User manual

Bruksanvisning 3403
Observera!
■ Om en tidigare nedräkning stoppades i Timerfunktionen innan den nått noll, återupptas
nedräkningen när du trycker D.
■ D-knappen är avaktiverad om en nedräkning som startades i Timerfunktionen fortfarande
pågår.
■ En pågående nedräkning (som startades antingen i Timerfunktionen eller Tidvisningsfunktio-
nen) kan inte stoppas eller nollställas i Tidvisningsfunktionen.
◊ Att visa timerns starttid
■ I Tidvisningsfunktionen, tryck A.
Detta får timerns starttid (som du ställde in med proceduren på sida E-36) att visas i en sekund
på displayen istället för veckodagen och datumet.
E-40
Övriga inställningar
Du kan använda procedurerna i detta avsnitt för att aktivera/avaktivera ljudet som låter när du
trycker på en knapp.
Du kan även välja signalmetod for alarm och timer mellan ljudsignal och blinkande displaybe-
lysning eller vibrationssignal.
Att aktivera/avaktivera knappljudet
1. I Tidvisningsfunktionen, tryck och håll inne A i ca två
sekunder tills inställningsdisplayen för tidszoner visas.
E-42
4. Tryck A för att återgå till Tidvisningsfunktionen.
Observera!
Proceduren ovan påverkar endast knappljudet. Alarmet, timsignalen och slutsignalen påverkas
inte.
Att ändra signalmetod for alarm/timer
1. I Tidvisningsfunktionen, tryck och håll inne A i ca två
sekunder tills inställningsdisplayen för tidszoner visas.
2. Tryck C 11 gånger för att visa inställningsdisplayen för
signaler.
Se ”Inställning av aktuell tid och datum” (sida E-15).
Displayen visar antingen [VIB] eller [FLASH].
E-44
Belysning
Genom att följa proceduren nedan kan du belysa displayen för att underlätta avläsning i
mörker.
Att belysa displayen
■ Tryck L för att belysa displayen.
Observera!
Belysningen stängs av automatiskt om den är på när ett förinställt alarm aktiveras eller
nedräkningen når noll.
◊ Försiktighetsåtgärder vid användning av belysning
Om belysningen används ofta kan batteriets livslängd förkortas.
E-46
Att aktivera/avaktivera automatisk belysning
Indikator för automatisk
belysning PÅ ■ I Tidvisningsfunktionen, tryck och håll inne L i minst tre
sekunder.
Detta växlar den automatiska belysningen mellan aktiverad
(Indikator för automatisk belysning PÅ) och avaktiverad.
E-48
Observera!
■ Om en nedräkning stoppades i Timerfunktionen innan den nått noll, visas den aktuella
(stoppade) nedräkningstiden när du trycker A i Tidvisningsfunktionen.
■ När en nedräkning pågår visas den på displayen. Du kan växla till displayen för veckodagen
och datumet genom att trycka A.
Att stoppa en ljud-/vibrationssignal
■ Tryck på valfri knapp för att stoppa en pågående ljud-/vibrationssignal.
E-41
2. Tryck C nio gånger för att visa inställningsdisplayen för
knappljud.
Se ”Inställning av aktuell tid och datum” (sida E-15).
Displayen visar antingen [KEY ] eller [MUTE].
MUTE-indikator
3. Tryck D för att växla inställning mellan [KEY ] (PÅ) och
[MUTE] (AV).
När [MUTE] (AV) har valts visas en MUTE-indikator för att indikera
att knappljudet är avaktiverat.
E-43
Vibrationsindikator
3. Tryck D för att växla inställning mellan [VIB] och [FLASH].
Vibrationsindikatorn visas på displayen när [VIB] har valts.
: vibrationssignal.
: ljudsignal och blinkande displaybelysning.
4. Tryck A för att återgå till Tidvisningsfunktionen.
◊ Att testa vibrationssignalen
■ I Tidvisningsfunktionen, tryck och håll inne B för att testa vibrationssignalen.
E-45
Användning av automatisk belysning
När den automatiska belysningen är aktiverad, tänds displaybelysningen om du vänder
klockan mot dig med en vinkel på minst 40˚.
40˚ eller större
Observera!
Den automatiska belysningen avaktiveras automatiskt när ett alarm ljuder.
E-47
Försiktighetsåtgärder vid automatisk belysning
■ Det är inte säkert att den automatiska belysningen fungerar korrekt om din arm
vinklas horisontellt mer än 15˚ såsom visas i illustrationen.
■ Statisk elektricitet eller magnetism kan hindra den automatiska belysningens
funktion. Om detta inträffar, försök med att sänka armen och höja den igen.
■ Det är möjligt att du hör ett skramlande ljud från klockan när du vinklar den mot
ditt ansikte. Detta ljud kommer från den automatiska belysningen och indikerar
inte att det är fel på klockan.
■ Den automatiska belysningen förblir aktiverad i endast sex timmar, för att
sedan avaktiveras automatiskt.
E-49
Operation Guide 3403
E-49
Auto Light Precautions
Auto Light may not work properly if your arm is angled horizontally x
15˚ or more as shown in the illustration.
The presence of static electricity or magnetism can cause Auto x
Light not to work. If this happens, try lowering your arm and
raising it back up again.
You may notice a rattling sound inside the watch when you angle x
it towards your face. This is the sound of the Auto Light switch,
and does not indicate malfunction.
Auto Light remains enabled only for about six hours. After that it is x
disabled automatically.
