Manualshelf

User manual

ManualsBrandsCasio ManualsWatch5259
123456
3. Tryck C för att ändra det blinkande displayinnehållet och välja de andra inställningarna i
sekvensen som visas nedan.
4. När tidvisningsinställningen som du vill ändra blinkar, använd D eller B för att ändra den enligt
beskrivningen nedan.
5. Tryck A för att lämna inställningsfunktionen.
• Veckodagen visas automatiskt enligt datuminställningen (år, månad och dag).
Sommartid (DST)
Sommartid (DST) innebär att man ställer fram klockan en timme i förhållande till Standardtiden.
Kom ihåg att vissa länder eller till och med lokala områden inte använder Sommartid.
Att justera inställning av sommartid (DST)
1. I Tidvisningsfunktionen, tryck och håll inne A i ca två sekunder tills
”SET” visas på displayen.
• Observera att om du håller A intryckt för länge (i ca fem sekunder)
kommer klockan att växla till en annan typ av inställningsfunktion
(sida E-33).
2. Tryck C. DST-inställningen visas på displayen.
Stoppur
Du kan använda stoppuret för att mäta tider och mellantider.
• Stoppurets digitala display kan visa upp till 999 timmar, 59 minuter,
59,99 sekunder. Stoppuret fortsätter att mäta tid tills du stoppar det.
Om det når gränsen ovan kommer mätningen av tiden att starta om
från noll.
• Tidtagningen fortsätter även om du lämnar Stoppursfunktionen.
• Alla inställningar i detta avsnitt utförs i Stoppursfunktionen som du
aktiverar genom att trycka C (sida E-7).
E-14
• Tryck D utan att nollställa tiden som visas på displayen för att återuppta tidtagningen från när
den senast stoppades (ackumulerad tidtagning).
• Den pågående tidtagningen fortsätter även om du lämnar Stoppursfunktionen. Indikatorskivan
visar i detta fall den aktuella minuträkningen.
E-16
Att använda nedräkningstimern
Tryck D i Nedräkningstimerfunktionen för att starta nedräkningstimern.
• När nedräkningen är klar ljuder ett alarm i 10 sekunder eller tills du stoppar det genom att
trycka på någon knapp.
• Nedräkningstiden nollställs automatiskt till startvärdet efter att alarmet stoppat.
• Tryck D medan nedräkning pågår för att pausa den.
Tryck D igen för att återuppta nedräkningen.
• För att stoppa nedräkningstimern helt ska du först pausa den (genom att trycka D) och sedan
trycka A. Nedräkningstiden återgår då till startvärdet.
E-18
Bruksanvisning 5259
Operation Guide 5259
E-10
3. Press C to change the flashing screen content in the sequence shown below to
select the other settings.
Seconds
12/24-Hour
Format
Hour Minutes
DST
Month Year
City
Code
Day
Illumination
Duration
Button
Operation Tone
C C
CCCCC
C CC C
4. When the timekeeping setting you want to change is flashing, use D or B to
change it as described below.
Change the city code
Toggle the DST setting between
Daylight Saving Time (
) and
Standard Time (
).
Use D (east) and B
(west).
Press D.
Screen:
To do this: Do this:
E-11
Screen: To do this: Do this:
Toggle between 12-hour (
) and
24-hour ( ) timekeeping
Reset the seconds to
Change the hour and minutes
Change the year, month, or day
Toggle the button operation tone
between
(on) and (off)
Toggle the display illumination
duration between 1.5 seconds (
)
and three seconds (
)
Press D.
Press D.
Use D (+) and B (–).
Press D.
Press D.
E-12
5. Press A to exit the setting mode.
• The day of the week is displayed automatically in accordance with the date (year,
month, and day) settings.
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down A for about two
seconds until “SET” appears on the display.
• Note that keeping A depressed too long (for about
five seconds) will cause a different type of setting
mode to be entered (page E-33).
2. Press C. This will display the DST setting screen.
DST indicator
E-13
3. Use D to toggle the DST setting on and off.
DST off ( ) DST on ( )
D
• The default DST setting is OFF ( ).
4. When the setting you want is selected, press A to exit the setting mode.
• The DST indicator appears to indicate that Daylight Saving Time is turned on.
12-hour and 24-hour timekeeping
• With the 12-hour format, the PM indicator (P) appears on the lower display for times
in the range of noon to 11:59 p.m. and no indicator appears for times in the range of
midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
the PM indicator (P).
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
E-14
Stopwatch
You can use the stopwatch to measure elapsed time and
split times.
• The digital display range of the stopwatch is 999 hours,
59 minutes, 59.99 seconds. The stopwatch continues to
run until you stop it. If it reaches the above limit, it will
restart the time measurement from zero.
• The stopwatch operation continues even if you exit the
Stopwatch Mode.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C (page
E-7).
E-15
Elapsed Time Measurement
In the Stopwatch Mode, press D to start and stop elapsed time measurement.
• Pressing A while elapsed time measurement is in progress will display the current
split time.
DAADA
Start
(Stopped) (Stopped)(Measurement)
Split
Split
cancel
Display
time resetStop
(Measured time
displayed.)
(Split time
displayed.)
(Measured time
displayed.)
E-16
Indicator disk
Elapsed time seconds
• First 1 minute only
Measurement status
STOP: Stopped
RUN: Measuring
• Except during display of
a split time.
SPL: Split time displayed
Measured time or split time
Hours
• Alternates with “SPL” during
split time display.
Minutes, seconds,
1/100 seconds
• Pressing D without resetting the displayed time will restart elapsed time
measurement from where it was last stopped (cumulative elapsed time
measurement).
• An ongoing elapsed time measurement operation continues even if you exit the
Stopwatch Mode. In this case, the indicator disk indicates the current minutes count.
E-17
Countdown Timer
You can set the countdown timer start time within a range
of one minute to 24 hours. An alarm sounds when the
countdown reaches zero.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C (page E-7).
