User manual

Bruksanvisning 3403
6. När du har utfört alla önskade inställningar trycker du A för att lämna inställningsdisplayen.
7. För att återgå till Tidvisningsfunktionen, tryck C tre gånger.
Att stoppa en ljud-/vibrationssignal
■ Tryck på valfri knapp för att stoppa en pågående ljud-/vibrationssignal.
Att testa alarmet
■ I Alarmfunktionen, tryck och håll inne D för att testa ljud-/vibrationssignalen.
E-30
Att mäta tid med stoppuret
Nedan visas stoppurets knappfunktioner.
■ Föruten tid/ackumulerad tid
■ Mellantid (paused avläsning av föruten tid)
Om du trycker B medan tidtagningen pågår visas mellantiden ([SPLIT] blinkar) samtidigt som
tidtagningen fortsätter internt.
E-32
Timer
Timerns starttid kan ställas in i steg om en sekund upp till 24 timmar. Klockan ger en ljudsig-
nal och blinkar med displaybelysningen eller vibrerar när timerns nedräkning når noll.
Se ”Att ändra signalmetod for alarm/timer” (sida E-44).
Observera!
Du kan starta en timernedräkning medan klockan benner sig i Tidvisningsfunktionen.
Se ”Användning av Timern i Tidvisningsfunktionen” (sida E-39) för mer information.
E-34
Att ställa in timerns starttid
1. I Timerfunktionen, tryck och håll inne A i ca två sekunder.
[SET Hold] visas på displayen. Därefter försvinner [SET
Hold] och timsiffrorna blinkar.
Observera!
■ Om en timernedräkning pågår, tryck D för att stoppa den och
sedan B för nollställa timern till dess starttid innan ovanstående
steg utförs.
■ Om en timernedräkning är pausad trycker du B för nollställa
timern till dess starttid innan ovanstående steg utförs.
2. Använd C för att ytta blinkanket mellan timmar, minuter och sekunder.
De blinkande siffrorna är de som är valda.
E-36
Att utföra en nedräkning
■ Nedan visas knappfunktionerna för en nedräkning.
Observera!
■ En ljud-/vibrationssignal ges i ca 10 sekunder när nedräkningen når noll, och displayen
återgår till att visa innehållet som visades innan nedräkningen startades.
■ Även om du lämnar Timerfunktionen medan en timernedräkning pågår, kommer nedräk-
ningen att fortsätta och ljud-/vibrationssignalen ges när nedräkningen når noll.
■ En timerindikator blinkar medan nedräkningen pågår.
E-38
Stoppur
Stoppuret mäter tiden i 1/100-dels sekunder upp till 999 timmar, 59 minuter och 59,99 sek-
under. Den uppmätta tiden återgår automatiskt till noll och tidtagningen fortsätter därifrån när
stoppuret har nått maxgränsen.
Att gå till Stoppursfunktionen
■ I Tidvisningsfunktionen, tryck C tre gånger för att gå till
Stoppursfunktionen.
Se ”Funktionslägen” (sida E-12).
[STW] visas på displayen i ca en sekund, och sedan visas
stoppursdisplayen.
E-31
Observera!
■ När tidtagningen har startats fortsätter den tills du trycker D för att stoppa den, även om du
växlar till en annan funktion eller om stoppuret når maxgränsen.
■ Om du växlar till en annan funktion medan mellantiden visas på displayen kommer visningen
av mellantiden att avbrytas.
E-33
Att gå till Timerfunktionen
■ I Tidvisningsfunktionen, tryck C fyra gånger för att gå till
Timerfunktionen.
Se ”Funktionslägen” (sida E-12).
E-35
3. Använd B och D för att ändra den för tillfället valda inställningen (timmar, minuter
eller sekunder).
■ Tryck och håll inne någon av knapparna för att scrolla inställningen med hög hastighet.
■ För att ange en starttid på 24 timmar, ställ in timern på 0H 00’00”.
4. När du har utfört alla önskade inställningar trycker du A för att lämna
inställningsdisplayen.
E-37
Användning av Timern i Tidvisningsfunktionen
◊ Att starta en timernedräkning
■ I Tidvisningsfunktionen, tryck D.
Detta får displayen för veckodagen och datumet att ändras till en timerdisplay.
E-39
Operation Guide 3403
E-39
Using the Timer in the Timekeeping Mode
To start a timer countdown ◆
●
In the Timekeeping Mode, press
D
.