E-48
To enable or disable Auto Light
●
In the Timekeeping Mode, hold down
L
for at least
three seconds.
This will toggle Auto Light between enabled (Auto Light
ON indicator displayed) and disabled.
Auto Light ON indicator
E-47
Using Auto Light
When Auto Light is enabled, angling the watch towards your face at an angle of 40˚
or greater will illuminate the display automatically.
40˚ or greater
Note
Auto Light is disabled automatically while an alarm is sounding.
E-46
Illumination
You can use the procedure below to illuminate the display for easy reading in the
dark.
To illuminate the display
●
Press
L
to illuminate the display.
Note
Illumination will turn off automatically if it is on when an alarm time or the end of a
countdown is reached.
Light Use Precautions ◆
Frequent use of the light can shorten battery life.
E-45
●
Press
3
D
to toggle the setting between [VIB] and
[FLASH].
The Vibration indicator is shown on the display while
[VIB] is selected.
: Alert by vibration.
:
Alert by tone and fl ashing display
illumination.
●
To return to the Timekeeping Mode, press
4
A
.
To test vibration ◆
●
In the Timekeeping Mode, hold down
B
to perform the vibration operation.
Vibration indicator
E-44
●
To return to the Timekeeping Mode, press
4
A
.
Note
The above procedure affects the button operation tone only. The alarm, hourly time
signal, and time up alarm are not affected.
To change the alarm/timer alert method
●
In the Timekeeping Mode, hold down
1
A
for about
two seconds until the time zone setting screen
appears.
1
●
Press
2
C
11 times to display alert setting screen.
See “Confi guring Current Time and Date Settings”
(page E-15).
The screen will show either [VIB] or [FLASH].
E-43
●
Press
2
C
nine times to display the button
operation tone setting screen.
See “Confi guring Current Time and Date Settings”
(page E-15).
The screen will show either [KEY
] or [MUTE].
MUTE indicator
●
Press
3
D
to toggle the setting between
[KEY
] (ON) and [MUTE] (OFF).
When [MUTE] (OFF) is selected, a MUTE indicator is
displayed to indicate that the button operation tone
will not sound.
E-42
Other Settings
You can use the procedures in this section to turn the tone that sounds when you
press a button on or off.
You can also select either tone and display illumination fl ashing, or vibration as the
alert method for the alarm and timer.
To turn the button operation tone on or off
●
In the Timekeeping Mode, hold down
1
A
for about
two seconds until the time zone setting screen
appears.
E-41
Note
If a countdown was stopped part way through in the Timer Mode, the current x
(stopped) countdown time will be displayed when you press A in the Timekeeping
Mode.
While a countdown is in progress, the display will show the countdown. You can x
switch to display of the day of the week and day by pressing A.
To stop a tone/vibration alert operation
●
Pressing any one of the buttons will stop an ongoing tone/vibration alert
operation.
E-40
Note
If a previous countdown was stopped part way through in the Timer Mode, x
pressing D will resume the countdown.
The x D button will be disabled if a countdown that was started in the Timer Mode
is still in progress.
An ongoing countdown (started in either the Timer Mode or Timekeeping Mode) x
cannot be stopped or reset in the Timekeeping Mode.
To view the timer start time ◆
●
In the Timekeeping Mode, press
A
.
This will cause the timer start time (the start time you set with the procedure on
page E-36) to appear for one second in the display in place of the day of the
week and day.
Operation Guide 3403
E-49
Auto Light Precautions
Auto Light may not work properly if your arm is angled horizontally x
15˚ or more as shown in the illustration.
The presence of static electricity or magnetism can cause Auto x
Light not to work. If this happens, try lowering your arm and
raising it back up again.
You may notice a rattling sound inside the watch when you angle x
it towards your face. This is the sound of the Auto Light switch,
and does not indicate malfunction.
Auto Light remains enabled only for about six hours. After that it is x
disabled automatically.
E-48
To enable or disable Auto Light
●
In the Timekeeping Mode, hold down
L
for at least
three seconds.
This will toggle Auto Light between enabled (Auto Light
ON indicator displayed) and disabled.
Auto Light ON indicator
E-47
Using Auto Light
When Auto Light is enabled, angling the watch towards your face at an angle of 40˚
or greater will illuminate the display automatically.
40˚ or greater
Note
Auto Light is disabled automatically while an alarm is sounding.
E-46
Illumination
You can use the procedure below to illuminate the display for easy reading in the
dark.
To illuminate the display
●
Press
L
to illuminate the display.
Note
Illumination will turn off automatically if it is on when an alarm time or the end of a
countdown is reached.
Light Use Precautions ◆
Frequent use of the light can shorten battery life.
E-45
●
Press
3
D
to toggle the setting between [VIB] and
[FLASH].
The Vibration indicator is shown on the display while
[VIB] is selected.
: Alert by vibration.
:
Alert by tone and fl ashing display
illumination.
●
To return to the Timekeeping Mode, press
4
A
.
To test vibration ◆
●
In the Timekeeping Mode, hold down
B
to perform the vibration operation.
Vibration indicator
E-44
●
To return to the Timekeeping Mode, press
4
A
.
Note
The above procedure affects the button operation tone only. The alarm, hourly time
signal, and time up alarm are not affected.
To change the alarm/timer alert method
●
In the Timekeeping Mode, hold down
1
A
for about
two seconds until the time zone setting screen
appears.
1
●
Press
2
C
11 times to display alert setting screen.
