärd kan du växla din
Hemstad med Världstidsstaden som är vald för tillfället.
• Tiderna i Världstidfunktionen och Tidvisningsfunktionen är syn
kroniserade med varandra. Om du tycker att en tid i Världs
tidfunktionen verkar felaktig ska du kontrollera att du har valt rätt
stad som din Hemstad. Kontrollera även att den aktuella tiden
som visas i Tidvisningsfunktionen är korrekt.
• Tiderna i Världstidfunktionen är baserade på
UTC-tidsskillnader. Se ”Stadskodtabellen” på baksidan av denna
bruksanvisning för information om UTC-tidsskillnaderna som
stöds.
• Alla inställningar i detta avsnitt utförs i Världstidfunktionen som du aktiverar genom att
trycka C (sida E-7).
E-20
Att växla stadskodens tid mellan Standardtid och Sommartid
1. I Världstidfunktionen, tryck D för att visa stadskoden
(tidszonen) som du vill justera Standardtid/Sommartid för.
2. Tryck och håll inne A i ca två sekunder för att växla mellan
Sommartid (DST-indikator visas) och Standardtid (DST-indikator
visas inte).
• När du trycker och håller inne A visas ”Hold” inledningsvis på
displayen. Håll A intryckt tills ”Hold” försvinner.
• DST-indikatorn visas i den nedre displayen när Sommartid är
aktiverad.
• Du kan aktivera DST enskilt för varje stadskod, förutom UTC.
• Om du aktiverar DST för stadskoden som är vald som din
Hemstad kommer DST att aktiveras för den normala tidvisningen.
E-22
Alarm
När ett alarm är aktiverat ger klockan signal på inställd tid. Ett
av alarmen är ett snoozealarm och de andra fyra är dagliga
alarm. Du kan även aktivera en Timsignal som ger två signaler
varje hel timme.
• Snoozealarmets display visas av, medan de andra alarmdis
playerna är numrerade genom . Timsignaldisplayen visas av .
• Alla inställningar i detta avsnitt utförs i Alarmfunktionen som du
aktiverar genom att trycka C (sida E-7).
E-24
4. När en inställning blinkar, Använd D (+) och B (–) för att ändra den.
5. Tryck A för att lämna inställningsfunktionen.
Alarmfunktion
Alarmet ger signal på inställd tid i 10 sekunder, oavsett vilken funktion klockan benner sig
i. Vid val av snoozealarm upprepas alarmet totalt sju gånger var femte minut eller tills du
avaktiverar alarmet (sida E-27).
• Alarm- och Timsignalfunktionerna utgår från den aktuella tiden i din Hemstad som ställts in
i Tidvisningsfunktionen.
• Tryck på valfri knapp för att stoppa alarmsignalen när den har börjat ljuda.
• Om något av följande utförs under pågående 5-minutersintervall avbryts snoozealarmet:
Visa inställningsdisplayen för Tidvisningsfunktionen (sida E-9) Visa inställningsdisplayen
(sida E-25)
Att testa alarmet
I Alarmfunktionen, tryck och håll inne D för att testa alarmet.
E-26
Att aktivera/avaktivera Timsignalen
1. I Alarmfunktionen, använd D för att välja Timsignalen ( )
(sida E-25).
2. Tryck A för att växla mellan ON och OFF.
• Timsignal på-indikatorn visas på displayen i alla funktioner när
Timsignalen är aktiverad.
E-28
Bruksanvisning 5259
Operation Guide 5259
E-20
World Time
World Time digitally displays the current time in one of
48 cities (29 time zones) around the world. A simple
operation swaps your Home City with the currently
selected World Time City.
• The times kept in the World Time Mode are
synchronized with the time being kept in the
Timekeeping Mode. If you feel that there is an error in
any World Time Mode time, check to make sure you
have the correct city selected as your Home City. Also
check to make sure that the current time as shown in
the Timekeeping Mode is correct.
• Times in the World Time Mode are based on UTC
offsets. See the “City Code Table” at the back of this
manual for information about the UTC offsets that are
supported.
• All of the operations in this section are performed in the World Time Mode, which
you enter by pressing C (page E-7).
World Time
Currently selected
World Time City
E-21
▲
A
One second
To view the current time in another time zone
In the World Time Mode, use D to scroll through available city codes (time zones).
Holding down the button scrolls at high speed.
• The lower display shows the current time in the World Time City.
• To select the UTC time zone (Differential 0), press B and D at the same time.
• When the city code (time zone) you want is selected, you can press A to display
the date. After about one second, the watch will resume regular timekeeping for the
currently selected city.
Hour : Minutes
Seconds
Date
E-22
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, press D to display the city
code (time zone) whose Standard Time/Daylight Saving
Time setting you want to change.
2. Hold down A for about two seconds to toggle between
Daylight Saving Time (DST indicator displayed) and
Standard Time ( DST indicator not displayed).
• Holding down A will initially cause “Hold” to appear on
the screen. Keep A depressed until “Hold” disappears.
• The DST indicator is shown in the lower display while
Daylight Saving Time is turned on.
• You can turn on DST individually for each city code,
except UTC.
• Turning on DST for the city code that is currently
selected as your Home City will turn on DST for normal
timekeeping.
DST indicator
E-23
Swapping your Home City and World Time City
You can use the procedure below to swap your Home City and World Time City. This
changes your Home City to your World Time City, and your World Time City to your
Home City. This capability can come in handy when you frequently travel between two
cities in different time zones.
To swap your Home City and World Time City
1. In the World Time Mode, use D to select the World Time City you want.
2. Press A and B at the same time until the watch beeps.
• This will make the World Time City you selected in step 1 your Home City, and cause
the hour and minute hands to move to the current time in that city. At the same time,
it will change the Home City you had selected prior to step 2 your World Time City,
and cause the content of lower display to change accordingly.
• After swapping the Home City and World Time City, the watch stays in the World
Time Mode with the city that was selected as the Home City prior to step 2 now
displayed as the World Time City.
E-24
Alarms
When an alarm is turned on, the alarm tone will sound
when its alarm time is reached. One of the alarms is a
snooze alarm, while the other four are daily alarms.
You also can turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
• The snooze alarm screen is indicated by
, while the
other alarm screens are numbered
through . The
Hourly Time Signal screen is indicated by
.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C (page
E-7).
Alarm time
(Hour : Minutes)
E-25
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
DDDD
DD
• To set an alarm time, display the applicable alarm
screen (
through , or ).
•
is the hourly time signal setting (page E-28).
• The snooze alarm operation repeats every five
minutes.
2. After you select an alarm, hold down A for about two seconds until the hour setting
of the alarm time starts to flash. This is the setting mode.
•
Holding down A will initially cause “Hold” to appear on the screen. Keep A
depressed until “Hold” disappears.
• This operation turns on the alarm automatically.
3. Press C to move the flashing between the hour and minute settings.
OFF
E-26
4. While a setting is flashing, use D (+) and B (–) to change it.
5. Press A to exit the setting mode.
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, or until you turn the alarm off (page E-27).
