User manual

1
Operation Guide 5134
MA1007-EB
About This Manual
Depending on the model of your watch, its display may have dark figures on a light •
background or light figures on a dark background. The display also may be with a
graphic area or without a graphic area. All samples in this manual show dark figures
on a light background, with a graphic area.
Button operations are indicated using the letters shown in the illustration. •
For the sake of simplicity, the sample displays in this manual do not show the analog •
hands of the watch.
Each section of this manual provides you with the information you need to perform •
operations in each mode. Further details and technical information can be found in
the “Reference” section.
With graphic area Without graphic area
Graphic area
General Guide
Press • C to change from mode to mode.
In any mode (except when a setting screen is on the display), press • B to illuminate
the display.
Timekeeping Mode World Time Mode Alarm Mode Stopwatch Mode Countdown Timer
Mode
Press C.
When the setting you want to change is flashing, use 4. B and D to change it as
described below.
Screen To do this: Do this:
Reset the seconds to
Press D.
Toggle between Daylight Saving Time ( )
and Standard Time ( )
Press D.
Change the Home City code
Use D (east) and B (west).
Change the hour or minutes
Use D (+) and B (–).
Toggle between 12-hour ( ) and 24-hour
( ) timekeeping
Press D.
Change the year
Use D (+) and B (–).
Change the month or day
Press 5. A to exit the setting screen.
Resetting the seconds only (without changing the DST, Home City code, hour, or •
minute setting) causes the analog minute hand setting to be adjusted automatically.
See “Digital Time Daylight Saving Time (DST) Setting” below for details about the •
DST setting.
The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is •
applied in all modes.
Digital Time Daylight Saving Time (DST) Setting
Daylight Saving Time (summer time) advances the digital time setting by one hour
from Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To toggle the Timekeeping Mode digital time between DST and Standard Time
In the Timekeeping Mode, hold down 1. A until the
seconds start to flash, which indicates the setting
screen.
Press 2. C once to display the DST setting screen.
Press 3. D to toggle between Daylight Saving Time
(
displayed) and Standard Time ( displayed).
Press 4. A to exit the setting screen.
The DST indicator appears on the Timekeeping Mode •
screen to indicate that Daylight Saving Time is turned on.
Analog Time Setting
Perform the procedure below when the time indicated by the analog hands does not
match the time of the digital display.
To adjust the analog time
In the Timekeeping Mode, hold down 1. D for about three
seconds until the lower right display first shows H-SET
and then the current digital time. This is the analog hand
adjustment mode.
Press 2. D to advance the analog time setting by 20
seconds.
Holding down • D advances the analog time setting at
high speed.
If you need to advance the analog time setting a long •
way, hold down D until the time starts advancing at
high speed, and then press B. This locks the high-
speed hand movement, so you can release the button.
High-speed hand movement continues until you press
any button. It will also stop automatically after the time
advances 12 hours or if an alarm (daily alarm, Hourly
Time Signal, or countdown beeper) starts to sound.
DST indicator
Timekeeping
This watch features separate digital and analog timekeeping. The procedures for
setting the digital time and analog time are different.
In the Timekeeping Mode, you can press • D to change the display format as shown
below.
Day of the Week
and Day
Hour : Minutes
Seconds
Press D.
Hour : MinutesDayDay of week
PM indicator
Digital Time and Date
Use the Timekeeping Mode to set and view a digital display of the current time and
date. When setting the digital time, you can also configure settings for summer time
(Daylight Saving Time or DST), your Home City code (the code for the city where you
normally use the watch), the 12/24-hour format.
This watch is preset with a number of city codes, each of which represents the time •
zone where that city is located. When setting the digital time, it is important that you
select the correct city code for your Home City. If your location is not included in the
preset city codes, select the preset city code that is in the same time zone as your
location.
Note that all of the times for the World Time Mode city codes are displayed in •
accordance with the digital time and date settings you configure in the Timekeeping
Mode.
After you correctly set your Home City time and date, you can set the watch up for •
timekeeping with a different city code simply by changing the Home City code in the
Timekeeping Mode.
To set the digital time and date
In the Timekeeping Mode, hold down 1. A until the
seconds start to flash, which indicates the setting
screen.
Press 2. C twice to move the flashing to the Home City
code setting, and then use B and D to select the code
you want.
Make sure you select your Home City code before •
changing any other setting.
For full information on city codes, see the “City Code •
Table”.
Press 3. C to move the flashing in the sequence shown below to select the other
settings.
Seconds DST Home City Code Hour Minutes
12/24-Hour FormatYearMonthDay