User manual

Operation Guide 2787
1
About This Manual
• Button operations are indicated using the letters shown
in the illustration.
• Most of the display examples in this manual show only
the digital display, without the analog hands, as shown
in the lower illustration.
• Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference” section.
Press .
Timekeeping Mode World Time 1 Mode World Time 2 Mode Alarm Mode Stopwatch Mode Hand Setting Mode
Animation area
General Guide
• Press C to change from mode to mode.
• In any mode, press B to illuminate the display.
Timekeeping
This watch features separate digital and analog timekeeping. The procedures for
setting the digital time and analog time are different.
• In the Timekeeping Mode, you can press D to change the display format as shown
below.
World time hands
Month – Day Animation area (Seconds)
Day of week
Day
PM indicator
Hour : Minutes
Day Seconds
World Time
1 city code
World Time 2 city code
Press .
• After the seconds count reaches 30, various animations play for about two seconds
in the animation area.
• The World Time hands show the hour in the cities selected for World Time 1 and
World Time 2. See “World Time Hands” for more information.
Digital Time and Date
Use the Timekeeping Mode to set and view a digital display of the current time and date.
When setting the digital time, you can also configure settings for the display
illumination duration, summer time (Daylight Saving time or DST), your Home City
code (the code for the city where you normally use the watch), and the 12/24-hour
format.
• This watch is preset with a number of city codes, each of which represents the time
zone where that city is located. When setting the digital time, it is important that you
select the correct city code for your Home City. If your location is not included in the
preset city codes, select the preset city code that is in the same time zone as your
location.
• Note that all of the times for the World Time Mode city codes are displayed in
accordance with the digital time and date settings you configure in the Timekeeping
Mode.
• After you correctly set your Home City time and date, you can set the watch up for
timekeeping with a different city code simply by changing the Home City code in the
Timekeeping Mode.
To set the digital time and date
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C twice to move the flashing to the Home City
code setting (see the illustration below), and then use
B and D to select the code you want.
• Make sure you select your Home City code before
changing any other setting.
• For full information on city codes, see the “City Code
Table”.
3. Press C to move the flashing in the sequence shown below to select the other settings.
Seconds DST Home City Code Hour Minutes
Day Month Year 12/24-Hour Format
5. Press A to exit the setting screen.
• Resetting the seconds only (without changing the DST, Home City code, hour, or
minute setting) causes the analog minute hand setting to be adjusted automatically.
• See “Digital Time Daylight Saving Time (DST) Setting” below for details about the
DST setting.
• The day of the week is automatically displayed in accordance with the date (year,
month, and day) settings.
Digital Time Daylight Saving Time (DST) Setting
Daylight Saving Time (summer time) advances the digital time setting by one hour
from Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To toggle the Timekeeping Mode digital time between DST and Standard Time
1. In the Timekeeping Mode, hold down A until the seconds
start to flash, which indicates the setting screen.
2. Press C once to display the DST setting screen.
3. Press D to toggle between Daylight Saving Time (
ON
displayed) and Standard Time (OFF displayed).
4. Press A to exit the setting screen.
• The DST indicator appears on the Timekeeping and
Alarm Mode displays to indicate that Daylight Saving
Time is turned on.
DST indicator
Setting the Analog Time
Perform the procedure below when the time indicated by the analog hands does not
match the time of the digital display.
To adjust the analog time
1. In the Timekeeping Mode, press C five times to enter
the Hand Setting Mode.
2. Hold down A until the current digital time starts to
flash, which indicates the analog time setting screen.
3. Press D to advance the analog time setting by
20 seconds.
• Adjust the analog time so it matches the digital time.
• Holding down D advances the analog time setting at
high speed.
Hour hand Minute hand
• If you need to advance the analog time setting a long way, hold down D until the
time starts advancing at high speed, and then press B. This locks the high-
speed hand movement, so you can release the two buttons. High-speed hand
movement continues until you press any button. It will also stop automatically
after the time advances 12 hours or if an alarm (Daily Alarm or Hourly Time
Signal) starts to sound.
4. Press A to exit the setting screen.
• The watch will automatically adjust the minute hand slightly to match its internal
second count when you exit the setting screen.
• To return to the Timekeeping Mode, press C.
4. When the setting you want to change is flashing, use B and D to change it as
described below.
Screen
OFF
TYO
BCH
CAA@
To do this:
Reset the seconds to AA
Toggle the display illumination duration setting
between 1.5 second ( ) and 2.5 seconds ( )
Toggle between Daylight Saving Time (ON)
and Standard Time (OFF)
Change the Home City code
Change the hour or minutes
Toggle between 12-hour (BCH) and 24-hour
(C@H) timekeeping
Change the year
Change the month or day
Do this:
Press D.
Press B while the seconds
count is flashing.
Press D.
Use D (east) and B (west).
Use D (+) and B (–).
Press D.
Use D (+) and B (–).
• The animation area shows different animated characters, depending on the mode
and the operation being performed.
MA0311-EA