• Alarm and Hourly Time Signal operations are performed in accordance with the
current time in your Home City, as kept in the Timekeeping Mode.
• To stop the alarm tone after it starts to sound, press any button.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen (page E-9)
Displaying the
setting screen (page E-25)
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
E-27
To turn an alarm on and off
1. In the Alarm Mode, use D to select an alarm.
2. Press A to toggle it on and off.
• Turning on a alarm (
, , , or ) displays
the alarm on indicator on its Alarm Mode screen.
• In all modes, the alarm on indicator is shown for any
alarm that currently is turned on.
• The alarm on indicator flashes while the alarm is
sounding.
• The snooze alarm indicator flashes while the snooze
alarm is sounding and during the 5-minute intervals
between alarms.
Alarm on indicator
Snooze alarm indicator
ON
E-28
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select the Hourly Time
Signal (
) (page E-25).
2. Press A to toggle it on and off.
• The Hourly Time Signal on indicator is shown on the
display in all modes while this function is turned on.
ON
Hourly time signal
on indicator
E-29
Illumination
An LED (light-emitting diode) illuminates the face of the
watch for easy reading in the dark. The watch’s auto light
switch turns on illumination automatically when you angle
the watch towards your face.
• The auto light switch must be turned on (indicated by
the auto light switch indicator) for it to operate.
• See “Illumination Precautions” (page E-38) for other
important information about using illumination.
To illuminate the display manually
In any mode, press B to turn on illumination.
• The above operation turns on illumination regardless of
the current auto light switch setting.
• You can use the procedure below to select either 1.5
seconds or 3 seconds as the illumination duration. When
you press B, the illumination will remain on for about
1.5 seconds or 3 seconds, depending on the current
illumination duration setting.
Auto light switch
indicator
Att visa den aktuella tiden i en annan tidszon
I Världstidfunktionen, använd D för att scrolla genom tillgängliga stadskoder (tidszoner).
Tryck och håll inne knappen för att scrolla med hög hastighet.
• Den nedre displayen visar den aktuella tiden i Världstidsstaden.
• För att välja UTC-tidszonen (Differential 0), tryck B och D samtidigt.
• När den önskade stadskoden (tidszonen) är vald kan du trycka A för att visa datumet.
Efter ca en sekund återgår klockan till den normala tidvisningen för den valda staden.
Växla din Hemstad och Världstidsstad
Med hjälp av anvisningarna nedan kan du växla mellan din Hemstad och Världstidsstad.
Detta ändrar din Hemstad till din Världstidsstad och vice versa. Detta är en praktisk
funktion om du ofta reser mellan två städer i olika tidszoner.
Att växla din Hemstad och Världstidsstad
1. I Världstidfunktionen, använd D för att välja önskad Världstidsstad.
2. Tryck A och B samtidigt tills klockan piper.
• Detta gör Världstidsstaden som du valde i steg 1 till din Hemstad och får tim- och
minutvisarna att ytta sig till den aktuella tiden i den staden. Det ändrar samtidigt
Hemstaden som du hade valt innan steg 2 till din Världstidsstad och justerar den nedre
displayens innehåll därefter.
• När du har växlat Hemstad och Världstidsstad stannar klockan kvar i Världstid-
funktionen, medan staden som hade valts som Hemstad innan steg 2 nu visas som
Världstidsstad.
E-23
Att ställa in en alarmtid
1. I Alarmfunktionen, använd D för att scrolla genom
alarmdisplayerna tills alarmet som du vill ställa in visas.
• För att ställa in en alarmtid, visa den relevanta
alarmdisplayen ( till , eller ).
• är timsignalinställningen (sida E-28).
• Snoozealarmet upprepas var femte minut.
2. När du har valt ett alarm, tryck och håll inne A i ca två sekunder tills alarmtidens
timinställning börjar blinka. Detta är inställningsfunktionen.
• När du trycker och håller inne A visas ”Hold” inledningsvis på displayen. Håll A intryckt
tills ”Hold” försvinner.
• Detta aktiverar alarmet automatiskt.
3. Tryck C för att ytta blinkanket mellan tim- och minutinställningarna.
E-25
Att aktivera/avaktivera ett alarm
1. I Alarmfunktionen, använd D för att välja ett alarm.
2. Tryck A för att växla mellan ON och OFF.
• När ett alarm aktiveras ( , , , eller )
visas Alarm på-indikatorn på Alarmfunktionens display.
• Alarm på-indikatorn visas i alla funktioner för alla alarm som
är aktiverade för tillfället.
• Alarm på-indikatorn blinkar när alarmet ljuder.
• Snoozealarmindikatorn blinkar när snoozealarmet ljuder och
under 5-minutersintervallen mellan alarmen.
E-27
Belysning
Klockan använder LED-belysning (light-emitting-diod) för
lättare avläsning av displayen i mörker. Om den automatiska
belysningsfunktionen är aktiverad, tänds belysningen
automatiskt när klockan vinklas mot ansiktet.
• Den automatiska belysningen måste vara aktiverad (visas
av indikatorn för automatisk belysning) för att fungera.
• Se ”Försiktighetsåtgärder vid användning av
belysningen” (sida E-38) för ytterligare viktig information om
användningen av belysningen.
Att belysa displayen manuellt
I alla funktioner, tryck B för att aktivera belysningen.
• Om du gör enligt ovan aktiveras belysningen oavsett den
aktuella inställningen för automatisk belysning.
• Du kan följa beskrivningen nedan för att välja en belys
ningstid på antingen 1,5 eller 3 sekunder. När du trycker B
förblir belysningen på i ca 1,5 eller 3 sekunder, beroende på
den aktuella inställningen för belysningstiden.
Indikator för automatisk belysning
E-29
Operation Guide 5259
E-20
World Time
World Time digitally displays the current time in one of
48 cities (29 time zones) around the world. A simple
operation swaps your Home City with the currently
selected World Time City.
• The times kept in the World Time Mode are
synchronized with the time being kept in the
Timekeeping Mode. If you feel that there is an error in
any World Time Mode time, check to make sure you
have the correct city selected as your Home City. Also
check to make sure that the current time as shown in
the Timekeeping Mode is correct.
• Times in the World Time Mode are based on UTC
offsets. See the “City Code Table” at the back of this
manual for information about the UTC offsets that are
supported.
• All of the operations in this section are performed in the World Time Mode, which
you enter by pressing C (page E-7).
World Time
Currently selected
World Time City
E-21
▲
A
One second
To view the current time in another time zone
In the World Time Mode, use D to scroll through available city codes (time zones).
Holding down the button scrolls at high speed.
• The lower display shows the current time in the World Time City.
• To select the UTC time zone (Differential 0), press B and D at the same time.
• When the city code (time zone) you want is selected, you can press A to display
the date. After about one second, the watch will resume regular timekeeping for the
currently selected city.