This will cause the day of the week and day display to change to a timer display.
Timer indicator
Timer
D
E-38
To perform a countdown
●
The following shows button operations for a countdown.
D
D D D B
Start Stop (Restart) (Stop) Reset
Note
A tone/vibration alert is performed for about 10 seconds when the end of the x
countdown is reached, and the display returns to the screen that was shown
before the countdown was started.
Even if you exit the Timer Mode while a timer countdown is ongoing, the x
countdown will continue and the tone/vibration alert operation will be performed
when the end of the countdown is reached.
A timer indicator fl ashes while a countdown operation is in progress. x
E-37
●
Use
3
B
and
D
to change the currently selected setting (hours, minutes, or
seconds).
Holding down either button scrolls the setting at high speed. x
To specify a start time of 24 hours, set the timer to 0H 00'00". x
●
After all the settings are the way you want, press
4
A
to exit the setting
screen.
E-36
To set the timer start time
●
In the Timer Mode, hold down
1
A
for about two seconds.
[SET Hold] will appear on the display. After that, [SET
Hold] will disappear and the hours digits will fl ash.
Note
If a timer countdown operation is in progress, press x
D to stop it and then press B to reset the timer to
its start time before performing the above step.
If a timer countdown operation is paused, press x B
to reset the timer to its start time before performing
the above step.
●
Use
2
C
to move the fl ashing between the hours, minutes, and seconds.
The fl ashing digits are the ones that are selected.
E-35
To enter the Timer Mode
●
In the Timekeeping Mode, press
C
four
times to enter the Timer Mode.
See “Using Modes” (page E-12).
Seconds
Minutes 1/10 second
Hours
Current time
E-34
Timer
The timer start time can be set in one-second increments up to 24 hours. The watch
will sound a tone and fl ash its display illumination, or it will vibrate when the end of
the timer countdown is reached.
See “To change the alarm/timer alert method” (page E-44).
Note
You can start a timer countdown operation while in the Timekeeping Mode.
See “Using the Timer in the Timekeeping Mode” (page E-39) for more information.
E-33
Note
Once started, elapsed time measurement continues until you press x D to stop
it, even if you change to a different mode and even if the stopwatch reaches the
elapsed time measurement limit.
If you change to another mode while a split time is frozen on the display, split time x
display will be canceled.
E-32
To measure time with the stopwatch
●
The following shows button operations for stopwatch operations.
Elapsed time/cumulative time x
D D D D B
Start Stop (Restart) (Stop) Reset
Split time (paused elapsed time reading) x
D B B D B
Start Split Split time display
cancel
Stop Reset
Pressing B while timing is being performed displays the split time (with [SPLIT]
fl ashing), but elapsed timing continues internally.
E-31
Stopwatch
The stopwatch measures elapsed time in units of 1/100 seconds up to 999 hours,
59 minutes, 59.99 seconds. Elapsed time returns to zero automatically and timing
continues from there when the maximum limit is reached.
To enter the Stopwatch Mode
●
In the Timekeeping Mode, press C three
times to enter the Stopwatch Mode.
See “Using Modes” (page E-12).
[STW] will appear on the display for about
one second, and then the stopwatch screen
will appear.
Seconds
Minutes 1/100 second
Hours
Current time
E-30
●
After all the settings are the way you want, press
6
A
to exit the setting
screen.
●
To return to the Timekeeping Mode, press
7
C
three times.
To stop a tone/vibration alert operation
●
Pressing any one of the buttons will stop an ongoing tone/vibration alert
operation.
To test the alarm
●
In the Alarm Mode, hold down
D
to perform the tone/vibration alert
operations.
Operation Guide 3403
E-39
Using the Timer in the Timekeeping Mode
To start a timer countdown ◆
●
In the Timekeeping Mode, press
D
.
This will cause the day of the week and day display to change to a timer display.
Timer indicator
Timer
D
E-38
To perform a countdown
●
The following shows button operations for a countdown.
D
D D D B
Start Stop (Restart) (Stop) Reset
Note
A tone/vibration alert is performed for about 10 seconds when the end of the x
countdown is reached, and the display returns to the screen that was shown
before the countdown was started.
Even if you exit the Timer Mode while a timer countdown is ongoing, the x
countdown will continue and the tone/vibration alert operation will be performed
when the end of the countdown is reached.
