User manual

Module No. 2365/2366
2365/2366-1
GENERAL GUIDE
• Press
AA
AA
A to change from mode to mode.
Timekeeping Mode Stopwatch ModeDual Time ModeAlarm ModeCalendar Mode
ABOUT THE BACKLIGHT
• Press
LL
LL
L to illuminate the display for about 2 seconds.
• The backlight of this watch employs an electro-luminescent (EL) light, which loses
its illuminating power after very long term use.
• Frequent use of the backlight shortens the battery life.
• The watch emits an audible sound whenever the display is illuminated. This does
not indicate malfunction of the watch.
• The illumination provided by the backlight may be hard to see when viewed under
direct sunlight.
• The backlight automatically turns off whenever an alarm sounds.
• When the backlight is turned on, it blinks whenever the minute hand moves. This is
normal, and does not indicate malfunction of the watch.
• The backlight of Module 2366 illuminates both the digital display and analog face.
The backlight of Module 2365 illuminates the digital display only.
TIMEKEEPING MODE
• Use this mode to set the current time. An incorrect digital time setting will result in
incorrect operation of the calendar.
To set the time and date
1. Hold down
CC
CC
C until the seconds digits start to flash.
2. Press
AA
AA
A to reset the seconds to 00. If you press
AA
AA
A while the seconds count is in
the range of 30 to 59, the seconds are reset to 00 and 1 is added to the minutes. If
the seconds count is in the range of 00 to 29, the minutes count is unchanged.
3. Press
CC
CC
C to move the selection to the hour digits.
4. Press
AA
AA
A to increase the hour digits. Holding down
AA
AA
A changes the hour digits at
high speed.
5. Press
CC
CC
C to move the selection to the minutes digits.
6. Press
AA
AA
A to increase the minutes digits. Holding down
AA
AA
A changes the minutes
digits at high speed.
7. Press
CC
CC
C to move the selection to 12/24.
8. Press
AA
AA
A to toggle the timekeeping format between 12-hour and 24-hour.
• When 12-hour format is selected, the indicator P appears on the display to indicate
“p.m.” times. There is no indicator for “a.m.” times.
9. Press
CC
CC
C to complete the procedure.
• If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Timekeeping Mode automatically.
To set the hands
When in any Mode, press
BB
BB
B with a thin object to advance the analog time setting.
Each press of
BB
BB
B advances the time by 20 seconds. Three presses advance by one
minute.
Holding down
BB
BB
B advances the analog setting at high speed. You can only advance
the setting and cannot reverse it.
CALENDAR MODE
To set the date
1. Hold down
CC
CC
C until the month digits start to flash.
2. Press
AA
AA
A to increase the month digits. Holding down
AA
AA
A changes the digits at high
speed.
3. Press
CC
CC
C to move the selection to day digits.
4. Press
AA
AA
A to increase the day digits. Holding down
AA
AA
A changes the digits at high
speed.
5. Press
CC
CC
C to move the selection to the day of the week indication.
6. Press
AA
AA
A to advance to the next day. Holding down
AA
AA
A changes the indication at
high speed.
7. Press
CC
CC
C to complete the procedure.
• If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Calendar Mode automatically.
ALARM MODE
When the Daily Alarm is turned on, an alarm sounds for 20 seconds at the preset
time each day. When the Hourly Time Signal is switched on, the watch beeps every
hour on the hour.
To set the alarm time and to turn the Daily Alarm and Hourly Time Signal
on and off
Month Day of weekDay
Month Day
Day of week
Hold down
CC
CC
C.
Press
CC
CC
C.
Press
CC
CC
C. Press
CC
CC
C.
1. Hold down
CC
CC
C until the hour digits start to flash.
2. Press
AA
AA
A to increase the hour digits. Holding down
AA
AA
A changes the digits at high
speed.
• The format (12-hour and 24-hour) of the alarm time matches the format you select
for normal timekeeping.
3. Press
CC
CC
C to move the selection to the left minutes digit.
4. Press
AA
AA
A to increase the left minutes digit. Holding down
AA
AA
A changes the digit at
high speed.
5. Press
CC
CC
C to move the selection to the right minutes digit.
6. Press
AA
AA
A to increase the right minutes digit. Holding down
AA
AA
A changes the digit at
high speed.
7. Press
CC
CC
C to move Daily Alarm and Hourly Time Signal on and off setting.
8. Press
AA
AA
A to change the status of the Daily Alarm and Hourly Time Signal in the
following sequence.
• At this time Daily Alarm and Hourly Time Signal automatically turn on.
Hour
Alarm/Hourly Time Signal setting
Right
minutes
digit
Left
minutes
digit
Hour
Minutes
Mode indicator
Alarm on indicator
Hold down
CC
CC
C.
Press
CC
CC
C.
Press
CC
CC
C.
Press
CC
CC
C.
Press
CC
CC
C.
Hourly Time Signal on indicator
9. Press
CC
CC
C to complete the procedure.
• If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Alarm Mode automatically.
To stop the alarm
• Press any button to stop the alarm after it starts to sound.
To test the alarm and select an alarm tone
Hold down
AA
AA
A in any mode (except when making any settings) to sound the alarm.
Each time you test the alarm, a four different alarm tones. The alarm tone you select
is used for the Daily Alarm and Hourly Time Signal.
• Note that holding down
AA
AA
A also changes the mode.
Both ON Both OFF Daily Alarm
only
Hourly Time
Signal only
Seconds
12/24
Hour
Minutes
Hour Minutes
Seconds
PM indicator
Minute handHour hand
Hold down
CC
CC
C.
Press
CC
CC
C.
Press
CC
CC
C.
Press
CC
CC
C.
Press
CC
CC
C.