Hour : Minutes
Seconds
Date
E-22
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, press D to display the city
code (time zone) whose Standard Time/Daylight Saving
Time setting you want to change.
2. Hold down A for about two seconds to toggle between
Daylight Saving Time (DST indicator displayed) and
Standard Time ( DST indicator not displayed).
• Holding down A will initially cause “Hold” to appear on
the screen. Keep A depressed until “Hold” disappears.
• The DST indicator is shown in the lower display while
Daylight Saving Time is turned on.
• You can turn on DST individually for each city code,
except UTC.
• Turning on DST for the city code that is currently
selected as your Home City will turn on DST for normal
timekeeping.
DST indicator
E-23
Swapping your Home City and World Time City
You can use the procedure below to swap your Home City and World Time City. This
changes your Home City to your World Time City, and your World Time City to your
Home City. This capability can come in handy when you frequently travel between two
cities in different time zones.
To swap your Home City and World Time City
1. In the World Time Mode, use D to select the World Time City you want.
2. Press A and B at the same time until the watch beeps.
• This will make the World Time City you selected in step 1 your Home City, and cause
the hour and minute hands to move to the current time in that city. At the same time,
it will change the Home City you had selected prior to step 2 your World Time City,
and cause the content of lower display to change accordingly.
• After swapping the Home City and World Time City, the watch stays in the World
Time Mode with the city that was selected as the Home City prior to step 2 now
displayed as the World Time City.
E-24
Alarms
When an alarm is turned on, the alarm tone will sound
when its alarm time is reached. One of the alarms is a
snooze alarm, while the other four are daily alarms.
You also can turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
• The snooze alarm screen is indicated by
, while the
other alarm screens are numbered
through . The
Hourly Time Signal screen is indicated by
.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C (page
E-7).
Alarm time
(Hour : Minutes)
E-25
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
DDDD
DD
• To set an alarm time, display the applicable alarm
screen (
through , or ).
•
is the hourly time signal setting (page E-28).
• The snooze alarm operation repeats every five
minutes.
2. After you select an alarm, hold down A for about two seconds until the hour setting
of the alarm time starts to flash. This is the setting mode.
•
Holding down A will initially cause “Hold” to appear on the screen. Keep A
depressed until “Hold” disappears.
• This operation turns on the alarm automatically.
3. Press C to move the flashing between the hour and minute settings.
OFF
E-26
4. While a setting is flashing, use D (+) and B (–) to change it.
5. Press A to exit the setting mode.
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, or until you turn the alarm off (page E-27).
• Alarm and Hourly Time Signal operations are performed in accordance with the
current time in your Home City, as kept in the Timekeeping Mode.
• To stop the alarm tone after it starts to sound, press any button.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen (page E-9)
Displaying the
setting screen (page E-25)
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
E-27
To turn an alarm on and off
1. In the Alarm Mode, use D to select an alarm.
2. Press A to toggle it on and off.
• Turning on a alarm (
, , , or ) displays
the alarm on indicator on its Alarm Mode screen.
• In all modes, the alarm on indicator is shown for any
alarm that currently is turned on.
• The alarm on indicator flashes while the alarm is
sounding.
• The snooze alarm indicator flashes while the snooze
alarm is sounding and during the 5-minute intervals
between alarms.
Alarm on indicator
Snooze alarm indicator
ON
E-28
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select the Hourly Time
Signal (
) (page E-25).
2. Press A to toggle it on and off.
• The Hourly Time Signal on indicator is shown on the
display in all modes while this function is turned on.
ON
Hourly time signal
on indicator
E-29
Illumination
An LED (light-emitting diode) illuminates the face of the
watch for easy reading in the dark. The watch’s auto light
switch turns on illumination automatically when you angle
the watch towards your face.
• The auto light switch must be turned on (indicated by
the auto light switch indicator) for it to operate.
• See “Illumination Precautions” (page E-38) for other
important information about using illumination.
To illuminate the display manually
In any mode, press B to turn on illumination.
• The above operation turns on illumination regardless of
the current auto light switch setting.
• You can use the procedure below to select either 1.5
seconds or 3 seconds as the illumination duration. When
you press B, the illumination will remain on for about
1.5 seconds or 3 seconds, depending on the current
illumination duration setting.
Auto light switch
indicator
Operation Guide 5259
E-20
World Time
World Time digitally displays the current time in one of
48 cities (29 time zones) around the world. A simple
operation swaps your Home City with the currently
selected World Time City.
• The times kept in the World Time Mode are
synchronized with the time being kept in the
Timekeeping Mode. If you feel that there is an error in
any World Time Mode time, check to make sure you
have the correct city selected as your Home City. Also
check to make sure that the current time as shown in
the Timekeeping Mode is correct.
• Times in the World Time Mode are based on UTC
offsets. See the “City Code Table” at the back of this
manual for information about the UTC offsets that are
supported.
• All of the operations in this section are performed in the World Time Mode, which
you enter by pressing C (page E-7).
World Time
Currently selected
World Time City
E-21
▲
A
One second
To view the current time in another time zone
In the World Time Mode, use D to scroll through available city codes (time zones).
Holding down the button scrolls at high speed.
• The lower display shows the current time in the World Time City.
• To select the UTC time zone (Differential 0), press B and D at the same time.
• When the city code (time zone) you want is selected, you can press A to display
the date. After about one second, the watch will resume regular timekeeping for the
currently selected city.
Hour : Minutes
Seconds
Date
E-22
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, press D to display the city
code (time zone) whose Standard Time/Daylight Saving
Time setting you want to change.
2. Hold down A for about two seconds to toggle between
Daylight Saving Time (DST indicator displayed) and
Standard Time ( DST indicator not displayed).
• Holding down A will initially cause “Hold” to appear on
the screen. Keep A depressed until “Hold” disappears.
• The DST indicator is shown in the lower display while
Daylight Saving Time is turned on.
• You can turn on DST individually for each city code,
except UTC.
• Turning on DST for the city code that is currently
selected as your Home City will turn on DST for normal
timekeeping.
DST indicator
E-23
Swapping your Home City and World Time City
You can use the procedure below to swap your Home City and World Time City. This
changes your Home City to your World Time City, and your World Time City to your
Home City. This capability can come in handy when you frequently travel between two
cities in different time zones.
To swap your Home City and World Time City
1. In the World Time Mode, use D to select the World Time City you want.
2. Press A and B at the same time until the watch beeps.
• This will make the World Time City you selected in step 1 your Home City, and cause
the hour and minute hands to move to the current time in that city. At the same time,
it will change the Home City you had selected prior to step 2 your World Time City,
and cause the content of lower display to change accordingly.
• After swapping the Home City and World Time City, the watch stays in the World
Time Mode with the city that was selected as the Home City prior to step 2 now
displayed as the World Time City.
E-24
Alarms
When an alarm is turned on, the alarm tone will sound
when its alarm time is reached. One of the alarms is a
snooze alarm, while the other four are daily alarms.