A timer indicator fl ashes while a countdown operation is in progress. x
E-37
●
Use
3
B
and
D
to change the currently selected setting (hours, minutes, or
seconds).
Holding down either button scrolls the setting at high speed. x
To specify a start time of 24 hours, set the timer to 0H 00'00". x
●
After all the settings are the way you want, press
4
A
to exit the setting
screen.
E-36
To set the timer start time
●
In the Timer Mode, hold down
1
A
for about two seconds.
[SET Hold] will appear on the display. After that, [SET
Hold] will disappear and the hours digits will fl ash.
Note
If a timer countdown operation is in progress, press x
D to stop it and then press B to reset the timer to
its start time before performing the above step.
If a timer countdown operation is paused, press x B
to reset the timer to its start time before performing
the above step.
●
Use
2
C
to move the fl ashing between the hours, minutes, and seconds.
The fl ashing digits are the ones that are selected.
E-35
To enter the Timer Mode
●
In the Timekeeping Mode, press
C
four
times to enter the Timer Mode.
See “Using Modes” (page E-12).
Seconds
Minutes 1/10 second
Hours
Current time
E-34
Timer
The timer start time can be set in one-second increments up to 24 hours. The watch
will sound a tone and fl ash its display illumination, or it will vibrate when the end of
the timer countdown is reached.
See “To change the alarm/timer alert method” (page E-44).
Note
You can start a timer countdown operation while in the Timekeeping Mode.
See “Using the Timer in the Timekeeping Mode” (page E-39) for more information.
E-33
Note
Once started, elapsed time measurement continues until you press x D to stop
it, even if you change to a different mode and even if the stopwatch reaches the
elapsed time measurement limit.
If you change to another mode while a split time is frozen on the display, split time x
display will be canceled.
E-32
To measure time with the stopwatch
●
The following shows button operations for stopwatch operations.
Elapsed time/cumulative time x
D D D D B
Start Stop (Restart) (Stop) Reset
Split time (paused elapsed time reading) x
D B B D B
Start Split Split time display
cancel
Stop Reset
Pressing B while timing is being performed displays the split time (with [SPLIT]
fl ashing), but elapsed timing continues internally.
E-31
Stopwatch
The stopwatch measures elapsed time in units of 1/100 seconds up to 999 hours,
59 minutes, 59.99 seconds. Elapsed time returns to zero automatically and timing
continues from there when the maximum limit is reached.
To enter the Stopwatch Mode
●
In the Timekeeping Mode, press
C
three
times to enter the Stopwatch Mode.
See “Using Modes” (page E-12).
[STW] will appear on the display for about
one second, and then the stopwatch screen
will appear.
Seconds
Minutes 1/100 second
Hours
Current time
E-30
●
After all the settings are the way you want, press
6
A
to exit the setting
screen.
●
To return to the Timekeeping Mode, press
7
C
three times.
To stop a tone/vibration alert operation
●
Pressing any one of the buttons will stop an ongoing tone/vibration alert
operation.
To test the alarm
●
In the Alarm Mode, hold down
D
to perform the tone/vibration alert
operations.
Operation Guide 3403
E-39
Using the Timer in the Timekeeping Mode
To start a timer countdown ◆
●
In the Timekeeping Mode, press
D
.
This will cause the day of the week and day display to change to a timer display.
Timer indicator
Timer
D
E-38
To perform a countdown
●
The following shows button operations for a countdown.
D
D D D B
Start Stop (Restart) (Stop) Reset
Note
A tone/vibration alert is performed for about 10 seconds when the end of the x
countdown is reached, and the display returns to the screen that was shown
before the countdown was started.
Even if you exit the Timer Mode while a timer countdown is ongoing, the x
countdown will continue and the tone/vibration alert operation will be performed
when the end of the countdown is reached.
A timer indicator fl ashes while a countdown operation is in progress. x
E-37
●
Use
3
B
and
D
to change the currently selected setting (hours, minutes, or
seconds).
Holding down either button scrolls the setting at high speed. x
To specify a start time of 24 hours, set the timer to 0H 00'00". x
●
After all the settings are the way you want, press
4
A
to exit the setting
screen.
E-36
To set the timer start time
●
In the Timer Mode, hold down
1
A
for about two seconds.
[SET Hold] will appear on the display. After that, [SET
Hold] will disappear and the hours digits will fl ash.
Note
If a timer countdown operation is in progress, press x
D to stop it and then press B to reset the timer to
its start time before performing the above step.