See “Confi guring Current Time and Date Settings”
(page E-15).
The screen will show either [VIB] or [FLASH].
E-43
●
Press
2
C nine times to display the button
operation tone setting screen.
See “Confi guring Current Time and Date Settings”
(page E-15).
The screen will show either [KEY
] or [MUTE].
MUTE indicator
●
Press
3
D to toggle the setting between
[KEY
] (ON) and [MUTE] (OFF).
When [MUTE] (OFF) is selected, a MUTE indicator is
displayed to indicate that the button operation tone
will not sound.
E-42
Other Settings
You can use the procedures in this section to turn the tone that sounds when you
press a button on or off.
You can also select either tone and display illumination fl ashing, or vibration as the
alert method for the alarm and timer.
To turn the button operation tone on or off
●
In the Timekeeping Mode, hold down
1
A
for about
two seconds until the time zone setting screen
appears.
E-41
Note
If a countdown was stopped part way through in the Timer Mode, the current x
(stopped) countdown time will be displayed when you press A in the Timekeeping
Mode.
While a countdown is in progress, the display will show the countdown. You can x
switch to display of the day of the week and day by pressing A.
To stop a tone/vibration alert operation
●
Pressing any one of the buttons will stop an ongoing tone/vibration alert
operation.
E-40
Note
If a previous countdown was stopped part way through in the Timer Mode, x
pressing D will resume the countdown.
The x D button will be disabled if a countdown that was started in the Timer Mode
is still in progress.
An ongoing countdown (started in either the Timer Mode or Timekeeping Mode) x
cannot be stopped or reset in the Timekeeping Mode.
To view the timer start time ◆
●
In the Timekeeping Mode, press
A
.
This will cause the timer start time (the start time you set with the procedure on
page E-36) to appear for one second in the display in place of the day of the
week and day.
Operation Guide 3403
E-49
Auto Light Precautions
Auto Light may not work properly if your arm is angled horizontally x
15˚ or more as shown in the illustration.
The presence of static electricity or magnetism can cause Auto x
Light not to work. If this happens, try lowering your arm and
raising it back up again.
You may notice a rattling sound inside the watch when you angle x
it towards your face. This is the sound of the Auto Light switch,
and does not indicate malfunction.
Auto Light remains enabled only for about six hours. After that it is x
disabled automatically.
E-48
To enable or disable Auto Light
●
In the Timekeeping Mode, hold down
L
for at least
three seconds.
This will toggle Auto Light between enabled (Auto Light
ON indicator displayed) and disabled.
Auto Light ON indicator
E-47
Using Auto Light
When Auto Light is enabled, angling the watch towards your face at an angle of 40˚
or greater will illuminate the display automatically.
40˚ or greater
Note
Auto Light is disabled automatically while an alarm is sounding.
E-46
Illumination
You can use the procedure below to illuminate the display for easy reading in the
dark.
To illuminate the display
●
Press
L
to illuminate the display.
Note
Illumination will turn off automatically if it is on when an alarm time or the end of a
countdown is reached.
Light Use Precautions ◆
Frequent use of the light can shorten battery life.
E-45
●
Press
3
D
to toggle the setting between [VIB] and
[FLASH].
The Vibration indicator is shown on the display while
[VIB] is selected.
: Alert by vibration.
:
Alert by tone and fl ashing display
illumination.
●
To return to the Timekeeping Mode, press
4
A
.
To test vibration ◆
●
In the Timekeeping Mode, hold down
B
to perform the vibration operation.
Vibration indicator
E-44
●
To return to the Timekeeping Mode, press
4
A
.
Note
The above procedure affects the button operation tone only. The alarm, hourly time
signal, and time up alarm are not affected.
To change the alarm/timer alert method
●
In the Timekeeping Mode, hold down
1
A
for about
two seconds until the time zone setting screen
appears.
1
●
Press
2
C
11 times to display alert setting screen.
See “Confi guring Current Time and Date Settings”
(page E-15).
The screen will show either [VIB] or [FLASH].
E-43
●
Press
2
C nine times to display the button
operation tone setting screen.
See “Confi guring Current Time and Date Settings”
(page E-15).
The screen will show either [KEY
] or [MUTE].
MUTE indicator
●
Press
3
D to toggle the setting between
[KEY
] (ON) and [MUTE] (OFF).
When [MUTE] (OFF) is selected, a MUTE indicator is
displayed to indicate that the button operation tone
will not sound.
E-42
Other Settings
You can use the procedures in this section to turn the tone that sounds when you
press a button on or off.
You can also select either tone and display illumination fl ashing, or vibration as the
alert method for the alarm and timer.
To turn the button operation tone on or off
●
In the Timekeeping Mode, hold down
1
A
for about
two seconds until the time zone setting screen
appears.
E-41
Note
If a countdown was stopped part way through in the Timer Mode, the current x
(stopped) countdown time will be displayed when you press A in the Timekeeping
Mode.
While a countdown is in progress, the display will show the countdown. You can x
switch to display of the day of the week and day by pressing A.
To stop a tone/vibration alert operation
●
Pressing any one of the buttons will stop an ongoing tone/vibration alert
operation.
E-40
Note
If a previous countdown was stopped part way through in the Timer Mode, x
pressing D will resume the countdown.
The x D button will be disabled if a countdown that was started in the Timer Mode
is still in progress.
An ongoing countdown (started in either the Timer Mode or Timekeeping Mode) x
cannot be stopped or reset in the Timekeeping Mode.