Start time
(Hours : Minutes)
Seconds
E-18
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached, the alarm will sound for 10 seconds or
until you stop it by pressing any button.
• The countdown time is reset to its starting value automatically after the alarm stops.
• Press D while a countdown operation is in progress to pause it.
Press D again to resume the countdown.
• To stop a countdown timer operation completely, first pause it (by pressing D), and
then press A. This returns the countdown time to its starting value.
E-19
To configure countdown start time settings
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A for about two
seconds until the hour setting of the countdown start
time starts to flash. This is the setting mode.
• Holding down A will initially cause “Hold” to appear
on the screen. Keep A depressed until “Hold”
disappears.
• If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” (page
E-18) to display it.
2. Press C to move the flashing in the sequence shown
below, and select the setting you want to change.
Start Time
(Minutes)
Start Time
(Hours)
C
C
3. Press A to exit the setting mode.
Start time
(Hours : Minutes)
Operation Guide 5259
E-10
3. Press C to change the flashing screen content in the sequence shown below to
select the other settings.
Seconds
12/24-Hour
Format
Hour Minutes
DST
Month Year
City
Code
Day
Illumination
Duration
Button
Operation Tone
C C
CCCCC
C CC C
4. When the timekeeping setting you want to change is flashing, use D or B to
change it as described below.
Change the city code
Toggle the DST setting between
Daylight Saving Time (
) and
Standard Time (
).
Use D (east) and B
(west).
Press D.
Screen:
To do this: Do this:
E-11
Screen: To do this: Do this:
Toggle between 12-hour (
) and
24-hour ( ) timekeeping
Reset the seconds to
Change the hour and minutes
Change the year, month, or day
Toggle the button operation tone
between
(on) and (off)
Toggle the display illumination
duration between 1.5 seconds (
)
and three seconds (
)
Press D.
Press D.
Use D (+) and B (–).
Press D.
Press D.
E-12
5. Press A to exit the setting mode.
• The day of the week is displayed automatically in accordance with the date (year,
month, and day) settings.
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down A for about two
seconds until “SET” appears on the display.
• Note that keeping A depressed too long (for about
five seconds) will cause a different type of setting
mode to be entered (page E-33).
2. Press C. This will display the DST setting screen.
DST indicator
E-13
3. Use D to toggle the DST setting on and off.
DST off ( ) DST on ( )
D
• The default DST setting is OFF ( ).
4. When the setting you want is selected, press A to exit the setting mode.
• The DST indicator appears to indicate that Daylight Saving Time is turned on.
12-hour and 24-hour timekeeping
• With the 12-hour format, the PM indicator (P) appears on the lower display for times
in the range of noon to 11:59 p.m. and no indicator appears for times in the range of
midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
the PM indicator (P).
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
E-14
Stopwatch
You can use the stopwatch to measure elapsed time and
split times.
• The digital display range of the stopwatch is 999 hours,
59 minutes, 59.99 seconds. The stopwatch continues to
run until you stop it. If it reaches the above limit, it will
restart the time measurement from zero.
• The stopwatch operation continues even if you exit the
Stopwatch Mode.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C (page
E-7).
E-15
Elapsed Time Measurement
In the Stopwatch Mode, press D to start and stop elapsed time measurement.
• Pressing A while elapsed time measurement is in progress will display the current
split time.
DAADA
Start
(Stopped) (Stopped)(Measurement)
Split
Split
cancel
Display
time resetStop
(Measured time
displayed.)
(Split time
displayed.)
(Measured time
displayed.)
E-16
Indicator disk
Elapsed time seconds
• First 1 minute only
Measurement status
STOP: Stopped
RUN: Measuring
• Except during display of
a split time.
SPL: Split time displayed
Measured time or split time
Hours
• Alternates with “SPL” during
split time display.
Minutes, seconds,
1/100 seconds
• Pressing D without resetting the displayed time will restart elapsed time
measurement from where it was last stopped (cumulative elapsed time
measurement).
• An ongoing elapsed time measurement operation continues even if you exit the
Stopwatch Mode. In this case, the indicator disk indicates the current minutes count.
E-17
Countdown Timer
You can set the countdown timer start time within a range
of one minute to 24 hours. An alarm sounds when the
countdown reaches zero.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C (page E-7).
Start time
(Hours : Minutes)
Seconds
E-18
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached, the alarm will sound for 10 seconds or
until you stop it by pressing any button.
• The countdown time is reset to its starting value automatically after the alarm stops.
• Press D while a countdown operation is in progress to pause it.
Press D again to resume the countdown.
• To stop a countdown timer operation completely, first pause it (by pressing D), and
then press A. This returns the countdown time to its starting value.
E-19
To configure countdown start time settings
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A for about two
seconds until the hour setting of the countdown start
time starts to flash. This is the setting mode.
• Holding down A will initially cause “Hold” to appear
on the screen. Keep A depressed until “Hold”
disappears.
• If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” (page
E-18) to display it.
2. Press C to move the flashing in the sequence shown
below, and select the setting you want to change.
Start Time
(Minutes)
Start Time
(Hours)
C
C
3. Press A to exit the setting mode.
Start time
(Hours : Minutes)
Operation Guide 5259
E-10
3. Press C to change the flashing screen content in the sequence shown below to
select the other settings.
Seconds
12/24-Hour
Format
Hour Minutes
DST
Month Year
City
Code
Day
Illumination
Duration
Button
Operation Tone
C C
CCCCC
C CC C
4. When the timekeeping setting you want to change is flashing, use D or B to
change it as described below.
Change the city code
Toggle the DST setting between
Daylight Saving Time (
) and
Standard Time (
).
Use D (east) and B
(west).
Press D.
