User manual

USER’S GUIDE 2618
3
To input the password
1. Enter the e-DATA MEMORY Mode.
2. On the Password Input screen (
PA55), press
D. This causes the first digit of the password to flash.
3. Input the password.
• Input the password you registered or
0000
.
• Use D (+) to scroll through numbers at each digit.
• Press C to advance to the next digit.
4. After the password is the way you want, press C.
• If the input password matches the one registered, the
word
OK!
appears, followed by an e-DATA MEMORY
screen.
• If the password does not match, the word
ERROR
appears, followed by the Password Input screen.
• If you want to be able to access e-DATA MEMORY
without inputting a password, delete the password using
the procedure under “To delete the password”.
• If you make a mistake part way through inputting the
password, press C to scroll past the remaining digits.
This will cause a password input error, after which you
can re-input the password.
To change the password
1. Enter the e-DATA MEMORY Mode by inputting the current password.
2. Use D (+) and B (–) to display the Password Setting screen.
3. Perform the procedure starting from step 2 under “To register a new password” to
specify the new password.
To delete the password
1. Enter the e-DATA MEMORY Mode by inputting the current password.
2. Use D (+) and B (–) to display the Password Setting screen.
3. Hold down A for about two seconds until the first (leftmost) digit of the password
starts to flash.
4. Press B and D at the same time to delete the password.
• The word
CLEAR appears to indicate that the password is being deleted. After the
password is deleted, the Password Setting screen appears.
Alarms
You can set five independent Daily Alarms. When an alarm is turned on, the alarm
tone sounds when the alarm time is reached. One of the alarms is a snooze alarm,
while the other four are one-time alarms. You can also input reminder text.
You can turn on an Hourly Time Signal that causes the watch to beep twice every hour
on the hour.
Note
• Use the Alarm Mode to configure one-time alarm settings and to turn the hourly time
signal on and off. Use the Snooze Alarm Mode to configure snooze alarm settings.
• You can input up to eight characters for the reminder text.
3. After you select an alarm, hold down A until the hour
setting of the alarm time starts to flash, which indicates
the setting screen.
• This operation automatically turns on the alarm.
To set a one-time alarm time
1. Enter the Alarm Mode.
• There are four alarm screens numbered
1
through
4
for the one-time alarm. The Hourly Time Signal screen
is indicated by
:00
.
2. Use D to scroll through the alarm screens until the one
whose time you want to set is displayed.
x1
:00
x2 x3
x4
Alarm time
(Hour : Minutes)
Alarm number
Timekeeping
Mode time
4. Press C to move the flashing in the sequence shown below to select other settings.
• Selecting the text causes the text input cursor (
) to appear. There are eight
spaces in the text, so you have to press C eight times to move to the Hour
setting.
5. When the setting you want to change is selected, press D to change it.
• While the hour or minute setting is flashing, press D (+) to change it.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (A indicator) or p.m. (P indicator).
• When inputting text, press D to cycle through characters at the current cursor
location, and C to move the cursor to the right. See “Inputting Text” for more
information.
• Pressing B and D at the same time while any setting is flashing automatically
sets the time to AM12:00. It also clears any text that is input for the alarm.
6. Press A to exit the setting screen.
Hour Minutes Text
• The text you input appears at the top of the display screen. If the reminder text is
more than five characters, it will scroll from right to left. Scrolling pauses for about
one second when the end of the text is reached.
To set the snooze alarm time
1. Enter the Snooze Alarm Mode.
2. Hold down A until the hour setting of the snooze alarm
time starts to flash, which indicates the setting screen.
• This operation automatically turns on the alarm.
3. Perform the steps from step 4 under “To set a one-time
alarm time” to finish setting the snooze alarm time.
Alarm time
(Hour : Minutes)
Timekeeping
Mode time
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, or until you turn the alarm off.
• To stop the alarm tone after it starts to sound, press any button.
• If you input reminder text for an alarm, the text appears for one minute on the
Timekeeping Mode screen when the alarm time is reached. You can clear the
reminder text display by exiting the Timekeeping Mode.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the
SNZ setting screen
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
To turn a one-time alarm on and off
1. In the Alarm Mode, use D to select an alarm.
2. Press A to toggle it on (ALM displayed) and off (ALM
not displayed).
• Turning on a one-time alarm (
1 through 4) displays the
alarm on indicator (ALM) on its Alarm Mode screen.
• In all modes (except the Recall Mode), the alarm on
indicator is shown for any alarm that is currently turned
on.
• The alarm on indicator flashes while the alarm is
sounding.
Alarm on indicator
To turn the snooze alarm on and off
In the Snooze Alarm Mode, press A to toggle it on (ALM
SNZ displayed) and off (ALM SNZ not displayed).
• The alarm on indicator (ALM) flashes while the alarm is
sounding.
• The alarm on indicator (ALM) and the snooze alarm
indicator (SNZ) both remain on the display in all modes
(except the Recall Mode) while the snooze alarm is
turned on.
• The snooze alarm indicator flashes during the 5-minute
intervals between alarms.
Snooze alarm
indicator
Alarm on
indicator
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select the Hourly Time
Signal (
:00).
2. Press A to toggle it on (SIG displayed) and off (SIG
not displayed).
• The Hourly Time Signal on indicator (SIG) is shown on
the display in all modes (except the Recall Mode) while
the Hourly Time Signal is turned on.
Hourly time signal
on indicator
Stopwatch
The stopwatch lets you measure elapsed time.
• The display range of the stopwatch is 23 hours, 59
minutes, 59 seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• All of the operations in this section are performed in the
Stopwatch Mode, which you can enter from the Mode
Menu screen.
1/100 second
Seconds
Minutes
To measure elapsed time
1. Press D to start the stopwatch.
2. Press D to stop the stopwatch.
• You can resume the measurement operation by
pressing D again.
• For the first 60 minutes, the screen shows minutes,
seconds, and 1/100 second. After 60 minutes, the
screen format changes to show hours, minutes, and
seconds.
3. Press B to clear the stopwatch to all zeros.
Seconds
Minutes
Hours
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Auto Display
Auto Display continually changes the contents of the
digital display.
To turn off Auto Display
Press any button to turn off Auto Display.
To turn on Auto Display
While the Mode Menu screen is on the display, press A
and C at the same time.