To view the timer start time ◆
●
In the Timekeeping Mode, press
A
.
This will cause the timer start time (the start time you set with the procedure on
page E-36) to appear for one second in the display in place of the day of the
week and day.
Operation Guide 3403
E-49
Auto Light Precautions
Auto Light may not work properly if your arm is angled horizontally x
15˚ or more as shown in the illustration.
The presence of static electricity or magnetism can cause Auto x
Light not to work. If this happens, try lowering your arm and
raising it back up again.
You may notice a rattling sound inside the watch when you angle x
it towards your face. This is the sound of the Auto Light switch,
and does not indicate malfunction.
Auto Light remains enabled only for about six hours. After that it is x
disabled automatically.
E-48
To enable or disable Auto Light
●
In the Timekeeping Mode, hold down
L
for at least
three seconds.
This will toggle Auto Light between enabled (Auto Light
ON indicator displayed) and disabled.
Auto Light ON indicator
E-47
Using Auto Light
When Auto Light is enabled, angling the watch towards your face at an angle of 40˚
or greater will illuminate the display automatically.
40˚ or greater
Note
Auto Light is disabled automatically while an alarm is sounding.
E-46
Illumination
You can use the procedure below to illuminate the display for easy reading in the
dark.
To illuminate the display
●
Press
L
to illuminate the display.
Note
Illumination will turn off automatically if it is on when an alarm time or the end of a
countdown is reached.
Light Use Precautions ◆
Frequent use of the light can shorten battery life.
E-45
●
Press
3
D
to toggle the setting between [VIB] and
[FLASH].
The Vibration indicator is shown on the display while
[VIB] is selected.
: Alert by vibration.
:
Alert by tone and fl ashing display
illumination.
●
To return to the Timekeeping Mode, press
4
A
.
To test vibration ◆
●
In the Timekeeping Mode, hold down
B
to perform the vibration operation.
Vibration indicator
E-44
●
To return to the Timekeeping Mode, press
4
A
.
Note
The above procedure affects the button operation tone only. The alarm, hourly time
signal, and time up alarm are not affected.
To change the alarm/timer alert method
●
In the Timekeeping Mode, hold down
1
A
for about
two seconds until the time zone setting screen
appears.
1
●
Press
2
C
11 times to display alert setting screen.
See “Confi guring Current Time and Date Settings”
(page E-15).
The screen will show either [VIB] or [FLASH].
E-43
●
Press
2
C
nine times to display the button
operation tone setting screen.
See “Confi guring Current Time and Date Settings”
(page E-15).
The screen will show either [KEY
] or [MUTE].
MUTE indicator
●
Press
3
D
to toggle the setting between
[KEY
] (ON) and [MUTE] (OFF).
When [MUTE] (OFF) is selected, a MUTE indicator is
displayed to indicate that the button operation tone
will not sound.
E-42
Other Settings
You can use the procedures in this section to turn the tone that sounds when you
press a button on or off.
You can also select either tone and display illumination fl ashing, or vibration as the
alert method for the alarm and timer.
To turn the button operation tone on or off
●
In the Timekeeping Mode, hold down
1
A
for about
two seconds until the time zone setting screen
appears.
E-41
Note
If a countdown was stopped part way through in the Timer Mode, the current x
(stopped) countdown time will be displayed when you press A in the Timekeeping
Mode.
While a countdown is in progress, the display will show the countdown. You can x
switch to display of the day of the week and day by pressing A.
To stop a tone/vibration alert operation
●
Pressing any one of the buttons will stop an ongoing tone/vibration alert
operation.
E-40
Note
If a previous countdown was stopped part way through in the Timer Mode, x
pressing D will resume the countdown.
The x D button will be disabled if a countdown that was started in the Timer Mode
is still in progress.
An ongoing countdown (started in either the Timer Mode or Timekeeping Mode) x
cannot be stopped or reset in the Timekeeping Mode.
To view the timer start time ◆
●
In the Timekeeping Mode, press
A
.
This will cause the timer start time (the start time you set with the procedure on
page E-36) to appear for one second in the display in place of the day of the
week and day.
Operation Guide 3403
E-49
Auto Light Precautions
Auto Light may not work properly if your arm is angled horizontally x
15˚ or more as shown in the illustration.
The presence of static electricity or magnetism can cause Auto x
Light not to work. If this happens, try lowering your arm and
raising it back up again.
You may notice a rattling sound inside the watch when you angle x
it towards your face. This is the sound of the Auto Light switch,
and does not indicate malfunction.
Auto Light remains enabled only for about six hours. After that it is x
disabled automatically.
E-48
To enable or disable Auto Light
●
In the Timekeeping Mode, hold down
L
for at least
three seconds.
This will toggle Auto Light between enabled (Auto Light
ON indicator displayed) and disabled.
Auto Light ON indicator
E-47
Using Auto Light
When Auto Light is enabled, angling the watch towards your face at an angle of 40˚
or greater will illuminate the display automatically.
40˚ or greater
Note
Auto Light is disabled automatically while an alarm is sounding.
E-46
Illumination
You can use the procedure below to illuminate the display for easy reading in the
dark.
To illuminate the display
●
Press
L
to illuminate the display.
Note
Illumination will turn off automatically if it is on when an alarm time or the end of a
countdown is reached.
Light Use Precautions ◆
Frequent use of the light can shorten battery life.
E-45
●
Press
3
D to toggle the setting between [VIB] and
[FLASH].