Screen:
To do this: Do this:
E-11
Screen: To do this: Do this:
Toggle between 12-hour (
) and
24-hour ( ) timekeeping
Reset the seconds to
Change the hour and minutes
Change the year, month, or day
Toggle the button operation tone
between
(on) and (off)
Toggle the display illumination
duration between 1.5 seconds (
)
and three seconds (
)
Press D.
Press D.
Use D (+) and B (–).
Press D.
Press D.
E-12
5. Press A to exit the setting mode.
• The day of the week is displayed automatically in accordance with the date (year,
month, and day) settings.
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down A for about two
seconds until “SET” appears on the display.
• Note that keeping A depressed too long (for about
five seconds) will cause a different type of setting
mode to be entered (page E-33).
2. Press C. This will display the DST setting screen.
DST indicator
E-13
3. Use D to toggle the DST setting on and off.
DST off ( ) DST on ( )
D
• The default DST setting is OFF ( ).
4. When the setting you want is selected, press A to exit the setting mode.
• The DST indicator appears to indicate that Daylight Saving Time is turned on.
12-hour and 24-hour timekeeping
• With the 12-hour format, the PM indicator (P) appears on the lower display for times
in the range of noon to 11:59 p.m. and no indicator appears for times in the range of
midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
the PM indicator (P).
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
E-14
Stopwatch
You can use the stopwatch to measure elapsed time and
split times.
• The digital display range of the stopwatch is 999 hours,
59 minutes, 59.99 seconds. The stopwatch continues to
run until you stop it. If it reaches the above limit, it will
restart the time measurement from zero.
• The stopwatch operation continues even if you exit the
Stopwatch Mode.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C (page
E-7).
E-15
Elapsed Time Measurement
In the Stopwatch Mode, press D to start and stop elapsed time measurement.
• Pressing A while elapsed time measurement is in progress will display the current
split time.
DAADA
Start
(Stopped) (Stopped)(Measurement)
Split
Split
cancel
Display
time resetStop
(Measured time
displayed.)
(Split time
displayed.)
(Measured time
displayed.)
E-16
Indicator disk
Elapsed time seconds
• First 1 minute only
Measurement status
STOP: Stopped
RUN: Measuring
• Except during display of
a split time.
SPL: Split time displayed
Measured time or split time
Hours
• Alternates with “SPL” during
split time display.
Minutes, seconds,
1/100 seconds
• Pressing D without resetting the displayed time will restart elapsed time
measurement from where it was last stopped (cumulative elapsed time
measurement).
• An ongoing elapsed time measurement operation continues even if you exit the
Stopwatch Mode. In this case, the indicator disk indicates the current minutes count.
E-17
Countdown Timer
You can set the countdown timer start time within a range
of one minute to 24 hours. An alarm sounds when the
countdown reaches zero.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C (page E-7).
Start time
(Hours : Minutes)
Seconds
E-18
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached, the alarm will sound for 10 seconds or
until you stop it by pressing any button.
• The countdown time is reset to its starting value automatically after the alarm stops.
• Press D while a countdown operation is in progress to pause it.
Press D again to resume the countdown.
• To stop a countdown timer operation completely, first pause it (by pressing D), and
then press A. This returns the countdown time to its starting value.
E-19
To configure countdown start time settings
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A for about two
seconds until the hour setting of the countdown start
time starts to flash. This is the setting mode.
• Holding down A will initially cause “Hold” to appear
on the screen. Keep A depressed until “Hold”
disappears.
• If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” (page
E-18) to display it.
2. Press C to move the flashing in the sequence shown
below, and select the setting you want to change.
Start Time
(Minutes)
Start Time
(Hours)
C
C
3. Press A to exit the setting mode.
Start time
(Hours : Minutes)
3. Använd D för att växla DST-inställning mellan ON och OFF.
• Standardinställningen för DST är OFF.
4. När du har valt önskad inställning, tryck A för att lämna inställningsfunktionen.
• DST-indikatorn visas på displayen för att indikera att Sommartid är aktiverad.
12- och 24-timmarsvisning
• När 12-timmarsvisning är vald visas PM-indikatorn (P) på den nedre displayen från klockan
12 på dagen till 23:59, medan ingen indikator visas mellan midnatt och 11:59.
• När 24-timmarsvisning är vald visas tiden från 00:00 till 23:59 utan någon PM-indikator (P).
• 12/24-timmarsvisningen som du väljer i Tidvisningsfunktionen gäller för alla funktioner.
E-13
Tidtagning
I Stoppursfunktionen, tryck D för att starta och stoppa tidtagningen.
• Tryck A medan tidtagningen pågår för att visa den aktuella mellantiden.
E-15
Nedräkningstimer
Du kan ställa in nedräkningstimerns starttid inom ett intervall från
en minut till 24 timmar. Ett alarm ljuder när nedräkningen når noll.
• Alla inställningar i detta avsnitt utförs i
Nedräkningstimerfunktionen som du aktiverar genom att trycka C
(sida E-7).
E-17
Att kongurera inställningarna för nedräkningens starttid
1. Medan nedräkningens starttid visas på displayen i Tidvisnings
funktionen, tryck och håll inne A i ca två sekunder tills timinställ
ningen för nedräkningens starttid börjar blinka. Detta är
inställningsfunktionen.
• När du trycker och håller inne A visas ”Hold” inledningsvis på
displayen. Håll A intryckt tills ”Hold” försvinner.
• Om nedräkningens starttid inte visas, följ proceduren under ”Att
använda nedräkningstimern” (sida E-18) för att visa den.
2. Tryck C för att ytta blinkanket i sekvensen som visas nedan
och välj inställningen som du vill justera.
3. Tryck A för att lämna inställningsfunktionen.
E-19
DST off ( ) DST on ( )
D
Operation Guide 5259
E-10
3. Press C to change the flashing screen content in the sequence shown below to
select the other settings.
Seconds
12/24-Hour
Format
Hour Minutes
DST
Month Year
City
Code
Day
Illumination
Duration
Button
Operation Tone
C C
CCCCC
C CC C
4. When the timekeeping setting you want to change is flashing, use D or B to
change it as described below.