You also can turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
• The snooze alarm screen is indicated by
, while the
other alarm screens are numbered
through . The
Hourly Time Signal screen is indicated by
.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C (page
E-7).
Alarm time
(Hour : Minutes)
E-25
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
DDDD
DD
• To set an alarm time, display the applicable alarm
screen (
through , or ).
•
is the hourly time signal setting (page E-28).
• The snooze alarm operation repeats every five
minutes.
2. After you select an alarm, hold down A for about two seconds until the hour setting
of the alarm time starts to flash. This is the setting mode.
•
Holding down A will initially cause “Hold” to appear on the screen. Keep A
depressed until “Hold” disappears.
• This operation turns on the alarm automatically.
3. Press C to move the flashing between the hour and minute settings.
OFF
E-26
4. While a setting is flashing, use D (+) and B (–) to change it.
5. Press A to exit the setting mode.
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, or until you turn the alarm off (page E-27).
• Alarm and Hourly Time Signal operations are performed in accordance with the
current time in your Home City, as kept in the Timekeeping Mode.
• To stop the alarm tone after it starts to sound, press any button.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen (page E-9)
Displaying the
setting screen (page E-25)
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
E-27
To turn an alarm on and off
1. In the Alarm Mode, use D to select an alarm.
2. Press A to toggle it on and off.
• Turning on a alarm (
, , , or ) displays
the alarm on indicator on its Alarm Mode screen.
• In all modes, the alarm on indicator is shown for any
alarm that currently is turned on.
• The alarm on indicator flashes while the alarm is
sounding.
• The snooze alarm indicator flashes while the snooze
alarm is sounding and during the 5-minute intervals
between alarms.
Alarm on indicator
Snooze alarm indicator
ON
E-28
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select the Hourly Time
Signal (
) (page E-25).
2. Press A to toggle it on and off.
• The Hourly Time Signal on indicator is shown on the
display in all modes while this function is turned on.
ON
Hourly time signal
on indicator
E-29
Illumination
An LED (light-emitting diode) illuminates the face of the
watch for easy reading in the dark. The watch’s auto light
switch turns on illumination automatically when you angle
the watch towards your face.
• The auto light switch must be turned on (indicated by
the auto light switch indicator) for it to operate.
• See “Illumination Precautions” (page E-38) for other
important information about using illumination.
To illuminate the display manually
In any mode, press B to turn on illumination.
• The above operation turns on illumination regardless of
the current auto light switch setting.
• You can use the procedure below to select either 1.5
seconds or 3 seconds as the illumination duration. When
you press B, the illumination will remain on for about
1.5 seconds or 3 seconds, depending on the current
illumination duration setting.
Auto light switch
indicator
Operation Guide 5259
E-20
World Time
World Time digitally displays the current time in one of
48 cities (29 time zones) around the world. A simple
operation swaps your Home City with the currently
selected World Time City.
• The times kept in the World Time Mode are
synchronized with the time being kept in the
Timekeeping Mode. If you feel that there is an error in
any World Time Mode time, check to make sure you
have the correct city selected as your Home City. Also
check to make sure that the current time as shown in
the Timekeeping Mode is correct.
• Times in the World Time Mode are based on UTC
offsets. See the “City Code Table” at the back of this
manual for information about the UTC offsets that are
supported.
• All of the operations in this section are performed in the World Time Mode, which
you enter by pressing C (page E-7).
World Time
Currently selected
World Time City
E-21
▲
A
One second
To view the current time in another time zone
In the World Time Mode, use D to scroll through available city codes (time zones).
Holding down the button scrolls at high speed.
• The lower display shows the current time in the World Time City.
• To select the UTC time zone (Differential 0), press B and D at the same time.
• When the city code (time zone) you want is selected, you can press A to display
the date. After about one second, the watch will resume regular timekeeping for the
currently selected city.
Hour : Minutes
Seconds
Date
E-22
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, press D to display the city
code (time zone) whose Standard Time/Daylight Saving
Time setting you want to change.
2. Hold down A for about two seconds to toggle between
Daylight Saving Time (DST indicator displayed) and
Standard Time ( DST indicator not displayed).
• Holding down A will initially cause “Hold” to appear on
the screen. Keep A depressed until “Hold” disappears.
• The DST indicator is shown in the lower display while
Daylight Saving Time is turned on.
• You can turn on DST individually for each city code,
except UTC.
• Turning on DST for the city code that is currently
selected as your Home City will turn on DST for normal
timekeeping.
DST indicator
E-23
Swapping your Home City and World Time City
You can use the procedure below to swap your Home City and World Time City. This
changes your Home City to your World Time City, and your World Time City to your
Home City. This capability can come in handy when you frequently travel between two
cities in different time zones.
To swap your Home City and World Time City
1. In the World Time Mode, use D to select the World Time City you want.
2. Press A and B at the same time until the watch beeps.
• This will make the World Time City you selected in step 1 your Home City, and cause
the hour and minute hands to move to the current time in that city. At the same time,
it will change the Home City you had selected prior to step 2 your World Time City,
and cause the content of lower display to change accordingly.
• After swapping the Home City and World Time City, the watch stays in the World
Time Mode with the city that was selected as the Home City prior to step 2 now
displayed as the World Time City.
E-24
Alarms
When an alarm is turned on, the alarm tone will sound
when its alarm time is reached. One of the alarms is a
snooze alarm, while the other four are daily alarms.
You also can turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
• The snooze alarm screen is indicated by
, while the
other alarm screens are numbered
through . The
Hourly Time Signal screen is indicated by
.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C (page
E-7).
Alarm time
(Hour : Minutes)
E-25
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
DDDD
DD
• To set an alarm time, display the applicable alarm
screen (
through , or ).
•
is the hourly time signal setting (page E-28).
• The snooze alarm operation repeats every five
minutes.
2. After you select an alarm, hold down A for about two seconds until the hour setting
of the alarm time starts to flash. This is the setting mode.
•
Holding down A will initially cause “Hold” to appear on the screen. Keep A
depressed until “Hold” disappears.
• This operation turns on the alarm automatically.
3. Press C to move the flashing between the hour and minute settings.
OFF
E-26
4. While a setting is flashing, use D (+) and B (–) to change it.
5. Press A to exit the setting mode.
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, or until you turn the alarm off (page E-27).
• Alarm and Hourly Time Signal operations are performed in accordance with the
current time in your Home City, as kept in the Timekeeping Mode.
• To stop the alarm tone after it starts to sound, press any button.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen (page E-9)
Displaying the
setting screen (page E-25)
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
E-27
To turn an alarm on and off
1. In the Alarm Mode, use D to select an alarm.
2. Press A to toggle it on and off.
• Turning on a alarm (
, , , or ) displays
the alarm on indicator on its Alarm Mode screen.
• In all modes, the alarm on indicator is shown for any
alarm that currently is turned on.
• The alarm on indicator flashes while the alarm is
sounding.
• The snooze alarm indicator flashes while the snooze
alarm is sounding and during the 5-minute intervals
between alarms.