If a timer countdown operation is paused, press x B
to reset the timer to its start time before performing
the above step.
●
Use
2
C
to move the fl ashing between the hours, minutes, and seconds.
The fl ashing digits are the ones that are selected.
E-35
To enter the Timer Mode
●
In the Timekeeping Mode, press
C
four
times to enter the Timer Mode.
See “Using Modes” (page E-12).
Seconds
Minutes 1/10 second
Hours
Current time
E-34
Timer
The timer start time can be set in one-second increments up to 24 hours. The watch
will sound a tone and fl ash its display illumination, or it will vibrate when the end of
the timer countdown is reached.
See “To change the alarm/timer alert method” (page E-44).
Note
You can start a timer countdown operation while in the Timekeeping Mode.
See “Using the Timer in the Timekeeping Mode” (page E-39) for more information.
E-33
Note
Once started, elapsed time measurement continues until you press x D to stop
it, even if you change to a different mode and even if the stopwatch reaches the
elapsed time measurement limit.
If you change to another mode while a split time is frozen on the display, split time x
display will be canceled.
E-32
To measure time with the stopwatch
●
The following shows button operations for stopwatch operations.
Elapsed time/cumulative time x
D D D D B
Start Stop (Restart) (Stop) Reset
Split time (paused elapsed time reading) x
D B B D B
Start Split Split time display
cancel
Stop Reset
Pressing B while timing is being performed displays the split time (with [SPLIT]
fl ashing), but elapsed timing continues internally.
E-31
Stopwatch
The stopwatch measures elapsed time in units of 1/100 seconds up to 999 hours,
59 minutes, 59.99 seconds. Elapsed time returns to zero automatically and timing
continues from there when the maximum limit is reached.
To enter the Stopwatch Mode
●
In the Timekeeping Mode, press
C
three
times to enter the Stopwatch Mode.
See “Using Modes” (page E-12).
[STW] will appear on the display for about
one second, and then the stopwatch screen
will appear.
Seconds
Minutes 1/100 second
Hours
Current time
E-30
●
After all the settings are the way you want, press
6
A
to exit the setting
screen.
●
To return to the Timekeeping Mode, press
7
C
three times.
To stop a tone/vibration alert operation
●
Pressing any one of the buttons will stop an ongoing tone/vibration alert
operation.
To test the alarm
●
In the Alarm Mode, hold down
D
to perform the tone/vibration alert
operations.
Operation Guide 3403
E-39
Using the Timer in the Timekeeping Mode
To start a timer countdown ◆
●
In the Timekeeping Mode, press
D
.
This will cause the day of the week and day display to change to a timer display.
Timer indicator
Timer
D
E-38
To perform a countdown
●
The following shows button operations for a countdown.
D
D D D B
Start Stop (Restart) (Stop) Reset
Note
A tone/vibration alert is performed for about 10 seconds when the end of the x
countdown is reached, and the display returns to the screen that was shown
before the countdown was started.
Even if you exit the Timer Mode while a timer countdown is ongoing, the x
countdown will continue and the tone/vibration alert operation will be performed
when the end of the countdown is reached.
A timer indicator fl ashes while a countdown operation is in progress. x
E-37
●
Use
3
B
and
D
to change the currently selected setting (hours, minutes, or
seconds).
Holding down either button scrolls the setting at high speed. x
To specify a start time of 24 hours, set the timer to 0H 00'00". x
●
After all the settings are the way you want, press
4
A
to exit the setting
screen.
E-36
To set the timer start time
●
In the Timer Mode, hold down
1
A
for about two seconds.
[SET Hold] will appear on the display. After that, [SET
Hold] will disappear and the hours digits will fl ash.
Note
If a timer countdown operation is in progress, press x
D to stop it and then press B to reset the timer to
its start time before performing the above step.
If a timer countdown operation is paused, press x B
to reset the timer to its start time before performing
the above step.
●
Use
2
C
to move the fl ashing between the hours, minutes, and seconds.
The fl ashing digits are the ones that are selected.
E-35
To enter the Timer Mode
●
In the Timekeeping Mode, press C four
times to enter the Timer Mode.
See “Using Modes” (page E-12).
Seconds
Minutes 1/10 second
Hours
Current time
E-34
Timer
The timer start time can be set in one-second increments up to 24 hours. The watch
will sound a tone and fl ash its display illumination, or it will vibrate when the end of
the timer countdown is reached.