Change the city code
Toggle the DST setting between
Daylight Saving Time (
) and
Standard Time (
).
Use D (east) and B
(west).
Press D.
Screen:
To do this: Do this:
E-11
Screen: To do this: Do this:
Toggle between 12-hour (
) and
24-hour ( ) timekeeping
Reset the seconds to
Change the hour and minutes
Change the year, month, or day
Toggle the button operation tone
between
(on) and (off)
Toggle the display illumination
duration between 1.5 seconds (
)
and three seconds (
)
Press D.
Press D.
Use D (+) and B (–).
Press D.
Press D.
E-12
5. Press A to exit the setting mode.
• The day of the week is displayed automatically in accordance with the date (year,
month, and day) settings.
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down A for about two
seconds until “SET” appears on the display.
• Note that keeping A depressed too long (for about
five seconds) will cause a different type of setting
mode to be entered (page E-33).
2. Press C. This will display the DST setting screen.
DST indicator
E-13
3. Use D to toggle the DST setting on and off.
DST off ( ) DST on ( )
D
• The default DST setting is OFF ( ).
4. When the setting you want is selected, press A to exit the setting mode.
• The DST indicator appears to indicate that Daylight Saving Time is turned on.
12-hour and 24-hour timekeeping
• With the 12-hour format, the PM indicator (P) appears on the lower display for times
in the range of noon to 11:59 p.m. and no indicator appears for times in the range of
midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
the PM indicator (P).
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
E-14
Stopwatch
You can use the stopwatch to measure elapsed time and
split times.
• The digital display range of the stopwatch is 999 hours,
59 minutes, 59.99 seconds. The stopwatch continues to
run until you stop it. If it reaches the above limit, it will
restart the time measurement from zero.
• The stopwatch operation continues even if you exit the
Stopwatch Mode.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C (page
E-7).
E-15
Elapsed Time Measurement
In the Stopwatch Mode, press D to start and stop elapsed time measurement.
• Pressing A while elapsed time measurement is in progress will display the current
split time.
DAADA
Start
(Stopped) (Stopped)(Measurement)
Split
Split
cancel
Display
time resetStop
(Measured time
displayed.)
(Split time
displayed.)
(Measured time
displayed.)
E-16
Indicator disk
Elapsed time seconds
• First 1 minute only
Measurement status
STOP: Stopped
RUN: Measuring
• Except during display of
a split time.
SPL: Split time displayed
Measured time or split time
Hours
• Alternates with “SPL” during
split time display.
Minutes, seconds,
1/100 seconds
• Pressing D without resetting the displayed time will restart elapsed time
measurement from where it was last stopped (cumulative elapsed time
measurement).
• An ongoing elapsed time measurement operation continues even if you exit the
Stopwatch Mode. In this case, the indicator disk indicates the current minutes count.
E-17
Countdown Timer
You can set the countdown timer start time within a range
of one minute to 24 hours. An alarm sounds when the
countdown reaches zero.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C (page E-7).
Start time
(Hours : Minutes)
Seconds
E-18
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached, the alarm will sound for 10 seconds or
until you stop it by pressing any button.
• The countdown time is reset to its starting value automatically after the alarm stops.
• Press D while a countdown operation is in progress to pause it.
Press D again to resume the countdown.
• To stop a countdown timer operation completely, first pause it (by pressing D), and
then press A. This returns the countdown time to its starting value.
E-19
To configure countdown start time settings
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A for about two
seconds until the hour setting of the countdown start
time starts to flash. This is the setting mode.
• Holding down A will initially cause “Hold” to appear
on the screen. Keep A depressed until “Hold”
disappears.
• If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” (page
E-18) to display it.
2. Press C to move the flashing in the sequence shown
below, and select the setting you want to change.
Start Time
(Minutes)
Start Time
(Hours)
C
C
3. Press A to exit the setting mode.
Start time
(Hours : Minutes)
Operation Guide 5259
E-10
3. Press C to change the flashing screen content in the sequence shown below to
select the other settings.
Seconds
12/24-Hour
Format
Hour Minutes
DST
Month Year
City
Code
Day
Illumination
Duration
Button
Operation Tone
C C
CCCCC
C CC C
4. When the timekeeping setting you want to change is flashing, use D or B to
change it as described below.
Change the city code
Toggle the DST setting between
Daylight Saving Time (
) and
Standard Time (
).
Use D (east) and B
(west).
Press D.
Screen:
To do this: Do this:
E-11
Screen: To do this: Do this:
Toggle between 12-hour (
) and
24-hour ( ) timekeeping
Reset the seconds to
Change the hour and minutes
Change the year, month, or day
Toggle the button operation tone
between
(on) and (off)
Toggle the display illumination
duration between 1.5 seconds (
)
and three seconds (
)
Press D.
Press D.
Use D (+) and B (–).
Press D.
Press D.
E-12
5. Press A to exit the setting mode.
• The day of the week is displayed automatically in accordance with the date (year,
month, and day) settings.
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down A for about two
seconds until “SET” appears on the display.
• Note that keeping A depressed too long (for about
five seconds) will cause a different type of setting
mode to be entered (page E-33).
2. Press C. This will display the DST setting screen.
DST indicator
E-13
3. Use D to toggle the DST setting on and off.
DST off ( ) DST on ( )
D
• The default DST setting is OFF ( ).
4. When the setting you want is selected, press A to exit the setting mode.
• The DST indicator appears to indicate that Daylight Saving Time is turned on.
12-hour and 24-hour timekeeping
• With the 12-hour format, the PM indicator (P) appears on the lower display for times
in the range of noon to 11:59 p.m. and no indicator appears for times in the range of
midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
the PM indicator (P).
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
E-14
Stopwatch
You can use the stopwatch to measure elapsed time and
split times.
