User manual

ManualsBrandsCasio ManualsWatch2736

Operation Guide 2736

Alarm Mode

Using the Alarms

❚

Alarm Types

This watch has five alarms: three daily alarms, one target alarm,

and one snooze alarm.

Daily Alarm (AL1, AL2, AL3)

The watch beeps for 10 seconds when the alarm time is

reached.

Target Alarm (TAL)

The watch beeps for 10 seconds when the alarm time is

reached.

• With a target alarm, the time remaining until the alarm time

counts down on the display.

Snooze Alarm (SNZ)

With the snooze alarm, the watch beeps for 10 seconds when

the alarm time is reached, and up to seven times at five-

minute intervals thereafter. Pressing any button stops the

beeper, but the alarm will sound again after five minutes.

❚

To view an alarm time

In the Alarm Mode, press the

D button.

• Each press of the D button

cycles through available modes in

the sequence shown below.

Alarm 1

(AL1)

Alarm 2

(AL2)

Alarm 3

(AL3)

Hourly Time

Signal (SIG)

Snooze Alarm

(SNZ)

Target Alarm

(TAL)

About the Target Alarm Screen

If the target alarm (TAL) is turned

on, the alarm time appears first,

followed by a screen that shows how

much time remains until the alarm

time is reached (target alarm time).

Alarm Type

Alarm Time

Remaining Time

❚

To set an alarm

1. In the Alarm Mode, use

the

D button to scroll

through the alarm

screens (AL1 to AL5) until

the one you want is

displayed.

2. Hold down the

A button

for about two seconds

until the hour digits of the

alarm time start to flash.

• This is the setting screen.

Displaying the setting

automatically turns on the

alarm.

3. Use the

D (+) and

B (–)

buttons to change the

hour setting.

• Holding down either button

changes the setting at high

speed.

• When setting the hour, make sure you specify AM (no

indicator) or PM (P) correctly when using 12-hour

timekeeping, or that you specify the correct 24-hour time.

• The same 12-hour/24-hour format you select for the

Timekeeping Mode time is also applied in the Alarm Mode.

4. Press the

C button to

move the flashing to the

minute digits.

5. As with the hour setting,

use the

D (+) and

B (–)

buttons to change the

minute setting.

• Each press of the C button

moves the flashing between

the hour digits and the minute

digits as shown below.

Hour

Minute

6. When the setting is the

way you want, press the

A button.

• This exits the setting screen.

• The display also will exit the setting screen automatically if

you do not perform any operation for about two or three

minutes.

Hour

Alarm Indicator

(Forward)

(Back)

(Forward)

(Back)

Minute

❚

To turn an alarm time on or off

1. In the Alarm Mode, use

the

D button to display

the screen for the alarm

you want to turn on or off.

2. Press the

A button to

toggle the displayed

alarm on reception on or

off.

• Turning on an alarm causes the alarm indicator (ALM) to

appear on its screen. The snooze alarm screen also has a

snooze indicator (SNZ).

Alarm 1 Screen

Alarm Indicator

Snooze Alarm Screen

Snooze Indicator

Alarm Indicator

❚

To stop the alarm beeper

Pressing any button while the beeper is sounding stops it.

• In the case of the snooze alarm the alarm will sound again. The

snooze indicator flashes while the snooze alarm is active

(indicating that the alarm will sound again).

• Use the procedure under “To turn an alarm on or off” to turn off

the snooze alarm so it does not sound any more.

Important!

Performing any of the following operations while the snooze

indicator is flashing on the display cancels the snooze operation

and stops the flashing.

• Displaying the Timekeeping Mode setting screen

• Displaying the Alarm Mode (snooze alarm) setting screen

❚

To test the alarm

In the Alarm Mode, hold down the D button to sound the alarm.

Using the Hourly Time Signal

The hourly time signal causes the watch to beep every hour on the

hour.

❚

To turn the hourly time signal on or off

1. In the Alarm Mode, use

the

D button to display

the screen for the hourly

time signal (SIG).

2. Press the

A button to

toggle the hourly time

signal on or off.

• Tu rning on the hourly time signal causes its indicator (SIG)

to appear on the screen.

Hourly Time Signal Screen

Hourly Time

Signal Indicator