See “To change the alarm/timer alert method” (page E-44).
Note
You can start a timer countdown operation while in the Timekeeping Mode.
See “Using the Timer in the Timekeeping Mode” (page E-39) for more information.
E-33
Note
Once started, elapsed time measurement continues until you press x D to stop
it, even if you change to a different mode and even if the stopwatch reaches the
elapsed time measurement limit.
If you change to another mode while a split time is frozen on the display, split time x
display will be canceled.
E-32
To measure time with the stopwatch
●
The following shows button operations for stopwatch operations.
Elapsed time/cumulative time x
D D D D B
Start Stop (Restart) (Stop) Reset
Split time (paused elapsed time reading) x
D B B D B
Start Split Split time display
cancel
Stop Reset
Pressing B while timing is being performed displays the split time (with [SPLIT]
fl ashing), but elapsed timing continues internally.
E-31
Stopwatch
The stopwatch measures elapsed time in units of 1/100 seconds up to 999 hours,
59 minutes, 59.99 seconds. Elapsed time returns to zero automatically and timing
continues from there when the maximum limit is reached.
To enter the Stopwatch Mode
●
In the Timekeeping Mode, press
C
three
times to enter the Stopwatch Mode.
See “Using Modes” (page E-12).
[STW] will appear on the display for about
one second, and then the stopwatch screen
will appear.
Seconds
Minutes 1/100 second
Hours
Current time
E-30
●
After all the settings are the way you want, press
6
A
to exit the setting
screen.
●
To return to the Timekeeping Mode, press
7
C
three times.
To stop a tone/vibration alert operation
●
Pressing any one of the buttons will stop an ongoing tone/vibration alert
operation.
To test the alarm
●
In the Alarm Mode, hold down
D
to perform the tone/vibration alert
operations.
Operation Guide 3403
E-39
Using the Timer in the Timekeeping Mode
To start a timer countdown ◆
●
In the Timekeeping Mode, press
D
.
This will cause the day of the week and day display to change to a timer display.
Timer indicator
Timer
D
E-38
To perform a countdown
●
The following shows button operations for a countdown.
D
D D D B
Start Stop (Restart) (Stop) Reset
Note
A tone/vibration alert is performed for about 10 seconds when the end of the x
countdown is reached, and the display returns to the screen that was shown
before the countdown was started.
Even if you exit the Timer Mode while a timer countdown is ongoing, the x
countdown will continue and the tone/vibration alert operation will be performed
when the end of the countdown is reached.
A timer indicator fl ashes while a countdown operation is in progress. x
E-37
●
Use
3
B
and
D
to change the currently selected setting (hours, minutes, or
seconds).
Holding down either button scrolls the setting at high speed. x
To specify a start time of 24 hours, set the timer to 0H 00'00". x
●
After all the settings are the way you want, press
4
A
to exit the setting
screen.
E-36
To set the timer start time
●
In the Timer Mode, hold down
1
A for about two seconds.
[SET Hold] will appear on the display. After that, [SET
Hold] will disappear and the hours digits will fl ash.
Note
If a timer countdown operation is in progress, press x
D to stop it and then press B to reset the timer to
its start time before performing the above step.
If a timer countdown operation is paused, press x B
to reset the timer to its start time before performing
the above step.
●
Use
2
C to move the fl ashing between the hours, minutes, and seconds.
The fl ashing digits are the ones that are selected.
E-35
To enter the Timer Mode
●
In the Timekeeping Mode, press
C
four
times to enter the Timer Mode.
See “Using Modes” (page E-12).
Seconds
Minutes 1/10 second
Hours
Current time
E-34
Timer
The timer start time can be set in one-second increments up to 24 hours. The watch
will sound a tone and fl ash its display illumination, or it will vibrate when the end of
the timer countdown is reached.
See “To change the alarm/timer alert method” (page E-44).
Note
You can start a timer countdown operation while in the Timekeeping Mode.
See “Using the Timer in the Timekeeping Mode” (page E-39) for more information.
E-33
Note
Once started, elapsed time measurement continues until you press x D to stop
it, even if you change to a different mode and even if the stopwatch reaches the
elapsed time measurement limit.
If you change to another mode while a split time is frozen on the display, split time x
display will be canceled.
E-32
To measure time with the stopwatch
●
The following shows button operations for stopwatch operations.