• The digital display range of the stopwatch is 999 hours,
59 minutes, 59.99 seconds. The stopwatch continues to
run until you stop it. If it reaches the above limit, it will
restart the time measurement from zero.
• The stopwatch operation continues even if you exit the
Stopwatch Mode.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C (page
E-7).
E-15
Elapsed Time Measurement
In the Stopwatch Mode, press D to start and stop elapsed time measurement.
• Pressing A while elapsed time measurement is in progress will display the current
split time.
DAADA
Start
(Stopped) (Stopped)(Measurement)
Split
Split
cancel
Display
time resetStop
(Measured time
displayed.)
(Split time
displayed.)
(Measured time
displayed.)
E-16
Indicator disk
Elapsed time seconds
• First 1 minute only
Measurement status
STOP: Stopped
RUN: Measuring
• Except during display of
a split time.
SPL: Split time displayed
Measured time or split time
Hours
• Alternates with “SPL” during
split time display.
Minutes, seconds,
1/100 seconds
• Pressing D without resetting the displayed time will restart elapsed time
measurement from where it was last stopped (cumulative elapsed time
measurement).
• An ongoing elapsed time measurement operation continues even if you exit the
Stopwatch Mode. In this case, the indicator disk indicates the current minutes count.
E-17
Countdown Timer
You can set the countdown timer start time within a range
of one minute to 24 hours. An alarm sounds when the
countdown reaches zero.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C (page E-7).
Start time
(Hours : Minutes)
Seconds
E-18
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached, the alarm will sound for 10 seconds or
until you stop it by pressing any button.
• The countdown time is reset to its starting value automatically after the alarm stops.
• Press D while a countdown operation is in progress to pause it.
Press D again to resume the countdown.
• To stop a countdown timer operation completely, first pause it (by pressing D), and
then press A. This returns the countdown time to its starting value.
E-19
To configure countdown start time settings
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A for about two
seconds until the hour setting of the countdown start
time starts to flash. This is the setting mode.
• Holding down A will initially cause “Hold” to appear
on the screen. Keep A depressed until “Hold”
disappears.
• If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” (page
E-18) to display it.
2. Press C to move the flashing in the sequence shown
below, and select the setting you want to change.
Start Time
(Minutes)
Start Time
(Hours)
C
C
3. Press A to exit the setting mode.
Start time
(Hours : Minutes)
Operation Guide 5259
E-10
3. Press C to change the flashing screen content in the sequence shown below to
select the other settings.
Seconds
12/24-Hour
Format
Hour Minutes
DST
Month Year
City
Code
Day
Illumination
Duration
Button
Operation Tone
C C
CCCCC
C CC C
4. When the timekeeping setting you want to change is flashing, use D or B to
change it as described below.
Change the city code
Toggle the DST setting between
Daylight Saving Time (
) and
Standard Time (
).
Use D (east) and B
(west).
Press D.
Screen:
To do this: Do this:
E-11
Screen: To do this: Do this:
Toggle between 12-hour (
) and
24-hour ( ) timekeeping
Reset the seconds to
Change the hour and minutes
Change the year, month, or day
Toggle the button operation tone
between
(on) and (off)
Toggle the display illumination
duration between 1.5 seconds (
)
and three seconds (
)
Press D.
Press D.
Use D (+) and B (–).
Press D.
Press D.
E-12
5. Press A to exit the setting mode.
• The day of the week is displayed automatically in accordance with the date (year,
month, and day) settings.
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down A for about two
seconds until “SET” appears on the display.
• Note that keeping A depressed too long (for about
five seconds) will cause a different type of setting
mode to be entered (page E-33).
2. Press C. This will display the DST setting screen.
DST indicator
E-13
3. Use D to toggle the DST setting on and off.
DST off ( ) DST on ( )
D
• The default DST setting is OFF ( ).
4. When the setting you want is selected, press A to exit the setting mode.
• The DST indicator appears to indicate that Daylight Saving Time is turned on.
12-hour and 24-hour timekeeping
• With the 12-hour format, the PM indicator (P) appears on the lower display for times
in the range of noon to 11:59 p.m. and no indicator appears for times in the range of
midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
the PM indicator (P).
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
E-14
Stopwatch
You can use the stopwatch to measure elapsed time and
split times.
• The digital display range of the stopwatch is 999 hours,
59 minutes, 59.99 seconds. The stopwatch continues to
run until you stop it. If it reaches the above limit, it will
restart the time measurement from zero.
• The stopwatch operation continues even if you exit the
Stopwatch Mode.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C (page
E-7).
E-15
Elapsed Time Measurement
In the Stopwatch Mode, press D to start and stop elapsed time measurement.
• Pressing A while elapsed time measurement is in progress will display the current
split time.
DAADA
Start
(Stopped) (Stopped)(Measurement)
Split
Split
cancel
Display
time resetStop
(Measured time
displayed.)
(Split time
displayed.)
(Measured time
displayed.)
E-16
Indicator disk
Elapsed time seconds
• First 1 minute only
Measurement status
STOP: Stopped
RUN: Measuring
• Except during display of
a split time.
SPL: Split time displayed
Measured time or split time
Hours
• Alternates with “SPL” during
split time display.
Minutes, seconds,
1/100 seconds
• Pressing D without resetting the displayed time will restart elapsed time
measurement from where it was last stopped (cumulative elapsed time
measurement).
• An ongoing elapsed time measurement operation continues even if you exit the
Stopwatch Mode. In this case, the indicator disk indicates the current minutes count.
E-17
Countdown Timer
You can set the countdown timer start time within a range
of one minute to 24 hours. An alarm sounds when the
countdown reaches zero.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C (page E-7).
Start time
(Hours : Minutes)
Seconds
E-18
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached, the alarm will sound for 10 seconds or
until you stop it by pressing any button.
• The countdown time is reset to its starting value automatically after the alarm stops.