Alarm on indicator
Snooze alarm indicator
ON
E-28
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select the Hourly Time
Signal (
) (page E-25).
2. Press A to toggle it on and off.
• The Hourly Time Signal on indicator is shown on the
display in all modes while this function is turned on.
ON
Hourly time signal
on indicator
E-29
Illumination
An LED (light-emitting diode) illuminates the face of the
watch for easy reading in the dark. The watch’s auto light
switch turns on illumination automatically when you angle
the watch towards your face.
• The auto light switch must be turned on (indicated by
the auto light switch indicator) for it to operate.
• See “Illumination Precautions” (page E-38) for other
important information about using illumination.
To illuminate the display manually
In any mode, press B to turn on illumination.
• The above operation turns on illumination regardless of
the current auto light switch setting.
• You can use the procedure below to select either 1.5
seconds or 3 seconds as the illumination duration. When
you press B, the illumination will remain on for about
1.5 seconds or 3 seconds, depending on the current
illumination duration setting.
Auto light switch
indicator
Operation Guide 5259
E-20
World Time
World Time digitally displays the current time in one of
48 cities (29 time zones) around the world. A simple
operation swaps your Home City with the currently
selected World Time City.
• The times kept in the World Time Mode are
synchronized with the time being kept in the
Timekeeping Mode. If you feel that there is an error in
any World Time Mode time, check to make sure you
have the correct city selected as your Home City. Also
check to make sure that the current time as shown in
the Timekeeping Mode is correct.
• Times in the World Time Mode are based on UTC
offsets. See the “City Code Table” at the back of this
manual for information about the UTC offsets that are
supported.
• All of the operations in this section are performed in the World Time Mode, which
you enter by pressing C (page E-7).
World Time
Currently selected
World Time City
E-21
▲
A
One second
To view the current time in another time zone
In the World Time Mode, use D to scroll through available city codes (time zones).
Holding down the button scrolls at high speed.
• The lower display shows the current time in the World Time City.
• To select the UTC time zone (Differential 0), press B and D at the same time.
• When the city code (time zone) you want is selected, you can press A to display
the date. After about one second, the watch will resume regular timekeeping for the
currently selected city.
Hour : Minutes
Seconds
Date
E-22
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, press D to display the city
code (time zone) whose Standard Time/Daylight Saving
Time setting you want to change.
2. Hold down A for about two seconds to toggle between
Daylight Saving Time (DST indicator displayed) and
Standard Time ( DST indicator not displayed).
• Holding down A will initially cause “Hold” to appear on
the screen. Keep A depressed until “Hold” disappears.
• The DST indicator is shown in the lower display while
Daylight Saving Time is turned on.
• You can turn on DST individually for each city code,
except UTC.
• Turning on DST for the city code that is currently
selected as your Home City will turn on DST for normal
timekeeping.
DST indicator
E-23
Swapping your Home City and World Time City
You can use the procedure below to swap your Home City and World Time City. This
changes your Home City to your World Time City, and your World Time City to your
Home City. This capability can come in handy when you frequently travel between two
cities in different time zones.
To swap your Home City and World Time City
1. In the World Time Mode, use D to select the World Time City you want.
2. Press A and B at the same time until the watch beeps.
• This will make the World Time City you selected in step 1 your Home City, and cause
the hour and minute hands to move to the current time in that city. At the same time,
it will change the Home City you had selected prior to step 2 your World Time City,
and cause the content of lower display to change accordingly.
• After swapping the Home City and World Time City, the watch stays in the World
Time Mode with the city that was selected as the Home City prior to step 2 now
displayed as the World Time City.
E-24
Alarms
When an alarm is turned on, the alarm tone will sound
when its alarm time is reached. One of the alarms is a
snooze alarm, while the other four are daily alarms.
You also can turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
• The snooze alarm screen is indicated by
, while the
other alarm screens are numbered
through . The
Hourly Time Signal screen is indicated by
.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C (page
E-7).
Alarm time
(Hour : Minutes)
E-25
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
DDDD
DD
• To set an alarm time, display the applicable alarm
screen (
through , or ).
•
is the hourly time signal setting (page E-28).
• The snooze alarm operation repeats every five
minutes.
2. After you select an alarm, hold down A for about two seconds until the hour setting
of the alarm time starts to flash. This is the setting mode.
•
Holding down A will initially cause “Hold” to appear on the screen. Keep A
depressed until “Hold” disappears.
• This operation turns on the alarm automatically.
3. Press C to move the flashing between the hour and minute settings.
OFF
E-26
4. While a setting is flashing, use D (+) and B (–) to change it.
5. Press A to exit the setting mode.
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, or until you turn the alarm off (page E-27).
• Alarm and Hourly Time Signal operations are performed in accordance with the
current time in your Home City, as kept in the Timekeeping Mode.
• To stop the alarm tone after it starts to sound, press any button.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen (page E-9)
Displaying the
setting screen (page E-25)
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
E-27
To turn an alarm on and off
1. In the Alarm Mode, use D to select an alarm.
2. Press A to toggle it on and off.
• Turning on a alarm (
, , , or ) displays
the alarm on indicator on its Alarm Mode screen.
• In all modes, the alarm on indicator is shown for any
alarm that currently is turned on.
• The alarm on indicator flashes while the alarm is
sounding.
• The snooze alarm indicator flashes while the snooze
alarm is sounding and during the 5-minute intervals
between alarms.
Alarm on indicator
Snooze alarm indicator
ON
E-28
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select the Hourly Time
Signal (
) (page E-25).
2. Press A to toggle it on and off.
• The Hourly Time Signal on indicator is shown on the
display in all modes while this function is turned on.
ON
Hourly time signal
on indicator
E-29
Illumination
An LED (light-emitting diode) illuminates the face of the
watch for easy reading in the dark. The watch’s auto light
switch turns on illumination automatically when you angle
the watch towards your face.
• The auto light switch must be turned on (indicated by
the auto light switch indicator) for it to operate.
• See “Illumination Precautions” (page E-38) for other
important information about using illumination.
To illuminate the display manually
In any mode, press B to turn on illumination.
• The above operation turns on illumination regardless of
the current auto light switch setting.
• You can use the procedure below to select either 1.5
seconds or 3 seconds as the illumination duration. When
you press B, the illumination will remain on for about
1.5 seconds or 3 seconds, depending on the current
illumination duration setting.
Auto light switch
indicator
Operation Guide 5259
E-20
World Time
World Time digitally displays the current time in one of
48 cities (29 time zones) around the world. A simple
operation swaps your Home City with the currently
selected World Time City.
• The times kept in the World Time Mode are
synchronized with the time being kept in the
Timekeeping Mode. If you feel that there is an error in
any World Time Mode time, check to make sure you
have the correct city selected as your Home City. Also
check to make sure that the current time as shown in
the Timekeeping Mode is correct.
• Times in the World Time Mode are based on UTC
offsets. See the “City Code Table” at the back of this
manual for information about the UTC offsets that are
supported.