The Vibration indicator is shown on the display while
[VIB] is selected.
: Alert by vibration.
:
Alert by tone and fl ashing display
illumination.
●
To return to the Timekeeping Mode, press
4
A.
To test vibration ◆
●
In the Timekeeping Mode, hold down B to perform the vibration operation.
Vibration indicator
E-44
●
To return to the Timekeeping Mode, press
4
A
.
Note
The above procedure affects the button operation tone only. The alarm, hourly time
signal, and time up alarm are not affected.
To change the alarm/timer alert method
●
In the Timekeeping Mode, hold down
1
A
for about
two seconds until the time zone setting screen
appears.
1
●
Press
2
C
11 times to display alert setting screen.
See “Confi guring Current Time and Date Settings”
(page E-15).
The screen will show either [VIB] or [FLASH].
E-43
●
Press
2
C
nine times to display the button
operation tone setting screen.
See “Confi guring Current Time and Date Settings”
(page E-15).
The screen will show either [KEY
] or [MUTE].
MUTE indicator
●
Press
3
D
to toggle the setting between
[KEY
] (ON) and [MUTE] (OFF).
When [MUTE] (OFF) is selected, a MUTE indicator is
displayed to indicate that the button operation tone
will not sound.
E-42
Other Settings
You can use the procedures in this section to turn the tone that sounds when you
press a button on or off.
You can also select either tone and display illumination fl ashing, or vibration as the
alert method for the alarm and timer.
To turn the button operation tone on or off
●
In the Timekeeping Mode, hold down
1
A
for about
two seconds until the time zone setting screen
appears.
E-41
Note
If a countdown was stopped part way through in the Timer Mode, the current x
(stopped) countdown time will be displayed when you press A in the Timekeeping
Mode.
While a countdown is in progress, the display will show the countdown. You can x
switch to display of the day of the week and day by pressing A.
To stop a tone/vibration alert operation
●
Pressing any one of the buttons will stop an ongoing tone/vibration alert
operation.
E-40
Note
If a previous countdown was stopped part way through in the Timer Mode, x
pressing D will resume the countdown.
The x D button will be disabled if a countdown that was started in the Timer Mode
is still in progress.
An ongoing countdown (started in either the Timer Mode or Timekeeping Mode) x
cannot be stopped or reset in the Timekeeping Mode.
To view the timer start time ◆
●
In the Timekeeping Mode, press
A
.
This will cause the timer start time (the start time you set with the procedure on
page E-36) to appear for one second in the display in place of the day of the
week and day.
Operation Guide 3403
E-49
Auto Light Precautions
Auto Light may not work properly if your arm is angled horizontally x
15˚ or more as shown in the illustration.
The presence of static electricity or magnetism can cause Auto x
Light not to work. If this happens, try lowering your arm and
raising it back up again.
You may notice a rattling sound inside the watch when you angle x
it towards your face. This is the sound of the Auto Light switch,
and does not indicate malfunction.
Auto Light remains enabled only for about six hours. After that it is x
disabled automatically.
E-48
To enable or disable Auto Light
●
In the Timekeeping Mode, hold down
L
for at least
three seconds.
This will toggle Auto Light between enabled (Auto Light
ON indicator displayed) and disabled.
Auto Light ON indicator
E-47
Using Auto Light
When Auto Light is enabled, angling the watch towards your face at an angle of 40˚
or greater will illuminate the display automatically.
40˚ or greater
Note
Auto Light is disabled automatically while an alarm is sounding.
E-46
Illumination
You can use the procedure below to illuminate the display for easy reading in the
dark.
To illuminate the display
●
Press
L
to illuminate the display.
Note
Illumination will turn off automatically if it is on when an alarm time or the end of a
countdown is reached.
Light Use Precautions ◆
Frequent use of the light can shorten battery life.
E-45
●
Press
3
D to toggle the setting between [VIB] and
[FLASH].
The Vibration indicator is shown on the display while
[VIB] is selected.
: Alert by vibration.
:
Alert by tone and fl ashing display
illumination.
●
To return to the Timekeeping Mode, press
4
A.
To test vibration ◆
●
In the Timekeeping Mode, hold down B to perform the vibration operation.
Vibration indicator
E-44
●
To return to the Timekeeping Mode, press
4
A
.
Note
The above procedure affects the button operation tone only. The alarm, hourly time
signal, and time up alarm are not affected.
To change the alarm/timer alert method
●
In the Timekeeping Mode, hold down
1
A
for about
two seconds until the time zone setting screen
appears.
1
●
Press
2
C
11 times to display alert setting screen.
See “Confi guring Current Time and Date Settings”
(page E-15).
The screen will show either [VIB] or [FLASH].
E-43
●
Press
2
C
nine times to display the button
operation tone setting screen.
See “Confi guring Current Time and Date Settings”
(page E-15).
The screen will show either [KEY
] or [MUTE].
MUTE indicator
●
Press
3
D
to toggle the setting between
[KEY
] (ON) and [MUTE] (OFF).
When [MUTE] (OFF) is selected, a MUTE indicator is
displayed to indicate that the button operation tone
will not sound.
E-42
Other Settings
You can use the procedures in this section to turn the tone that sounds when you
press a button on or off.
You can also select either tone and display illumination fl ashing, or vibration as the
alert method for the alarm and timer.
To turn the button operation tone on or off
●
In the Timekeeping Mode, hold down
1
A
for about
two seconds until the time zone setting screen
appears.