• Press D while a countdown operation is in progress to pause it.
Press D again to resume the countdown.
• To stop a countdown timer operation completely, first pause it (by pressing D), and
then press A. This returns the countdown time to its starting value.
E-19
To configure countdown start time settings
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A for about two
seconds until the hour setting of the countdown start
time starts to flash. This is the setting mode.
• Holding down A will initially cause “Hold” to appear
on the screen. Keep A depressed until “Hold”
disappears.
• If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” (page
E-18) to display it.
2. Press C to move the flashing in the sequence shown
below, and select the setting you want to change.
Start Time
(Minutes)
Start Time
(Hours)
C
C
3. Press A to exit the setting mode.
Start time
(Hours : Minutes)
Operation Guide 5259
E-10
3. Press C to change the flashing screen content in the sequence shown below to
select the other settings.
Seconds
12/24-Hour
Format
Hour Minutes
DST
Month Year
City
Code
Day
Illumination
Duration
Button
Operation Tone
C C
CCCCC
C CC C
4. When the timekeeping setting you want to change is flashing, use D or B to
change it as described below.
Change the city code
Toggle the DST setting between
Daylight Saving Time (
) and
Standard Time (
).
Use D (east) and B
(west).
Press D.
Screen:
To do this: Do this:
E-11
Screen: To do this: Do this:
Toggle between 12-hour (
) and
24-hour ( ) timekeeping
Reset the seconds to
Change the hour and minutes
Change the year, month, or day
Toggle the button operation tone
between
(on) and (off)
Toggle the display illumination
duration between 1.5 seconds (
)
and three seconds (
)
Press D.
Press D.
Use D (+) and B (–).
Press D.
Press D.
E-12
5. Press A to exit the setting mode.
• The day of the week is displayed automatically in accordance with the date (year,
month, and day) settings.
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down A for about two
seconds until “SET” appears on the display.
• Note that keeping A depressed too long (for about
five seconds) will cause a different type of setting
mode to be entered (page E-33).
2. Press C. This will display the DST setting screen.
DST indicator
E-13
3. Use D to toggle the DST setting on and off.
DST off ( ) DST on ( )
D
• The default DST setting is OFF ( ).
4. When the setting you want is selected, press A to exit the setting mode.
• The DST indicator appears to indicate that Daylight Saving Time is turned on.
12-hour and 24-hour timekeeping
• With the 12-hour format, the PM indicator (P) appears on the lower display for times
in the range of noon to 11:59 p.m. and no indicator appears for times in the range of
midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
the PM indicator (P).
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
E-14
Stopwatch
You can use the stopwatch to measure elapsed time and
split times.
• The digital display range of the stopwatch is 999 hours,
59 minutes, 59.99 seconds. The stopwatch continues to
run until you stop it. If it reaches the above limit, it will
restart the time measurement from zero.
• The stopwatch operation continues even if you exit the
Stopwatch Mode.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C (page
E-7).
E-15
Elapsed Time Measurement
In the Stopwatch Mode, press D to start and stop elapsed time measurement.
• Pressing A while elapsed time measurement is in progress will display the current
split time.
DAADA
Start
(Stopped) (Stopped)(Measurement)
Split
Split
cancel
Display
time resetStop
(Measured time
displayed.)
(Split time
displayed.)
(Measured time
displayed.)
E-16
Indicator disk
Elapsed time seconds
• First 1 minute only
Measurement status
STOP: Stopped
RUN: Measuring
• Except during display of
a split time.
SPL: Split time displayed
Measured time or split time
Hours
• Alternates with “SPL” during
split time display.
Minutes, seconds,
1/100 seconds
• Pressing D without resetting the displayed time will restart elapsed time
measurement from where it was last stopped (cumulative elapsed time
measurement).
• An ongoing elapsed time measurement operation continues even if you exit the
Stopwatch Mode. In this case, the indicator disk indicates the current minutes count.
E-17
Countdown Timer
You can set the countdown timer start time within a range
of one minute to 24 hours. An alarm sounds when the
countdown reaches zero.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C (page E-7).
Start time
(Hours : Minutes)
Seconds
E-18
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached, the alarm will sound for 10 seconds or
until you stop it by pressing any button.
• The countdown time is reset to its starting value automatically after the alarm stops.
• Press D while a countdown operation is in progress to pause it.
Press D again to resume the countdown.
• To stop a countdown timer operation completely, first pause it (by pressing D), and
then press A. This returns the countdown time to its starting value.
E-19
To configure countdown start time settings
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A for about two
seconds until the hour setting of the countdown start
time starts to flash. This is the setting mode.
• Holding down A will initially cause “Hold” to appear
on the screen. Keep A depressed until “Hold”
disappears.
• If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” (page
E-18) to display it.
2. Press C to move the flashing in the sequence shown
below, and select the setting you want to change.
Start Time
(Minutes)
Start Time
(Hours)
C
C
3. Press A to exit the setting mode.
Start time
(Hours : Minutes)
Operation Guide 5259
E-10
3. Press C to change the flashing screen content in the sequence shown below to
select the other settings.
Seconds
12/24-Hour
Format
Hour Minutes
DST
Month Year
City
Code
Day
Illumination
Duration
Button
Operation Tone
C C
CCCCC
C CC C
4. When the timekeeping setting you want to change is flashing, use D or B to
change it as described below.
Change the city code
Toggle the DST setting between
Daylight Saving Time (
) and
Standard Time (
).
Use D (east) and B
(west).
Press D.
Screen:
To do this: Do this:
E-11
Screen: To do this: Do this:
Toggle between 12-hour (
) and
24-hour ( ) timekeeping
Reset the seconds to
Change the hour and minutes
Change the year, month, or day
Toggle the button operation tone
between
(on) and (off)
Toggle the display illumination
duration between 1.5 seconds (
)
and three seconds (
)
Press D.
Press D.
Use D (+) and B (–).
Press D.