• All of the operations in this section are performed in the World Time Mode, which
you enter by pressing C (page E-7).
World Time
Currently selected
World Time City
E-21
▲
A
One second
To view the current time in another time zone
In the World Time Mode, use D to scroll through available city codes (time zones).
Holding down the button scrolls at high speed.
• The lower display shows the current time in the World Time City.
• To select the UTC time zone (Differential 0), press B and D at the same time.
• When the city code (time zone) you want is selected, you can press A to display
the date. After about one second, the watch will resume regular timekeeping for the
currently selected city.
Hour : Minutes
Seconds
Date
E-22
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, press D to display the city
code (time zone) whose Standard Time/Daylight Saving
Time setting you want to change.
2. Hold down A for about two seconds to toggle between
Daylight Saving Time (DST indicator displayed) and
Standard Time ( DST indicator not displayed).
• Holding down A will initially cause “Hold” to appear on
the screen. Keep A depressed until “Hold” disappears.
• The DST indicator is shown in the lower display while
Daylight Saving Time is turned on.
• You can turn on DST individually for each city code,
except UTC.
• Turning on DST for the city code that is currently
selected as your Home City will turn on DST for normal
timekeeping.
DST indicator
E-23
Swapping your Home City and World Time City
You can use the procedure below to swap your Home City and World Time City. This
changes your Home City to your World Time City, and your World Time City to your
Home City. This capability can come in handy when you frequently travel between two
cities in different time zones.
To swap your Home City and World Time City
1. In the World Time Mode, use D to select the World Time City you want.
2. Press A and B at the same time until the watch beeps.
• This will make the World Time City you selected in step 1 your Home City, and cause
the hour and minute hands to move to the current time in that city. At the same time,
it will change the Home City you had selected prior to step 2 your World Time City,
and cause the content of lower display to change accordingly.
• After swapping the Home City and World Time City, the watch stays in the World
Time Mode with the city that was selected as the Home City prior to step 2 now
displayed as the World Time City.
E-24
Alarms
When an alarm is turned on, the alarm tone will sound
when its alarm time is reached. One of the alarms is a
snooze alarm, while the other four are daily alarms.
You also can turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
• The snooze alarm screen is indicated by
, while the
other alarm screens are numbered
through . The
Hourly Time Signal screen is indicated by
.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C (page
E-7).
Alarm time
(Hour : Minutes)
E-25
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
DDDD
DD
• To set an alarm time, display the applicable alarm
screen (
through , or ).
•
is the hourly time signal setting (page E-28).
• The snooze alarm operation repeats every five
minutes.
2. After you select an alarm, hold down A for about two seconds until the hour setting
of the alarm time starts to flash. This is the setting mode.
•
Holding down A will initially cause “Hold” to appear on the screen. Keep A
depressed until “Hold” disappears.
• This operation turns on the alarm automatically.
3. Press C to move the flashing between the hour and minute settings.
OFF
E-26
4. While a setting is flashing, use D (+) and B (–) to change it.
5. Press A to exit the setting mode.
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, or until you turn the alarm off (page E-27).
• Alarm and Hourly Time Signal operations are performed in accordance with the
current time in your Home City, as kept in the Timekeeping Mode.
• To stop the alarm tone after it starts to sound, press any button.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen (page E-9)
Displaying the
setting screen (page E-25)
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
E-27
To turn an alarm on and off
1. In the Alarm Mode, use D to select an alarm.
2. Press A to toggle it on and off.
• Turning on a alarm (
, , , or ) displays
the alarm on indicator on its Alarm Mode screen.
• In all modes, the alarm on indicator is shown for any
alarm that currently is turned on.
• The alarm on indicator flashes while the alarm is
sounding.
• The snooze alarm indicator flashes while the snooze
alarm is sounding and during the 5-minute intervals
between alarms.
Alarm on indicator
Snooze alarm indicator
ON
E-28
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select the Hourly Time
Signal (
) (page E-25).
2. Press A to toggle it on and off.
• The Hourly Time Signal on indicator is shown on the
display in all modes while this function is turned on.
ON
Hourly time signal
on indicator
E-29
Illumination
An LED (light-emitting diode) illuminates the face of the
watch for easy reading in the dark. The watch’s auto light
switch turns on illumination automatically when you angle
the watch towards your face.
• The auto light switch must be turned on (indicated by
the auto light switch indicator) for it to operate.
• See “Illumination Precautions” (page E-38) for other
important information about using illumination.
To illuminate the display manually
In any mode, press B to turn on illumination.
• The above operation turns on illumination regardless of
the current auto light switch setting.
• You can use the procedure below to select either 1.5
seconds or 3 seconds as the illumination duration. When
you press B, the illumination will remain on for about
1.5 seconds or 3 seconds, depending on the current
illumination duration setting.
Auto light switch
indicator
Operation Guide 5259
E-20
World Time
World Time digitally displays the current time in one of
48 cities (29 time zones) around the world. A simple
operation swaps your Home City with the currently
selected World Time City.
• The times kept in the World Time Mode are
synchronized with the time being kept in the
Timekeeping Mode. If you feel that there is an error in
any World Time Mode time, check to make sure you
have the correct city selected as your Home City. Also
check to make sure that the current time as shown in
the Timekeeping Mode is correct.
• Times in the World Time Mode are based on UTC
offsets. See the “City Code Table” at the back of this
manual for information about the UTC offsets that are
supported.
• All of the operations in this section are performed in the World Time Mode, which
you enter by pressing C (page E-7).
World Time
Currently selected
World Time City
E-21
▲
A
One second
To view the current time in another time zone
In the World Time Mode, use D to scroll through available city codes (time zones).
Holding down the button scrolls at high speed.
• The lower display shows the current time in the World Time City.
• To select the UTC time zone (Differential 0), press B and D at the same time.
• When the city code (time zone) you want is selected, you can press A to display
the date. After about one second, the watch will resume regular timekeeping for the
currently selected city.
Hour : Minutes
Seconds
Date
E-22
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, press D to display the city
code (time zone) whose Standard Time/Daylight Saving
Time setting you want to change.
2. Hold down A for about two seconds to toggle between
Daylight Saving Time (DST indicator displayed) and
Standard Time ( DST indicator not displayed).
• Holding down A will initially cause “Hold” to appear on
the screen. Keep A depressed until “Hold” disappears.
• The DST indicator is shown in the lower display while
Daylight Saving Time is turned on.
• You can turn on DST individually for each city code,
except UTC.
• Turning on DST for the city code that is currently
selected as your Home City will turn on DST for normal
timekeeping.
DST indicator
E-23
Swapping your Home City and World Time City
You can use the procedure below to swap your Home City and World Time City. This
changes your Home City to your World Time City, and your World Time City to your
Home City. This capability can come in handy when you frequently travel between two
cities in different time zones.
