User manual

ManualsBrandsCasio ManualsWatch2349

2349-2

TELEMEMO MODE

The Telememo Mode lets you store up to 30 records, each

with a name (up to eight characters) and a phone number

(up to 14 digits). Records are automatically sorted based

on the names. You can recall records by scrolling through

them on the display.

• See the “CHARACTER LIST” for details on how the watch

sorts records.

• The blank screen appears when there are no records

stored in memory, or when you scroll to the location

between the last and the first records stored in memory.

• The record on the display when you exit the Telememo Mode appears first the next

time you enter the Telememo Mode.

To input a new Telememo record

1. In the Telememo Mode, press D and B at the same time. This causes the blank

screen to appear.

• If the blank screen does not appear when you press D and B, it means that memory

is full. To store another record, you will first have to delete a record stored in memory.

2. Hold down A and a cursor appears on the display.

3. Use D (+) and B (–) to scroll through characters at the current cursor position.

Characters scroll in the sequence shown below.

A ~ Z

0 ~ 9

(

(Space)

Press .

• Holding down D or B scrolls at high speed.

4. When the character you want is at the current cursor position, press C to move the

cursor to the right.

5. Repeat the steps 3 and 4 to input the rest of the characters.

6. After you input the name, use C to move the cursor to the right until the number input

screen “-----” appears.

• You can input up to eight characters for the name, though only six characters are

visible at a time. If the name you input has fewer than eight characters, use C to move

the cursor to the eighth space (which means you would press C three times after

inputting a five-character name).

• Pressing C again while the cursor is at the eighth space changes to the number input

screen. When the cursor is at the 14th digit of the number input screen, pressing C

causes the name input screen to appear again.

7. Use D (+) and B (–) to scroll through characters (hyphen, numbers, space) at the

current cursor position on the number screen. Characters scroll in the sequence shown

below.

0 ~ 9

(Space)

Press .

• Holding down D or B scrolls characters at high speed.

8. When the character you want is at the cursor position, press C to move the cursor to

the right.

9. Repeat steps 7 and 8 to input the rest of the numbers you want.

• You can input up to 14 digits for the number.

10.After inputting the name and number of the record, press A to store it.

• The message “SORT” appears on the display for a few moments after you press A to

indicate that the watch is sorting records.

• After the record is sorted, the cursor appears in the display, ready for input.

11.Input the next record or press A to exit the setting screen.

• The display can show only six name characters or nine number digits at a time. Longer

names and numbers scroll continuously from right to left. The symbol “

” indicates

that the character or digit to the left is the last, and the character or digit to the right is

the first.

• Pressing D while a name is scrolling on the display jumps to the first character of the

name. Scrolling resumes from there.

• Pressing A while a number is scrolling on the display jumps to the first digit of the

number. Scrolling resumes from there.

To recall Telememo data

1. In the Telememo Mode, press D to scroll forward through the names of the stored

records.

• Holding down D scrolls through the names at high speed.

2. When the name for the record you want is on the display, press A to view its number.

• Pressing D while a number screen is on the display returns to the name screen.

• At this point you could press D again to scroll through names.

To edit Telememo data items

1. In the Telememo Mode, press D to scroll forward through the names of the stored

records.

• Holding down D scrolls through the names at high speed.

2. When the name for the record you want is on the display, hold down A until the cursor

appears in the display.

3. Use C to move the cursor to the character you want to change.

4. Use D (+) and B (–) to change the character.

• See step 3 of “To input a new Telememo record” for information on inputting name

characters, and step 7 for inputting number characters.

5. After making the changes that you want, press A to store them and exit the setting

screen.

• The message “SORT” appears on the display for a few moments after you press A to

indicate that the watch is sorting records.

To delete Telememo data

1. In the Telememo Mode, press D to scroll forward through the names of the stored

records.

• Holding down D scrolls through the names at high speed.

2. When the name for the record you want is on the display, hold down A until the cursor

appears in the display.

3. Press D and B at the same time. The message “CLEAR” appears in the display,

indicating that the record was deleted.

• After the record is deleted, the cursor appears in the display, ready for input.

4. Input a record or press A to exit the setting screen.

ALARM MODE

You can set up to five daily alarms. When the Daily Alarm is

turned on, the alarm sounds for 20 seconds at the preset

time each day. Press any button to stop the alarm after it

starts to sound. When the Hourly Time Signal is turned on,

the watch beeps every hour on the hour.

To set the alarm time

1. While in the Alarm Mode, press D to display the number of the alarm you want to set.

Alarm 1 Alarm 5Alarm 2 Alarm 3 Alarm 4

Hourly Time Signal

2. Hold down A until the hour digits flash on the display, indicating the setting screen.

• At this time, the alarm is turned on automatically.

3. Press C to move the flashing in the sequence shown below.

Hour Minutes

4. Use D (+) and B (–) to change the setting. Holding down either button changes the

setting at high speed.

5. After you set the alarm time, press A to exit the setting screen.

• The format (12-hour and 24-hour) of the alarm time matches the format you select in

the Timekeeping Mode.

• When setting the alarm time using the 12-hour format, take care to set the time

correctly as morning or afternoon.

To stop the alarm

• Press any button to stop the alarm after it starts to sound.

To turn a daily Alarm or the Hourly Time Signal on and off

1. Use D to display the alarm you want to turn on or off, or the screen for turning the

Hourly Time Signal on or off.

2. Press A to toggle the displayed alarm or Hourly Time Signal on and off.

• In the Alarm Mode, the alarm on indicator appears to indicate the on/off status of the

currently displayed alarm. In all other modes, the alarm on indicator appears when any

one of the five alarms is turned on. The alarm on indicator is not displayed in other

modes when all alarms are turned off.

• The Hourly Time Signal indicator is displayed in all modes when the Hourly Time

Signal is turned on.

To test the alarm

In the Alarm Mode, hold down D to sound the alarm.

• The alarm test does not work while the Alarm Mode setting screen is on the display.

• Holding down D to test the alarm also advances to the next alarm number.

STOPWATCH MODE

The Stopwatch Mode lets you measure elapsed time, split

times, and two finishes. The range of the stopwatch is 59

minutes, 59.99 seconds. You can use the EL backlight by

pressing B at any time while the stopwatch is operating.

Elapsed time measurement

Start

Stop Re-start Stop Clear

Start

Split Split release Stop Clear

Start

Split Stop Split release Clear

Split time measurement

Split time and 1st-2nd place times

First runner

finishes.

Second runner

finishes.

Record time of

first runner.

Record time of

second runner.

Daily Alarm indicator

Hourly Time

Signal indicator

Mode indicator

1/100 second

Minutes

Seconds

Press D.

Press A.

Mode indicator

Name

Remaining memory

Telephone number

Mode indicator

Alarm number

Hour Minutes

Alarm on indicator