Press D.
E-12
5. Press A to exit the setting mode.
• The day of the week is displayed automatically in accordance with the date (year,
month, and day) settings.
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down A for about two
seconds until “SET” appears on the display.
• Note that keeping A depressed too long (for about
five seconds) will cause a different type of setting
mode to be entered (page E-33).
2. Press C. This will display the DST setting screen.
DST indicator
E-13
3. Use D to toggle the DST setting on and off.
DST off ( ) DST on ( )
D
• The default DST setting is OFF ( ).
4. When the setting you want is selected, press A to exit the setting mode.
• The DST indicator appears to indicate that Daylight Saving Time is turned on.
12-hour and 24-hour timekeeping
• With the 12-hour format, the PM indicator (P) appears on the lower display for times
in the range of noon to 11:59 p.m. and no indicator appears for times in the range of
midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
the PM indicator (P).
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
E-14
Stopwatch
You can use the stopwatch to measure elapsed time and
split times.
• The digital display range of the stopwatch is 999 hours,
59 minutes, 59.99 seconds. The stopwatch continues to
run until you stop it. If it reaches the above limit, it will
restart the time measurement from zero.
• The stopwatch operation continues even if you exit the
Stopwatch Mode.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C (page
E-7).
E-15
Elapsed Time Measurement
In the Stopwatch Mode, press D to start and stop elapsed time measurement.
• Pressing A while elapsed time measurement is in progress will display the current
split time.
DAADA
Start
(Stopped) (Stopped)(Measurement)
Split
Split
cancel
Display
time resetStop
(Measured time
displayed.)
(Split time
displayed.)
(Measured time
displayed.)
E-16
Indicator disk
Elapsed time seconds
• First 1 minute only
Measurement status
STOP: Stopped
RUN: Measuring
• Except during display of
a split time.
SPL: Split time displayed
Measured time or split time
Hours
• Alternates with “SPL” during
split time display.
Minutes, seconds,
1/100 seconds
• Pressing D without resetting the displayed time will restart elapsed time
measurement from where it was last stopped (cumulative elapsed time
measurement).
• An ongoing elapsed time measurement operation continues even if you exit the
Stopwatch Mode. In this case, the indicator disk indicates the current minutes count.
E-17
Countdown Timer
You can set the countdown timer start time within a range
of one minute to 24 hours. An alarm sounds when the
countdown reaches zero.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C (page E-7).
Start time
(Hours : Minutes)
Seconds
E-18
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached, the alarm will sound for 10 seconds or
until you stop it by pressing any button.
• The countdown time is reset to its starting value automatically after the alarm stops.
• Press D while a countdown operation is in progress to pause it.
Press D again to resume the countdown.
• To stop a countdown timer operation completely, first pause it (by pressing D), and
then press A. This returns the countdown time to its starting value.
E-19
To configure countdown start time settings
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A for about two
seconds until the hour setting of the countdown start
time starts to flash. This is the setting mode.
• Holding down A will initially cause “Hold” to appear
on the screen. Keep A depressed until “Hold”
disappears.
• If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” (page
E-18) to display it.
2. Press C to move the flashing in the sequence shown
below, and select the setting you want to change.
Start Time
(Minutes)
Start Time
(Hours)
C
C
3. Press A to exit the setting mode.
Start time
(Hours : Minutes)
Operation Guide 5259
E-10
3. Press C to change the flashing screen content in the sequence shown below to
select the other settings.
Seconds
12/24-Hour
Format
Hour Minutes
DST
Month Year
City
Code
Day
Illumination
Duration
Button
Operation Tone
C C
CCCCC
C CC C
4. When the timekeeping setting you want to change is flashing, use D or B to
change it as described below.
Change the city code
Toggle the DST setting between
Daylight Saving Time (
) and
Standard Time (
).
Use D (east) and B
(west).
Press D.
Screen:
To do this: Do this:
E-11
Screen: To do this: Do this:
Toggle between 12-hour (
) and
24-hour ( ) timekeeping
Reset the seconds to
Change the hour and minutes
Change the year, month, or day
Toggle the button operation tone
between
(on) and (off)
Toggle the display illumination
duration between 1.5 seconds (
)
and three seconds (
)
Press D.
Press D.
Use D (+) and B (–).
Press D.
Press D.
E-12
5. Press A to exit the setting mode.
• The day of the week is displayed automatically in accordance with the date (year,
month, and day) settings.
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down A for about two
seconds until “SET” appears on the display.
• Note that keeping A depressed too long (for about
five seconds) will cause a different type of setting
mode to be entered (page E-33).
2. Press C. This will display the DST setting screen.
DST indicator
E-13
3. Use D to toggle the DST setting on and off.
DST off ( ) DST on ( )
D
• The default DST setting is OFF ( ).
4. When the setting you want is selected, press A to exit the setting mode.
• The DST indicator appears to indicate that Daylight Saving Time is turned on.
12-hour and 24-hour timekeeping
• With the 12-hour format, the PM indicator (P) appears on the lower display for times
in the range of noon to 11:59 p.m. and no indicator appears for times in the range of
midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
the PM indicator (P).
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
E-14
Stopwatch
You can use the stopwatch to measure elapsed time and
split times.
• The digital display range of the stopwatch is 999 hours,
59 minutes, 59.99 seconds. The stopwatch continues to
run until you stop it. If it reaches the above limit, it will
restart the time measurement from zero.
• The stopwatch operation continues even if you exit the
Stopwatch Mode.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C (page
E-7).
E-15
Elapsed Time Measurement
In the Stopwatch Mode, press D to start and stop elapsed time measurement.
• Pressing A while elapsed time measurement is in progress will display the current
split time.
DAADA
Start
(Stopped) (Stopped)(Measurement)
Split
Split
cancel
Display
time resetStop
(Measured time
displayed.)
(Split time
displayed.)
(Measured time
displayed.)