To swap your Home City and World Time City
1. In the World Time Mode, use D to select the World Time City you want.
2. Press A and B at the same time until the watch beeps.
• This will make the World Time City you selected in step 1 your Home City, and cause
the hour and minute hands to move to the current time in that city. At the same time,
it will change the Home City you had selected prior to step 2 your World Time City,
and cause the content of lower display to change accordingly.
• After swapping the Home City and World Time City, the watch stays in the World
Time Mode with the city that was selected as the Home City prior to step 2 now
displayed as the World Time City.
E-24
Alarms
When an alarm is turned on, the alarm tone will sound
when its alarm time is reached. One of the alarms is a
snooze alarm, while the other four are daily alarms.
You also can turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
• The snooze alarm screen is indicated by
, while the
other alarm screens are numbered
through . The
Hourly Time Signal screen is indicated by
.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C (page
E-7).
Alarm time
(Hour : Minutes)
E-25
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
DDDD
DD
• To set an alarm time, display the applicable alarm
screen (
through , or ).
•
is the hourly time signal setting (page E-28).
• The snooze alarm operation repeats every five
minutes.
2. After you select an alarm, hold down A for about two seconds until the hour setting
of the alarm time starts to flash. This is the setting mode.
•
Holding down A will initially cause “Hold” to appear on the screen. Keep A
depressed until “Hold” disappears.
• This operation turns on the alarm automatically.
3. Press C to move the flashing between the hour and minute settings.
OFF
E-26
4. While a setting is flashing, use D (+) and B (–) to change it.
5. Press A to exit the setting mode.
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, or until you turn the alarm off (page E-27).
• Alarm and Hourly Time Signal operations are performed in accordance with the
current time in your Home City, as kept in the Timekeeping Mode.
• To stop the alarm tone after it starts to sound, press any button.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen (page E-9)
Displaying the
setting screen (page E-25)
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
E-27
To turn an alarm on and off
1. In the Alarm Mode, use D to select an alarm.
2. Press A to toggle it on and off.
• Turning on a alarm (
, , , or ) displays
the alarm on indicator on its Alarm Mode screen.
• In all modes, the alarm on indicator is shown for any
alarm that currently is turned on.
• The alarm on indicator flashes while the alarm is
sounding.
• The snooze alarm indicator flashes while the snooze
alarm is sounding and during the 5-minute intervals
between alarms.
Alarm on indicator
Snooze alarm indicator
ON
E-28
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select the Hourly Time
Signal (
) (page E-25).
2. Press A to toggle it on and off.
• The Hourly Time Signal on indicator is shown on the
display in all modes while this function is turned on.
ON
Hourly time signal
on indicator
E-29
Illumination
An LED (light-emitting diode) illuminates the face of the
watch for easy reading in the dark. The watch’s auto light
switch turns on illumination automatically when you angle
the watch towards your face.
• The auto light switch must be turned on (indicated by
the auto light switch indicator) for it to operate.
• See “Illumination Precautions” (page E-38) for other
important information about using illumination.
To illuminate the display manually
In any mode, press B to turn on illumination.
• The above operation turns on illumination regardless of
the current auto light switch setting.
• You can use the procedure below to select either 1.5
seconds or 3 seconds as the illumination duration. When
you press B, the illumination will remain on for about
1.5 seconds or 3 seconds, depending on the current
illumination duration setting.
Auto light switch
indicator
Operation Guide 5259
E-20
World Time
World Time digitally displays the current time in one of
48 cities (29 time zones) around the world. A simple
operation swaps your Home City with the currently
selected World Time City.
• The times kept in the World Time Mode are
synchronized with the time being kept in the
Timekeeping Mode. If you feel that there is an error in
any World Time Mode time, check to make sure you
have the correct city selected as your Home City. Also
check to make sure that the current time as shown in
the Timekeeping Mode is correct.
• Times in the World Time Mode are based on UTC
offsets. See the “City Code Table” at the back of this
manual for information about the UTC offsets that are
supported.
• All of the operations in this section are performed in the World Time Mode, which
you enter by pressing C (page E-7).
World Time
Currently selected
World Time City
E-21
▲
A
One second
To view the current time in another time zone
In the World Time Mode, use D to scroll through available city codes (time zones).
Holding down the button scrolls at high speed.
• The lower display shows the current time in the World Time City.
• To select the UTC time zone (Differential 0), press B and D at the same time.
• When the city code (time zone) you want is selected, you can press A to display
the date. After about one second, the watch will resume regular timekeeping for the
currently selected city.
Hour : Minutes
Seconds
Date
E-22
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, press D to display the city
code (time zone) whose Standard Time/Daylight Saving
Time setting you want to change.
2. Hold down A for about two seconds to toggle between
Daylight Saving Time (DST indicator displayed) and
Standard Time ( DST indicator not displayed).
• Holding down A will initially cause “Hold” to appear on
the screen. Keep A depressed until “Hold” disappears.
• The DST indicator is shown in the lower display while
Daylight Saving Time is turned on.
• You can turn on DST individually for each city code,
except UTC.
• Turning on DST for the city code that is currently
selected as your Home City will turn on DST for normal
timekeeping.
DST indicator
E-23
Swapping your Home City and World Time City
You can use the procedure below to swap your Home City and World Time City. This
changes your Home City to your World Time City, and your World Time City to your
Home City. This capability can come in handy when you frequently travel between two
cities in different time zones.
To swap your Home City and World Time City
1. In the World Time Mode, use D to select the World Time City you want.
2. Press A and B at the same time until the watch beeps.
• This will make the World Time City you selected in step 1 your Home City, and cause
the hour and minute hands to move to the current time in that city. At the same time,
it will change the Home City you had selected prior to step 2 your World Time City,
and cause the content of lower display to change accordingly.
• After swapping the Home City and World Time City, the watch stays in the World
Time Mode with the city that was selected as the Home City prior to step 2 now
displayed as the World Time City.
E-24
Alarms
When an alarm is turned on, the alarm tone will sound
when its alarm time is reached. One of the alarms is a
snooze alarm, while the other four are daily alarms.
You also can turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
• The snooze alarm screen is indicated by
, while the
other alarm screens are numbered
through . The
Hourly Time Signal screen is indicated by
.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C (page
E-7).
Alarm time
(Hour : Minutes)
E-25
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
DDDD
DD
• To set an alarm time, display the applicable alarm
screen (
through , or ).
•
is the hourly time signal setting (page E-28).
• The snooze alarm operation repeats every five
minutes.
2. After you select an alarm, hold down A for about two seconds until the hour setting
of the alarm time starts to flash. This is the setting mode.
•
Holding down A will initially cause “Hold” to appear on the screen. Keep A
depressed until “Hold” disappears.
• This operation turns on the alarm automatically.
3. Press C to move the flashing between the hour and minute settings.
OFF
E-26
4. While a setting is flashing, use D (+) and B (–) to change it.
5. Press A to exit the setting mode.
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, or until you turn the alarm off (page E-27).
• Alarm and Hourly Time Signal operations are performed in accordance with the
current time in your Home City, as kept in the Timekeeping Mode.