E-41
Note
If a countdown was stopped part way through in the Timer Mode, the current x
(stopped) countdown time will be displayed when you press A in the Timekeeping
Mode.
While a countdown is in progress, the display will show the countdown. You can x
switch to display of the day of the week and day by pressing A.
To stop a tone/vibration alert operation
●
Pressing any one of the buttons will stop an ongoing tone/vibration alert
operation.
E-40
Note
If a previous countdown was stopped part way through in the Timer Mode, x
pressing D will resume the countdown.
The x D button will be disabled if a countdown that was started in the Timer Mode
is still in progress.
An ongoing countdown (started in either the Timer Mode or Timekeeping Mode) x
cannot be stopped or reset in the Timekeeping Mode.
To view the timer start time ◆
●
In the Timekeeping Mode, press
A
.
This will cause the timer start time (the start time you set with the procedure on
page E-36) to appear for one second in the display in place of the day of the
week and day.
Operation Guide 3403
E-49
Auto Light Precautions
Auto Light may not work properly if your arm is angled horizontally x
15˚ or more as shown in the illustration.
The presence of static electricity or magnetism can cause Auto x
Light not to work. If this happens, try lowering your arm and
raising it back up again.
You may notice a rattling sound inside the watch when you angle x
it towards your face. This is the sound of the Auto Light switch,
and does not indicate malfunction.
Auto Light remains enabled only for about six hours. After that it is x
disabled automatically.
E-48
To enable or disable Auto Light
●
In the Timekeeping Mode, hold down
L
for at least
three seconds.
This will toggle Auto Light between enabled (Auto Light
ON indicator displayed) and disabled.
Auto Light ON indicator
E-47
Using Auto Light
When Auto Light is enabled, angling the watch towards your face at an angle of 40˚
or greater will illuminate the display automatically.
40˚ or greater
Note
Auto Light is disabled automatically while an alarm is sounding.
E-46
Illumination
You can use the procedure below to illuminate the display for easy reading in the
dark.
To illuminate the display
●
Press
L
to illuminate the display.
Note
Illumination will turn off automatically if it is on when an alarm time or the end of a
countdown is reached.
Light Use Precautions ◆
Frequent use of the light can shorten battery life.
E-45
●
Press
3
D to toggle the setting between [VIB] and
[FLASH].
The Vibration indicator is shown on the display while
[VIB] is selected.
: Alert by vibration.
:
Alert by tone and fl ashing display
illumination.
●
To return to the Timekeeping Mode, press
4
A.
To test vibration ◆
●
In the Timekeeping Mode, hold down B to perform the vibration operation.
Vibration indicator
E-44
●
To return to the Timekeeping Mode, press
4
A
.
Note
The above procedure affects the button operation tone only. The alarm, hourly time
signal, and time up alarm are not affected.
To change the alarm/timer alert method
●
In the Timekeeping Mode, hold down
1
A
for about
two seconds until the time zone setting screen
appears.
1
●
Press
2
C
11 times to display alert setting screen.
See “Confi guring Current Time and Date Settings”
(page E-15).
The screen will show either [VIB] or [FLASH].
E-43
●
Press
2
C
nine times to display the button
operation tone setting screen.
See “Confi guring Current Time and Date Settings”
(page E-15).
The screen will show either [KEY
] or [MUTE].
MUTE indicator
●
Press
3
D
to toggle the setting between
[KEY
] (ON) and [MUTE] (OFF).
When [MUTE] (OFF) is selected, a MUTE indicator is
displayed to indicate that the button operation tone
will not sound.
E-42
Other Settings
You can use the procedures in this section to turn the tone that sounds when you
press a button on or off.
You can also select either tone and display illumination fl ashing, or vibration as the
alert method for the alarm and timer.
To turn the button operation tone on or off
●
In the Timekeeping Mode, hold down
1
A
for about
two seconds until the time zone setting screen
appears.
E-41
Note
If a countdown was stopped part way through in the Timer Mode, the current x
(stopped) countdown time will be displayed when you press A in the Timekeeping
Mode.
While a countdown is in progress, the display will show the countdown. You can x
switch to display of the day of the week and day by pressing A.
To stop a tone/vibration alert operation
●
Pressing any one of the buttons will stop an ongoing tone/vibration alert
operation.
E-40
Note
If a previous countdown was stopped part way through in the Timer Mode, x
pressing D will resume the countdown.
The x D button will be disabled if a countdown that was started in the Timer Mode
is still in progress.
An ongoing countdown (started in either the Timer Mode or Timekeeping Mode) x
cannot be stopped or reset in the Timekeeping Mode.
To view the timer start time ◆
●
In the Timekeeping Mode, press
A
.
This will cause the timer start time (the start time you set with the procedure on
page E-36) to appear for one second in the display in place of the day of the
week and day.
Operation Guide 3403
E-49
Auto Light Precautions
Auto Light may not work properly if your arm is angled horizontally x
15˚ or more as shown in the illustration.
The presence of static electricity or magnetism can cause Auto x
Light not to work. If this happens, try lowering your arm and
raising it back up again.
You may notice a rattling sound inside the watch when you angle x
it towards your face. This is the sound of the Auto Light switch,
and does not indicate malfunction.
Auto Light remains enabled only for about six hours. After that it is x
disabled automatically.
E-48
To enable or disable Auto Light
●
In the Timekeeping Mode, hold down
L
for at least
three seconds.
This will toggle Auto Light between enabled (Auto Light
ON indicator displayed) and disabled.
