User manual

Operation Guide ANA(ST5)V.A
2
Hour hand
First click
(Setting day)
Second click
(Setting time)
Crown
(Normal position)
Day
Second hand
Minute hand
Setting the Time and
Day
To set the time
1. Pull the crown out to the second click.
• At this time, the second hand will move to the
12 o’clock position and stop there.
2. Set the hands by rotating the crown. Rotate the
crown to move the hands clockwise. Move the
minute hand four or five minutes past the time
you want to set, and then back it up to the
proper setting.
• Carefully set the time, making sure to
distinguish between AM and PM.
3. Push the crown back in to the normal position
to restart timekeeping.
To set the day
1. Pull the crown out to the first click.
2. Set the day by rotating the crown towards you.
3. Push the crown back in to the normal position.
• Avoid changing the date setting while the
current time is between 9:00 p.m. and 1:00 a.m.
• Some water resistant models are equipped
with a screw lock crown.
• With such models, you must unscrew the
crown in the direction noted in the
illustration to loosen it before you can pull it
out. Do not pull too forcibly on such crowns.
• Also note that such watches are not water
resistant while their crowns are loosened.
Be sure to screw the crowns back in as far
as they will go after making any setting.
● The watch attached with a bezel can
measure the elapsed time. Align the ▼
mark on the bezel with the minute hand
by turning it so that the time elapsed from
the ▼ mark can be measured.
Elapsed
time
Start
Using the Stopwatch
Stopwatch hour hand
Stopwatch 1/20 second
hand
* This hand rotates and
indicates the 1/20 second
count durin
g
the first 30 seconds.
Stopwatch minute hand
Stopwatch second hand
The stopwatch lets you measure elapsed time up
to 11 hours, 59 minutes, 59.95 seconds.
To measure elapsed time
1. Press A to start the stopwatch.
2. Press A to stop the stopwatch.
• You can resume the measurement operation
by pressing A again.
The stopwatch 1/20 second hand rotates and
indicates the 1/20 second count during the
first 30 seconds.
3. Check the elapsed time.
• The example below shows an elapsed time of
two minutes, 18.80 seconds.
Stopwatch 1/20 second
hand [80]
Stopwatch minute hand
[2 minutes]
Stopwatch second hand
[18 seconds]
• Press B to reset the stopwatch.
This will enter the Timekeeping Mode.
To return the function of the stopwatch 1/20
second hand to the timekeeping seconds
hand (indicating the current seconds count),
press B again.
Notes:
• Do not try to perform stopwatch operations
while the crown is pulled out either to the first or
second click. If you try to press a button, you
might accidentally cause the crown to rotate and
change the current time or day setting.
• If the starting positions of the stopwatch second
hand and 1/20 second hand become mis-
aligned, use the following procedures to adjust
the positions of the hands so they point to 12
o’clock when the stopwatch is reset.
To adjust the positions of the stopwatch
hands
1. Press B to reset the stopwatch, and check the
alignment of the stopwatch second hand and
1/20 second hand.
2. Pull out the crown to the second click.
3. Press A to move the stopwatch second hand.
• Holding down A will start high-speed
movement of the stopwatch second hand.
4. Press B.
5. If the stopwatch 1/20 second hand is aligned
correctly, proceed to step 6. If the stopwatch
1/20 second hand is also misaligned, press B
to move the stopwatch 1/20 second hand.
• Holding down B will start high-speed
movement of the stopwatch 1/20 second
hand.
6. After making the adjustments you want, push
the crown back in to its normal position.
• Note that pulling the crown out also stops the
timekeeping second hand. After performing the
above procedure, you should also adjust the
timekeeping setting.