• To stop the alarm tone after it starts to sound, press any button.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen (page E-9)
Displaying the
setting screen (page E-25)
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
E-27
To turn an alarm on and off
1. In the Alarm Mode, use D to select an alarm.
2. Press A to toggle it on and off.
• Turning on a alarm (
, , , or ) displays
the alarm on indicator on its Alarm Mode screen.
• In all modes, the alarm on indicator is shown for any
alarm that currently is turned on.
• The alarm on indicator flashes while the alarm is
sounding.
• The snooze alarm indicator flashes while the snooze
alarm is sounding and during the 5-minute intervals
between alarms.
Alarm on indicator
Snooze alarm indicator
ON
E-28
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select the Hourly Time
Signal (
) (page E-25).
2. Press A to toggle it on and off.
• The Hourly Time Signal on indicator is shown on the
display in all modes while this function is turned on.
ON
Hourly time signal
on indicator
E-29
Illumination
An LED (light-emitting diode) illuminates the face of the
watch for easy reading in the dark. The watch’s auto light
switch turns on illumination automatically when you angle
the watch towards your face.
• The auto light switch must be turned on (indicated by
the auto light switch indicator) for it to operate.
• See “Illumination Precautions” (page E-38) for other
important information about using illumination.
To illuminate the display manually
In any mode, press B to turn on illumination.
• The above operation turns on illumination regardless of
the current auto light switch setting.
• You can use the procedure below to select either 1.5
seconds or 3 seconds as the illumination duration. When
you press B, the illumination will remain on for about
1.5 seconds or 3 seconds, depending on the current
illumination duration setting.
Auto light switch
indicator
Operation Guide 5259
E-20
World Time
World Time digitally displays the current time in one of
48 cities (29 time zones) around the world. A simple
operation swaps your Home City with the currently
selected World Time City.
• The times kept in the World Time Mode are
synchronized with the time being kept in the
Timekeeping Mode. If you feel that there is an error in
any World Time Mode time, check to make sure you
have the correct city selected as your Home City. Also
check to make sure that the current time as shown in
the Timekeeping Mode is correct.
• Times in the World Time Mode are based on UTC
offsets. See the “City Code Table” at the back of this
manual for information about the UTC offsets that are
supported.
• All of the operations in this section are performed in the World Time Mode, which
you enter by pressing C (page E-7).
World Time
Currently selected
World Time City
E-21
▲
A
One second
To view the current time in another time zone
In the World Time Mode, use D to scroll through available city codes (time zones).
Holding down the button scrolls at high speed.
• The lower display shows the current time in the World Time City.
• To select the UTC time zone (Differential 0), press B and D at the same time.
• When the city code (time zone) you want is selected, you can press A to display
the date. After about one second, the watch will resume regular timekeeping for the
currently selected city.
Hour : Minutes
Seconds
Date
E-22
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, press D to display the city
code (time zone) whose Standard Time/Daylight Saving
Time setting you want to change.
2. Hold down A for about two seconds to toggle between
Daylight Saving Time (DST indicator displayed) and
Standard Time ( DST indicator not displayed).
• Holding down A will initially cause “Hold” to appear on
the screen. Keep A depressed until “Hold” disappears.
• The DST indicator is shown in the lower display while
Daylight Saving Time is turned on.
• You can turn on DST individually for each city code,
except UTC.
• Turning on DST for the city code that is currently
selected as your Home City will turn on DST for normal
timekeeping.
DST indicator
E-23
Swapping your Home City and World Time City
You can use the procedure below to swap your Home City and World Time City. This
changes your Home City to your World Time City, and your World Time City to your
Home City. This capability can come in handy when you frequently travel between two
cities in different time zones.
To swap your Home City and World Time City
1. In the World Time Mode, use D to select the World Time City you want.
2. Press A and B at the same time until the watch beeps.
• This will make the World Time City you selected in step 1 your Home City, and cause
the hour and minute hands to move to the current time in that city. At the same time,
it will change the Home City you had selected prior to step 2 your World Time City,
and cause the content of lower display to change accordingly.
• After swapping the Home City and World Time City, the watch stays in the World
Time Mode with the city that was selected as the Home City prior to step 2 now
displayed as the World Time City.
E-24
Alarms
When an alarm is turned on, the alarm tone will sound
when its alarm time is reached. One of the alarms is a
snooze alarm, while the other four are daily alarms.
You also can turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
• The snooze alarm screen is indicated by
, while the
other alarm screens are numbered
through . The
Hourly Time Signal screen is indicated by
.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C (page
E-7).
Alarm time
(Hour : Minutes)
E-25
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
DDDD
DD
• To set an alarm time, display the applicable alarm
screen (
through , or ).
•
is the hourly time signal setting (page E-28).
• The snooze alarm operation repeats every five
minutes.
2. After you select an alarm, hold down A for about two seconds until the hour setting
of the alarm time starts to flash. This is the setting mode.
•
Holding down A will initially cause “Hold” to appear on the screen. Keep A
depressed until “Hold” disappears.
• This operation turns on the alarm automatically.
3. Press C to move the flashing between the hour and minute settings.
OFF
E-26
4. While a setting is flashing, use D (+) and B (–) to change it.
5. Press A to exit the setting mode.
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, or until you turn the alarm off (page E-27).
• Alarm and Hourly Time Signal operations are performed in accordance with the
current time in your Home City, as kept in the Timekeeping Mode.
• To stop the alarm tone after it starts to sound, press any button.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen (page E-9)
Displaying the
setting screen (page E-25)
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
E-27
To turn an alarm on and off
1. In the Alarm Mode, use D to select an alarm.
2. Press A to toggle it on and off.
• Turning on a alarm (
, , , or ) displays
the alarm on indicator on its Alarm Mode screen.
• In all modes, the alarm on indicator is shown for any
alarm that currently is turned on.
• The alarm on indicator flashes while the alarm is
sounding.
• The snooze alarm indicator flashes while the snooze
alarm is sounding and during the 5-minute intervals
between alarms.
Alarm on indicator
Snooze alarm indicator
ON
E-28
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select the Hourly Time
Signal (
) (page E-25).
2. Press A to toggle it on and off.
• The Hourly Time Signal on indicator is shown on the
display in all modes while this function is turned on.
ON
Hourly time signal
on indicator
E-29
Illumination
An LED (light-emitting diode) illuminates the face of the
watch for easy reading in the dark. The watch’s auto light
switch turns on illumination automatically when you angle
the watch towards your face.
• The auto light switch must be turned on (indicated by
the auto light switch indicator) for it to operate.
• See “Illumination Precautions” (page E-38) for other
important information about using illumination.
To illuminate the display manually
In any mode, press B to turn on illumination.
• The above operation turns on illumination regardless of
the current auto light switch setting.
• You can use the procedure below to select either 1.5
seconds or 3 seconds as the illumination duration. When
you press B, the illumination will remain on for about
1.5 seconds or 3 seconds, depending on the current
illumination duration setting.
Auto light switch
indicator