Auto Light ON indicator
E-47
Using Auto Light
When Auto Light is enabled, angling the watch towards your face at an angle of 40˚
or greater will illuminate the display automatically.
40˚ or greater
Note
Auto Light is disabled automatically while an alarm is sounding.
E-46
Illumination
You can use the procedure below to illuminate the display for easy reading in the
dark.
To illuminate the display
●
Press
L
to illuminate the display.
Note
Illumination will turn off automatically if it is on when an alarm time or the end of a
countdown is reached.
Light Use Precautions ◆
Frequent use of the light can shorten battery life.
E-45
●
Press
3
D
to toggle the setting between [VIB] and
[FLASH].
The Vibration indicator is shown on the display while
[VIB] is selected.
: Alert by vibration.
:
Alert by tone and fl ashing display
illumination.
●
To return to the Timekeeping Mode, press
4
A
.
To test vibration ◆
●
In the Timekeeping Mode, hold down
B
to perform the vibration operation.
Vibration indicator
E-44
●
To return to the Timekeeping Mode, press
4
A
.
Note
The above procedure affects the button operation tone only. The alarm, hourly time
signal, and time up alarm are not affected.
To change the alarm/timer alert method
●
In the Timekeeping Mode, hold down
1
A
for about
two seconds until the time zone setting screen
appears.
1
●
Press
2
C
11 times to display alert setting screen.
See “Confi guring Current Time and Date Settings”
(page E-15).
The screen will show either [VIB] or [FLASH].
E-43
●
Press
2
C
nine times to display the button
operation tone setting screen.
See “Confi guring Current Time and Date Settings”
(page E-15).
The screen will show either [KEY
] or [MUTE].
MUTE indicator
●
Press
3
D
to toggle the setting between
[KEY
] (ON) and [MUTE] (OFF).
When [MUTE] (OFF) is selected, a MUTE indicator is
displayed to indicate that the button operation tone
will not sound.
E-42
Other Settings
You can use the procedures in this section to turn the tone that sounds when you
press a button on or off.
You can also select either tone and display illumination fl ashing, or vibration as the
alert method for the alarm and timer.
To turn the button operation tone on or off
●
In the Timekeeping Mode, hold down
1
A
for about
two seconds until the time zone setting screen
appears.
E-41
Note
If a countdown was stopped part way through in the Timer Mode, the current x
(stopped) countdown time will be displayed when you press A in the Timekeeping
Mode.
While a countdown is in progress, the display will show the countdown. You can x
switch to display of the day of the week and day by pressing A.
To stop a tone/vibration alert operation
●
Pressing any one of the buttons will stop an ongoing tone/vibration alert
operation.
E-40
Note
If a previous countdown was stopped part way through in the Timer Mode, x
pressing D will resume the countdown.
The x D button will be disabled if a countdown that was started in the Timer Mode
is still in progress.
An ongoing countdown (started in either the Timer Mode or Timekeeping Mode) x
cannot be stopped or reset in the Timekeeping Mode.
To view the timer start time ◆
●
In the Timekeeping Mode, press
A
.
This will cause the timer start time (the start time you set with the procedure on
page E-36) to appear for one second in the display in place of the day of the
week and day.
Operation Guide 3403
E-49
Auto Light Precautions
Auto Light may not work properly if your arm is angled horizontally x
15˚ or more as shown in the illustration.
The presence of static electricity or magnetism can cause Auto x
Light not to work. If this happens, try lowering your arm and
raising it back up again.
You may notice a rattling sound inside the watch when you angle x
it towards your face. This is the sound of the Auto Light switch,
and does not indicate malfunction.
Auto Light remains enabled only for about six hours. After that it is x
disabled automatically.
E-48
To enable or disable Auto Light
●
In the Timekeeping Mode, hold down
L
for at least
three seconds.
This will toggle Auto Light between enabled (Auto Light
ON indicator displayed) and disabled.
Auto Light ON indicator
E-47
Using Auto Light
When Auto Light is enabled, angling the watch towards your face at an angle of 40˚
or greater will illuminate the display automatically.
40˚ or greater
Note
Auto Light is disabled automatically while an alarm is sounding.
E-46
Illumination
You can use the procedure below to illuminate the display for easy reading in the
dark.
To illuminate the display
●
Press
L
to illuminate the display.
Note
Illumination will turn off automatically if it is on when an alarm time or the end of a
countdown is reached.
Light Use Precautions ◆
Frequent use of the light can shorten battery life.
E-45
●
Press
3
D
to toggle the setting between [VIB] and
[FLASH].
The Vibration indicator is shown on the display while
[VIB] is selected.
: Alert by vibration.
:
Alert by tone and fl ashing display
illumination.
●
To return to the Timekeeping Mode, press
4
A
.
To test vibration ◆
●
In the Timekeeping Mode, hold down
B
to perform the vibration operation.
Vibration indicator
E-44
●
To return to the Timekeeping Mode, press
4
A
.
Note
The above procedure affects the button operation tone only. The alarm, hourly time
signal, and time up alarm are not affected.
To change the alarm/timer alert method
●
In the Timekeeping Mode, hold down
1
A
for about
two seconds until the time zone setting screen
appears.
1
●
Press
2
C
11 times to display alert setting screen.
See “Confi guring Current Time and Date Settings”
(page E-15).
The screen will show either [VIB] or [FLASH].
E-43
●
Press
2
C
nine times to display the button
operation tone setting screen.
