User manual

Operation Guide ANA(ST3)V.A
2
Setting the Time and Date
• Some water resistant models are equipped with
a screw lock crown.
• With such models, you must unscrew the crown
in the direction noted in the illustration to loosen
it before you can pull it out. Do not pull too
forcibly on such crowns.
• Also note that such watches are not water
resistant while their crowns are loosened. Be
sure to screw the crowns back in as far as they
will go after making any setting.
Crow
n
● The watch attached with a bezel can
measure the elapsed time. Align the ▼
mark on the bezel with the minute hand by
turning it so that the time elapsed from the
▼ mark can be measured.
Elapsed
time
Start
Minute hand
24-hour hand
Hour hand
First click (Setting day)
Second click
(Setting time)
Crown (Normal position)
Day
Second hand
To set the time
1. Pull the crown out to the second click.
• At this time, the second hand will move to the 12
o’clock position and stop there.
2. Set the hands by rotating the crown. Rotate the
crown to move the hands clockwise. Move the
minute hand four or five minutes past the time
you want to set, and then back it up to the proper
setting.
• Make sure that you also set the 24-hour hand to the
correct hour of the day.
3. Push the crown back in to the normal position to
restart timekeeping.
To set the day
1. Pull the crown out to the first click.
2. Set the day by rotating the crown towards you.
3. Push the crown back in to the normal position.
• Avoid changing the date setting while the current time
is between 9:00 p.m. and 1:00 a.m.
Using the Stopwatch
Stopwatch second
hand
Stopwatch 1/100
second hand
Stopwatch minute
hand
* This hand rotates
and indicates the
second count
during the first 60
seconds.
The stopwatch lets you measure elapsed time up to
59 minutes, 59.99 seconds.
To measure elapsed time (First 60 seconds)
1. Press A to start the stopwatch.
2. Press A to stop the stopwatch.
• You can resume the measurement operation by
pressing A again.
3. Check the elapsed time.
• The example below shows an elapsed time of
44.30 seconds.
Stopwatch 1/100
second hand
[30]
Stopwatch second
hand
[44 seconds]
• Press B to reset the stopwatch.
This will enter the Timekeeping Mode.
To measure elapsed time (After the first 60 seconds)
1. Press A to start the stopwatch.
• During elapsed time measurement, the stopwatch
1/100 second hand automatically rotates for the
final second of each minute.
2. Press A to stop the stopwatch.
• You can resume the measurement operation by
pressing A again.
3. Press the A button, and the stopwatch 1/100
second hand will move to the 1/100 second
count.
• If the elapsed time operation was stopped during
the final second of each minute, the stopwatch
1/100 second hand will already be pointing at the
1/100 second count. Do not press the A button at
this time, because doing so will restart the elapsed
time operation.
4. Check the elapsed time.
• The example below shows an elapsed time of two
minutes, 44.30 seconds.
Stopwatch second hand
[44 seconds]
Stopwatch minute
hand
[2 minutes]
Stopwatch 1/100
second hand
[30]
• Press B to reset the stopwatch.
This will enter the Timekeeping Mode.
Notes:
• Do not try to perform stopwatch operations while the
crown is pulled out either to the first or second click. If
you try to press a button, you might accidentally
cause the crown to rotate and change the current
time or day setting.
• If the starting positions of the stopwatch second hand
and 1/100 second hand become misaligned, use the
following procedures to adjust the positions of the
hands so they point to 12 o’clock when the stopwatch
is reset.
To adjust the positions of the stopwatch hands
1. Press B to reset the stopwatch, and check the
alignment of the stopwatch second hand and
1/100 second hand.
2. Pull out the crown to the second click.
3. Press A to move the stopwatch 1/100 second
hand.
4. If the stopwatch minute hand is aligned
correctly, proceed to step 5. If the stopwatch
minute hand is also misaligned, press B to
move the stopwatch second hand.
5. After making the adjustments you want, push
the crown back in to its normal position.
• Note that pulling the crown out also stops the
timekeeping second hand. After performing the
above procedure, you should also adjust the
timekeeping setting.