Elapsed time/cumulative time x
D D D D B
Start Stop (Restart) (Stop) Reset
Split time (paused elapsed time reading) x
D B B D B
Start Split Split time display
cancel
Stop Reset
Pressing B while timing is being performed displays the split time (with [SPLIT]
fl ashing), but elapsed timing continues internally.
E-31
Stopwatch
The stopwatch measures elapsed time in units of 1/100 seconds up to 999 hours,
59 minutes, 59.99 seconds. Elapsed time returns to zero automatically and timing
continues from there when the maximum limit is reached.
To enter the Stopwatch Mode
●
In the Timekeeping Mode, press
C
three
times to enter the Stopwatch Mode.
See “Using Modes” (page E-12).
[STW] will appear on the display for about
one second, and then the stopwatch screen
will appear.
Seconds
Minutes 1/100 second
Hours
Current time
E-30
●
After all the settings are the way you want, press
6
A
to exit the setting
screen.
●
To return to the Timekeeping Mode, press
7
C
three times.
To stop a tone/vibration alert operation
●
Pressing any one of the buttons will stop an ongoing tone/vibration alert
operation.
To test the alarm
●
In the Alarm Mode, hold down
D
to perform the tone/vibration alert
operations.
Operation Guide 3403
E-39
Using the Timer in the Timekeeping Mode
To start a timer countdown ◆
●
In the Timekeeping Mode, press
D
.
This will cause the day of the week and day display to change to a timer display.
Timer indicator
Timer
D
E-38
To perform a countdown
●
The following shows button operations for a countdown.
D
D D D B
Start Stop (Restart) (Stop) Reset
Note
A tone/vibration alert is performed for about 10 seconds when the end of the x
countdown is reached, and the display returns to the screen that was shown
before the countdown was started.
Even if you exit the Timer Mode while a timer countdown is ongoing, the x
countdown will continue and the tone/vibration alert operation will be performed
when the end of the countdown is reached.
A timer indicator fl ashes while a countdown operation is in progress. x
E-37
●
Use
3
B
and
D
to change the currently selected setting (hours, minutes, or
seconds).
Holding down either button scrolls the setting at high speed. x
To specify a start time of 24 hours, set the timer to 0H 00'00". x
●
After all the settings are the way you want, press
4
A
to exit the setting
screen.
E-36
To set the timer start time
●
In the Timer Mode, hold down
1
A
for about two seconds.
[SET Hold] will appear on the display. After that, [SET
Hold] will disappear and the hours digits will fl ash.
Note
If a timer countdown operation is in progress, press x
D to stop it and then press B to reset the timer to
its start time before performing the above step.
If a timer countdown operation is paused, press x B
to reset the timer to its start time before performing
the above step.
●
Use
2
C
to move the fl ashing between the hours, minutes, and seconds.
The fl ashing digits are the ones that are selected.
E-35
To enter the Timer Mode
●
In the Timekeeping Mode, press
C
four
times to enter the Timer Mode.
See “Using Modes” (page E-12).
Seconds
Minutes 1/10 second
Hours
Current time
E-34
Timer
The timer start time can be set in one-second increments up to 24 hours. The watch
will sound a tone and fl ash its display illumination, or it will vibrate when the end of
the timer countdown is reached.
See “To change the alarm/timer alert method” (page E-44).
Note
You can start a timer countdown operation while in the Timekeeping Mode.
See “Using the Timer in the Timekeeping Mode” (page E-39) for more information.
E-33
Note
Once started, elapsed time measurement continues until you press x D to stop
it, even if you change to a different mode and even if the stopwatch reaches the
elapsed time measurement limit.
If you change to another mode while a split time is frozen on the display, split time x
display will be canceled.
E-32
To measure time with the stopwatch
●
The following shows button operations for stopwatch operations.
Elapsed time/cumulative time x
D D D D B
Start Stop (Restart) (Stop) Reset
Split time (paused elapsed time reading) x
D B B D B
Start Split Split time display
cancel
Stop Reset
Pressing B while timing is being performed displays the split time (with [SPLIT]
fl ashing), but elapsed timing continues internally.
E-31
Stopwatch
The stopwatch measures elapsed time in units of 1/100 seconds up to 999 hours,
59 minutes, 59.99 seconds. Elapsed time returns to zero automatically and timing
continues from there when the maximum limit is reached.
To enter the Stopwatch Mode
●
In the Timekeeping Mode, press
C
three
times to enter the Stopwatch Mode.