E-16
Indicator disk
Elapsed time seconds
• First 1 minute only
Measurement status
STOP: Stopped
RUN: Measuring
• Except during display of
a split time.
SPL: Split time displayed
Measured time or split time
Hours
• Alternates with “SPL” during
split time display.
Minutes, seconds,
1/100 seconds
• Pressing D without resetting the displayed time will restart elapsed time
measurement from where it was last stopped (cumulative elapsed time
measurement).
• An ongoing elapsed time measurement operation continues even if you exit the
Stopwatch Mode. In this case, the indicator disk indicates the current minutes count.
E-17
Countdown Timer
You can set the countdown timer start time within a range
of one minute to 24 hours. An alarm sounds when the
countdown reaches zero.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C (page E-7).
Start time
(Hours : Minutes)
Seconds
E-18
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached, the alarm will sound for 10 seconds or
until you stop it by pressing any button.
• The countdown time is reset to its starting value automatically after the alarm stops.
• Press D while a countdown operation is in progress to pause it.
Press D again to resume the countdown.
• To stop a countdown timer operation completely, first pause it (by pressing D), and
then press A. This returns the countdown time to its starting value.
E-19
To configure countdown start time settings
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A for about two
seconds until the hour setting of the countdown start
time starts to flash. This is the setting mode.
• Holding down A will initially cause “Hold” to appear
on the screen. Keep A depressed until “Hold”
disappears.
• If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” (page
E-18) to display it.
2. Press C to move the flashing in the sequence shown
below, and select the setting you want to change.
Start Time
(Minutes)
Start Time
(Hours)
C
C
3. Press A to exit the setting mode.
Start time
(Hours : Minutes)
Operation Guide 5259
E-10
3. Press C to change the flashing screen content in the sequence shown below to
select the other settings.
Seconds
12/24-Hour
Format
Hour Minutes
DST
Month Year
City
Code
Day
Illumination
Duration
Button
Operation Tone
C C
CCCCC
C CC C
4. When the timekeeping setting you want to change is flashing, use D or B to
change it as described below.
Change the city code
Toggle the DST setting between
Daylight Saving Time (
) and
Standard Time (
).
Use D (east) and B
(west).
Press D.
Screen:
To do this: Do this:
E-11
Screen: To do this: Do this:
Toggle between 12-hour (
) and
24-hour ( ) timekeeping
Reset the seconds to
Change the hour and minutes
Change the year, month, or day
Toggle the button operation tone
between
(on) and (off)
Toggle the display illumination
duration between 1.5 seconds (
)
and three seconds (
)
Press D.
Press D.
Use D (+) and B (–).
Press D.
Press D.
E-12
5. Press A to exit the setting mode.
• The day of the week is displayed automatically in accordance with the date (year,
month, and day) settings.
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down A for about two
seconds until “SET” appears on the display.
• Note that keeping A depressed too long (for about
five seconds) will cause a different type of setting
mode to be entered (page E-33).
2. Press C. This will display the DST setting screen.
DST indicator
E-13
3. Use D to toggle the DST setting on and off.
DST off ( ) DST on ( )
D
• The default DST setting is OFF ( ).
4. When the setting you want is selected, press A to exit the setting mode.
• The DST indicator appears to indicate that Daylight Saving Time is turned on.
12-hour and 24-hour timekeeping
• With the 12-hour format, the PM indicator (P) appears on the lower display for times
in the range of noon to 11:59 p.m. and no indicator appears for times in the range of
midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
the PM indicator (P).
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
E-14
Stopwatch
You can use the stopwatch to measure elapsed time and
split times.
• The digital display range of the stopwatch is 999 hours,
59 minutes, 59.99 seconds. The stopwatch continues to
run until you stop it. If it reaches the above limit, it will
restart the time measurement from zero.
• The stopwatch operation continues even if you exit the
Stopwatch Mode.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C (page
E-7).
E-15
Elapsed Time Measurement
In the Stopwatch Mode, press D to start and stop elapsed time measurement.
• Pressing A while elapsed time measurement is in progress will display the current
split time.
DAADA
Start
(Stopped) (Stopped)(Measurement)
Split
Split
cancel
Display
time resetStop
(Measured time
displayed.)
(Split time
displayed.)
(Measured time
displayed.)
E-16
Indicator disk
Elapsed time seconds
• First 1 minute only
Measurement status
STOP: Stopped
RUN: Measuring
• Except during display of
a split time.
SPL: Split time displayed
Measured time or split time
Hours
• Alternates with “SPL” during
split time display.
Minutes, seconds,
1/100 seconds
• Pressing D without resetting the displayed time will restart elapsed time
measurement from where it was last stopped (cumulative elapsed time
measurement).
• An ongoing elapsed time measurement operation continues even if you exit the
Stopwatch Mode. In this case, the indicator disk indicates the current minutes count.
E-17
Countdown Timer
You can set the countdown timer start time within a range
of one minute to 24 hours. An alarm sounds when the
countdown reaches zero.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C (page E-7).
Start time
(Hours : Minutes)
Seconds
E-18
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached, the alarm will sound for 10 seconds or
until you stop it by pressing any button.
• The countdown time is reset to its starting value automatically after the alarm stops.
• Press D while a countdown operation is in progress to pause it.
Press D again to resume the countdown.
• To stop a countdown timer operation completely, first pause it (by pressing D), and
then press A. This returns the countdown time to its starting value.
E-19
To configure countdown start time settings
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A for about two
seconds until the hour setting of the countdown start
time starts to flash. This is the setting mode.
• Holding down A will initially cause “Hold” to appear
on the screen. Keep A depressed until “Hold”
disappears.
• If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” (page
E-18) to display it.
2. Press C to move the flashing in the sequence shown
below, and select the setting you want to change.
Start Time
(Minutes)
Start Time
(Hours)
C
C
3. Press A to exit the setting mode.
Start time
(Hours : Minutes)