User manual

ManualsBrandsCasio ManualsWatch2217

Module No. 2217

2217-1

GENERAL GUIDE

• If the display of your watch is continually changing, see “Auto Display Function” for information on how to stop it.

• Press

D to change from mode to mode.

• When you return to the Timekeeping Mode from another mode, the Home City code appears first, followed after a few seconds by the current time. See “TIMEKEEPING MODE” for details.

• In any mode (except for the Memo Mode or when making any settings) press

A to illuminate the display for about 1.5 seconds.

Alarm 2 Mode Memo ModeStopwatch ModeTimekeeping Mode Day Counter Mode Alarm 1 ModeWorld Time Mode

Press

TIMEKEEPING MODE

In addition to normal timekeeping, use the Timekeeping

Mode to set the current time and date.

Setting the Current Time

Use the following procedure to select a city (city code) as

your Home City, and then set its time and date. You can

also specify whether you prefer to use 12-hour or 24-hour

timekeeping for all screens that show times.

• Changing the city code setting usually changes the time

setting and sometimes changes the date setting. Because

of this, you should select your Home City before setting

time and date.

• Once you select a Home City and set its time, you can

view the current time in other cities by simply changing

the city code setting.

To set the current time

1. In the Timekeeping Mode, hold down

C until the city code

starts to flash on the display. The city code flashes

because it is

selected

2. Use

A and

B to scroll through the city codes until the

one you want to set as your Home City is displayed.

•

B scrolls forward, while

A scrolls back through city codes.

• See the “CITY CODE TABLE” for a complete list of avail-

able codes.

3. Press

D to move the flashing in the sequence shown

below to select other settings.

Seconds

PM indicator

Hour Minutes

City code

City Code Seconds Hour Minutes

Day Month Year

12/24-Hour

format

4. Press

D until the seconds digits are flashing on the display.

5. While the seconds digits are selected (flashing), press

B to reset the seconds to

• Pressing

B while the seconds count is in the range of 30 to 59 resets the seconds to

and adds 1 to the minutes. If the seconds count is in the range of 00 to 29, the

minutes count is unchanged.

6. Press

D until the hour digits are flashing on the display.

7. Press

B increase the setting or

A to decrease it.

8. Repeat steps 6 and 7 to set the minutes, year, month, and day.

• When the 12/24-hour setting is selected, press

B to toggle between 12-hour (

12H)

and 24-hour (

24H) timekeeping.

9. After you make the settings you want, press

C to return to the current time screen.

Viewing the Current Date and World Time Mode Screens

In the Timekeeping Mode, press

C to display the current date screen, and

B to display

the World Time Mode screen. The screen you select remains on the display for a few

seconds, and then the watch returns to the current time.

ABOUT THE BACKLIGHT

About the Auto Light Switch Function

When the auto light switch function is turned on, the backlight automatically turns on for

1.5 seconds under the conditions described below. Avoid wearing the watch on the

inside of your wrist. Doing so causes the auto light switch to operate when not needed,

which shortens battery life.

Moving the watch to a position that is parallel to the ground and then tilting it

towards you approximately 40 degrees causes the backlight to illuminate.

• The backlight may not illuminate if the face of the watch is more than 15 degrees off

parallel to the left or right. Make sure that the back of your hand is parallel to the

ground.

Parallel to ground More than 15 degrees More than 15 degrees

too high too low

• Static electricity or magnetic force can interfere with proper operation of the auto light

switch function. If the backlight does not illuminate, try moving the watch back to the

starting position (parallel with the ground) and then tilt it back toward you again. If this

does not work, drop your arm all the way down so it hangs at your side, and then bring

it back up again.

• Under certain conditions the backlight may not light until about one second or less

after turning the face of the watch towards you. This does not necessarily indicate

malfunction of the backlight.

To switch the auto light switch function on and off

In any mode (except for the Memo Mode or when making any settings), hold down

A for

two seconds to turn the auto light switch function on and off.

• The auto light switch indicator is shown on the display in all modes while the auto light

switch function is on.

• In order to protect against running down the battery, the auto light switch function is

automatically turned off approximately five hours after you turn it on. Repeat the above

procedure to turn the auto light switch function back on if you want.

• In any mode (except for the Memo Mode or when making any settings) press

A to

illuminate the display for about 1.5 seconds, regardless of the auto light switch's on/off

setting.

Caution

• The backlight of this watch employs an electro-luminescent (EL) light, which loses its

illuminating power after very long term use.

• Frequent use of the backligfht shortens the battery life.

• The watch emits an audible sound whenever the display is illuminated. This is be-

cause the EL light vibrates slightly when lit. It does not indicate malfunction of the

watch.

Warning!

• Never try to read your watch when mountain climbing or hiking in areas that are

dark or in areas with poor footing. Doing so is dangerous and can result in

serious personal injury.

• Never try to read your watch when running where there is the danger of acci-

dents, especially in locations where there might be vehicular or pedestrian traf-

fic. Doing so is dangerous and can result in serious personal injury.

• Never try to read your watch when riding on a bicycle or when operating a mo-

torcycle or any other motor vehicle. Doing so is dangerous and can result in a

traffic accident and serious personal injury.

• When you are wearing the watch, make sure that its auto light switch function is

turned off before riding on a bicycle or operating a motorcycle or any other

motor vehicle. Sudden and unintended operation of the auto light switch can

create a distraction, which can result in a traffic accident and serious personal

injury.

Parallel to ground

Hold down

Off

Auto light switch

indicator

[Date] [World Time Mode]

Month Day of week Current time in the selected city

City code

Day

Summary of content (3 pages)

PAGE 1
Module No. 2217 2217-1 GENERAL GUIDE • • • • If the display of your watch is continually changing, see “Auto Display Function” for information on how to stop it. Press D to change from mode to mode. When you return to the Timekeeping Mode from another mode, the Home City code appears first, followed after a few seconds by the current time. See “TIMEKEEPING MODE” for details. In any mode (except for the Memo Mode or when making any settings) press A to illuminate the display for about 1.5 seconds.
PAGE 2
217-2 DAY COUNTER MODE ALARM MODES You can set up to two daily alarms named Alarm 1 and Alarm 2, and even specify a city code for the alarm. Home time • When you enter the Alarm 1 or Alarm 2 Mode, the alarm time setting and the city code currently assigned to indicator that alarm appear on the display. • The home time indicator ( ) appears when HOME is selected as the city code assigned to the alarm.
PAGE 3
2217-3 Auto Display Function MEMO MODE Memo text Memo number The Auto Display function of this watch continually changes the contents of the digital display. Note that you cannot use any of the watch’s other functions (except for backlight) while the Auto Display function is operating. The Memo Mode lets you input up to 30 memos for instant recall when you need them. • Memos are numbered from 1 to 30, and are stored in sequential order starting from 1.