See “Using Modes” (page E-12).
[STW] will appear on the display for about
one second, and then the stopwatch screen
will appear.
Seconds
Minutes 1/100 second
Hours
Current time
E-30
●
After all the settings are the way you want, press
6
A
to exit the setting
screen.
●
To return to the Timekeeping Mode, press
7
C
three times.
To stop a tone/vibration alert operation
●
Pressing any one of the buttons will stop an ongoing tone/vibration alert
operation.
To test the alarm
●
In the Alarm Mode, hold down
D
to perform the tone/vibration alert
operations.
Operation Guide 3403
E-39
Using the Timer in the Timekeeping Mode
To start a timer countdown ◆
●
In the Timekeeping Mode, press
D
.
This will cause the day of the week and day display to change to a timer display.
Timer indicator
Timer
D
E-38
To perform a countdown
●
The following shows button operations for a countdown.
D
D D D B
Start Stop (Restart) (Stop) Reset
Note
A tone/vibration alert is performed for about 10 seconds when the end of the x
countdown is reached, and the display returns to the screen that was shown
before the countdown was started.
Even if you exit the Timer Mode while a timer countdown is ongoing, the x
countdown will continue and the tone/vibration alert operation will be performed
when the end of the countdown is reached.
A timer indicator fl ashes while a countdown operation is in progress. x
E-37
●
Use
3
B
and
D
to change the currently selected setting (hours, minutes, or
seconds).
Holding down either button scrolls the setting at high speed. x
To specify a start time of 24 hours, set the timer to 0H 00'00". x
●
After all the settings are the way you want, press
4
A
to exit the setting
screen.
E-36
To set the timer start time
●
In the Timer Mode, hold down
1
A
for about two seconds.
[SET Hold] will appear on the display. After that, [SET
Hold] will disappear and the hours digits will fl ash.
Note
If a timer countdown operation is in progress, press x
D to stop it and then press B to reset the timer to
its start time before performing the above step.
If a timer countdown operation is paused, press x B
to reset the timer to its start time before performing
the above step.
●
Use
2
C
to move the fl ashing between the hours, minutes, and seconds.
The fl ashing digits are the ones that are selected.
E-35
To enter the Timer Mode
●
In the Timekeeping Mode, press
C
four
times to enter the Timer Mode.
See “Using Modes” (page E-12).
Seconds
Minutes 1/10 second
Hours
Current time
E-34
Timer
The timer start time can be set in one-second increments up to 24 hours. The watch
will sound a tone and fl ash its display illumination, or it will vibrate when the end of
the timer countdown is reached.
See “To change the alarm/timer alert method” (page E-44).
Note
You can start a timer countdown operation while in the Timekeeping Mode.
See “Using the Timer in the Timekeeping Mode” (page E-39) for more information.
E-33
Note
Once started, elapsed time measurement continues until you press x D to stop
it, even if you change to a different mode and even if the stopwatch reaches the
elapsed time measurement limit.
If you change to another mode while a split time is frozen on the display, split time x
display will be canceled.
E-32
To measure time with the stopwatch
●
The following shows button operations for stopwatch operations.
Elapsed time/cumulative time x
D D D D B
Start Stop (Restart) (Stop) Reset
Split time (paused elapsed time reading) x
D B B D B
Start Split Split time display
cancel
Stop Reset
Pressing B while timing is being performed displays the split time (with [SPLIT]
fl ashing), but elapsed timing continues internally.
E-31
Stopwatch
The stopwatch measures elapsed time in units of 1/100 seconds up to 999 hours,
59 minutes, 59.99 seconds. Elapsed time returns to zero automatically and timing
continues from there when the maximum limit is reached.
To enter the Stopwatch Mode
●
In the Timekeeping Mode, press
C
three
times to enter the Stopwatch Mode.
See “Using Modes” (page E-12).
[STW] will appear on the display for about
one second, and then the stopwatch screen
will appear.
Seconds
Minutes 1/100 second
Hours
Current time
E-30
●
After all the settings are the way you want, press
6
A
to exit the setting
screen.
●
To return to the Timekeeping Mode, press
7
C
three times.
To stop a tone/vibration alert operation
●
Pressing any one of the buttons will stop an ongoing tone/vibration alert
operation.
To test the alarm
●
In the Alarm Mode, hold down
D
to perform the tone/vibration alert
operations.