See “Confi guring Current Time and Date Settings”
(page E-15).
The screen will show either [KEY
] or [MUTE].
MUTE indicator
●
Press
3
D
to toggle the setting between
[KEY
] (ON) and [MUTE] (OFF).
When [MUTE] (OFF) is selected, a MUTE indicator is
displayed to indicate that the button operation tone
will not sound.
E-42
Other Settings
You can use the procedures in this section to turn the tone that sounds when you
press a button on or off.
You can also select either tone and display illumination fl ashing, or vibration as the
alert method for the alarm and timer.
To turn the button operation tone on or off
●
In the Timekeeping Mode, hold down
1
A
for about
two seconds until the time zone setting screen
appears.
E-41
Note
If a countdown was stopped part way through in the Timer Mode, the current x
(stopped) countdown time will be displayed when you press A in the Timekeeping
Mode.
While a countdown is in progress, the display will show the countdown. You can x
switch to display of the day of the week and day by pressing A.
To stop a tone/vibration alert operation
●
Pressing any one of the buttons will stop an ongoing tone/vibration alert
operation.
E-40
Note
If a previous countdown was stopped part way through in the Timer Mode, x
pressing D will resume the countdown.
The x D button will be disabled if a countdown that was started in the Timer Mode
is still in progress.
An ongoing countdown (started in either the Timer Mode or Timekeeping Mode) x
cannot be stopped or reset in the Timekeeping Mode.
To view the timer start time ◆
●
In the Timekeeping Mode, press
A
.
This will cause the timer start time (the start time you set with the procedure on
page E-36) to appear for one second in the display in place of the day of the
week and day.
Operation Guide 3403
E-49
Auto Light Precautions
Auto Light may not work properly if your arm is angled horizontally x
15˚ or more as shown in the illustration.
The presence of static electricity or magnetism can cause Auto x
Light not to work. If this happens, try lowering your arm and
raising it back up again.
You may notice a rattling sound inside the watch when you angle x
it towards your face. This is the sound of the Auto Light switch,
and does not indicate malfunction.
Auto Light remains enabled only for about six hours. After that it is x
disabled automatically.
E-48
To enable or disable Auto Light
●
In the Timekeeping Mode, hold down
L
for at least
three seconds.
This will toggle Auto Light between enabled (Auto Light
ON indicator displayed) and disabled.
Auto Light ON indicator
E-47
Using Auto Light
When Auto Light is enabled, angling the watch towards your face at an angle of 40˚
or greater will illuminate the display automatically.
40˚ or greater
Note
Auto Light is disabled automatically while an alarm is sounding.
E-46
Illumination
You can use the procedure below to illuminate the display for easy reading in the
dark.
To illuminate the display
●
Press
L
to illuminate the display.
Note
Illumination will turn off automatically if it is on when an alarm time or the end of a
countdown is reached.
Light Use Precautions ◆
Frequent use of the light can shorten battery life.
E-45
●
Press
3
D
to toggle the setting between [VIB] and
[FLASH].
The Vibration indicator is shown on the display while
[VIB] is selected.
: Alert by vibration.
:
Alert by tone and fl ashing display
illumination.
●
To return to the Timekeeping Mode, press
4
A
.
To test vibration ◆
●
In the Timekeeping Mode, hold down
B
to perform the vibration operation.
Vibration indicator
E-44
●
To return to the Timekeeping Mode, press
4
A
.
Note
The above procedure affects the button operation tone only. The alarm, hourly time
signal, and time up alarm are not affected.
To change the alarm/timer alert method
●
In the Timekeeping Mode, hold down
1
A
for about
two seconds until the time zone setting screen
appears.
1
●
Press
2
C
11 times to display alert setting screen.
See “Confi guring Current Time and Date Settings”
(page E-15).
The screen will show either [VIB] or [FLASH].
E-43
●
Press
2
C
nine times to display the button
operation tone setting screen.
See “Confi guring Current Time and Date Settings”
(page E-15).
The screen will show either [KEY
] or [MUTE].
MUTE indicator
●
Press
3
D
to toggle the setting between
[KEY
] (ON) and [MUTE] (OFF).
When [MUTE] (OFF) is selected, a MUTE indicator is
displayed to indicate that the button operation tone
will not sound.
E-42
Other Settings
You can use the procedures in this section to turn the tone that sounds when you
press a button on or off.
You can also select either tone and display illumination fl ashing, or vibration as the
alert method for the alarm and timer.
To turn the button operation tone on or off
●
In the Timekeeping Mode, hold down
1
A
for about
two seconds until the time zone setting screen
appears.
E-41
Note
If a countdown was stopped part way through in the Timer Mode, the current x
(stopped) countdown time will be displayed when you press A in the Timekeeping
Mode.
While a countdown is in progress, the display will show the countdown. You can x
switch to display of the day of the week and day by pressing A.
To stop a tone/vibration alert operation
●
Pressing any one of the buttons will stop an ongoing tone/vibration alert
operation.
E-40
Note
If a previous countdown was stopped part way through in the Timer Mode, x
pressing D will resume the countdown.
The x D button will be disabled if a countdown that was started in the Timer Mode
is still in progress.
An ongoing countdown (started in either the Timer Mode or Timekeeping Mode) x
cannot be stopped or reset in the Timekeeping Mode.
To view the timer start time ◆
●
In the Timekeeping Mode, press
A
.
This will cause the timer start time (the start time you set with the procedure on
page E-36) to appear for one second in the display in place of the day of the
week and day.