User manual

Module No. 2174/2292
2174/2292-1
GENERAL GUIDE
• The operational procedures for Modules 2174 and 2292 are identical. All of the illustrations in this manual show Module 2174.
• Press B to change from mode to mode.
• Pressing L in any mode illuminates the display for about 3 seconds.
• If you do not perform any operation for a few minutes while a setting screen (with flashing digits) is on the display, the watch automatically exits the setting screen.
• If you do not perform any operation for a few minutes in the Day Counter Mode or Telememo Mode, the watch automatically reverts to the normal timekeeping screen.
Day Counter Mode Telememo Mode Stopwatch Mode Alarm ModeTimekeeping Mode World Time Mode
Press B.
[Module 2292] [Module 2174]
TIMEKEEPING MODE
• Press C to toggle the display between the day of the week and month, as shown
below.
Press C.
Hour
Minutes
City code
Seconds
DST on
indicato
r
Day
Month
Day of week
• Hold down C to toggle between 12-hour and 24-hour timekeeping. Note that
pressing C also switches the display between the day of the week and month
screens as described above.
• With 12-hour timekeeping, times between midnight and noon are indicated by A
(am), while times between noon and midnight are indicated by P (pm).
• The A and P indicators do not appear when you are using 24-hour timekeeping.
To set the time and date
1. While in the Timekeeping Mode, hold down A until the second’s digits flash on the
display, indicating the setting screen.
2. Press B to move the flashing in the sequence shown below.
DST
Seconds
Month
Day
City code
Minutes
Ye a r
Hour
3. While the second’s setting is selected (flashing), press C to reset it to 00. If you
press C while the second’s setting is in the range of 30 to 59, the seconds are
reset to 00 and 1 is added to the minutes. If the second’s setting is in the range of
00 to 29, the minute’s count is unchanged.
• While the DST
∗
setting is selected (DST on indicator is flashing), press C to toggle
it on (ON) and off (OF).
• The DST on/off setting you make for the Timekeeping Mode does not affect the
World Time Mode.
• While the city codes setting is selected, use C to scroll through the available codes
until the one you want to use as your home time city is displayed.
• For full information on city codes, see the “CITY CODE TABLE”.
4. While any other setting is selected (flashing), press C to increase it. Holding down
C changes the setting at high speed.
5. After you make the settings you want, press A to exit the setting screen.
• The day of the week is automatically set in accordance with the date.
• The date can be set within the range of January 1, 2000 to December 31, 2039.
• The watch’s built-in full automatic calendar automatically makes allowances for
different month lengths and leap years. Once you set the date, there should be no
reason to change it except after the replacement of the watch’s battery.
∗
Daylight Saving Time (DST), which is also sometimes called “summer time”
advances the time for one hour, as is the custom in some areas during the summer.
Remember that not all countries or even local areas use Daylight Saving Time.
ABOUT THE BACKLIGHT
• Press L to illuminate the display for about three seconds.
• The backlight of this watch employs an electro-luminescent (EL) light, which loses
its illuminating power after very long term use.
• Frequent use of the backlight shortens the battery life.
• The watch emits an audible sound whenever the display is illuminated. This does
not indicate malfunction of the watch.
• The illumination provided by the backlight may be hard to see when viewed under
direct sunlight.
• The backlight automatically turns off whenever an alarm sounds.
WORLD TIME MODE
Hour : Minutes
Seconds
DST on indicator
Day
Day of week
Mode indicator
City code
Month
[Month-day display]
The World Time Mode shows the current time in 40 cities (27 time zones) around the
world. The lower part of the display shows either the day of the week and day, or the
month and day. The format used is the one you select in the Timekeeping Mode
before entering the World Time Mode.
• For full information on city codes, see the “CITY CODE TABLE”.
• The time setting of the Timekeeping Mode and the World Time Mode are
synchronized, except for the daylight saving time (summer time) setting. Whenever
you change the time setting for any city in the Timekeeping Mode, the settings of all
World Time cities are changed accordingly.
• The World Time Mode has its own daylight saving time (summer time) setting.
To select a World Time City and view its time
In the World Time Mode, press C to scroll forward through the city codes (time
zones). Holding down C scrolls at high speed.
• You can set up an alarm in the Alarm Mode so it operates based on the current time
in a city you specify in the World Time Mode.
Daylight Saving Time (DST)
Daylight Saving Time automatically advances the time setting by one hour from
Standard Time. You cannot make individual Daylight Saving Time settings for each
city code (time zone). Turning on Daylight Saving Time affects all World Time time
zones. Remember that not all countries or even local areas use Daylight Saving Time.
To switch between Standard Time and Daylight Saving Time
In the World Time Mode, hold down A toggle between Daylight Saving Time and
Standard Time.
DST on indicator
DST OFF DST ON
[Module 2174] [Module 2292]
DAY COUNTER MODE
The Day Counter Mode lets you count the number of days from the Timekeeping
Mode’s current date to a specific target date.
This watch has five day counters. You can assign text titles up to eight characters long
to each of the five Day Counters. Whenever the date specified by any one of the day
counters matches the date of the Timekeeping Mode (regardless of the day counter’s
year setting), the DAYS indicator flashes on the Timekeeping Mode. In the
Day Counter Mode, the DAYS indicator flashes on the screen of the particular day
counter whose date matches the date of the Timekeeping Mode.
The initial default date for all Day Counters is January 1, 2001.
[Module 2174] [Module 2292]
Year
Month - Day
Target date
Numbers of days
Tex t
DAYS indicator
Mode indicator
Alternate at the
1-second interval.
• The day counter on the display when you exit the Day Counter Mode appears first
the next time you enter the Day Counter Mode.
Hold
down A.