User manual

ManualsBrandsCasio ManualsWatch2203

2203/2204/2205-2

ALARM MODE

Mode indicator

Alarm number

Melody name

Hour

Minutes

Current time

You can set up to five melody alarms. When a Daily Alarm is turned on, its melody

alarm sounds for about 20 seconds at the preset time each day. Press any button

(except

E) to stop the melody alarm after it starts to sound. Pressing

E while a

melody is playing toggles the display between an animated character and the name

of the melody that is playing. When the Hourly Time Signal is turned on, the watch

beeps every hour on the hour.

To set the alarm time

1. While in the alarm Mode, press

D to display the alarm number you want to set.

Alarm 1 Alarm 5Alarm 2 Alarm 3 Alarm 4

SIG: 00 (Hourly Time Signal)

2. Hold down

A until the melody name starts to flash on the display, indicating the

setting screen. The alarm is automatically turned on at this time.

3. Press

C to change the selection in the sequence shown below.

Melody Name Hour Minutes

4. While melody setting is selected, use

D or

B to scroll through melody names.

Setting Alarm Sound

– 0

– 1

– 2

– 3

– 4

– 5

–

Random play of melodies 1, 2, 3, 4 and 5

Melody 1

Melody 2

Melody 3

Melody 4

Melody 5

Beeper

Press .

∗

See the “MELODY LIST” for the names of melodies.

∗

Some melody alarms tune names may be displayed in abbreviated format.

• While any other setting is selected, press

D to increase it or

B to decrease it.

Holding down either button changes the setting at high speed.

5. After you make the settings you want, press

to exit the setting screen.

• The format (12-hour and 24-hour) of the alarm time matches the format you select

for normal timekeeping.

• When setting the alarm time using the 12-hour format, take care to set the time

correctly as morning or afternoon.

To stop a melody alarm

• Press any button (except

E) to stop a melody alarm after it starts to sound.

To turn a daily Alarm or the Hourly Time Signal on and off

1. Use

D to display the alarm you want to turn on or off, or the screen for turning the

Hourly Time Signal on or off.

2. Press

B to toggle the displayed alarm or Hourly Time Signal on and off.

• Alarm indicator 1 is displayed in the alarm mode only. It

indicates the on/off status of the currently displayed

alarm only. Note that this indicator is used for different

purposes in other modes.

• Alarm indicator 2 is displayed in all modes when any of

the five alarms is turned on.

• Alarm indicator 3 is displayed in the Alarm Mode only.

It shows ON when the currently displayed alarm is on,

and OF when the currently displayed alarm is off.

• Hourly Time Signal indicator 1 is displayed in the Alarm

Mode only when the Hourly Time Signal is turned on.

Note that this indicator is used for different purposes in

other modes.

• Hourly Time Signal indicator 2 is displayed in all modes

when the Hourly Time Signal is turned on.

• Hourly Time Signal indicator 3 is displayed in the Alarm

Mode only. It shows ON when the Hourly Time Signal

is on, and OF when the Hourly Time Signal is off.

To test the alarm

In the Alarm Mode, display the alarm you want to sound,

and then press

E to play its melody or beep. You can

also press

E to play an alarm’s melody while setting the

alarm time.

• To stop a playing melody or beep, press any button.

Alarm indicator 1

Alarm indicator 2

Alarm indicator 3

Hourly Time Signal

indicator 1

Hourly Time Signal

indicator 2

Hourly Time Signal

indicator 3

STOPWATCH MODE

The stopwatch Mode lets you measure elapsed time, split

times, and two finishes. The range of the stopwatch is 23

hours, 59 minutes, 59.99 seconds. You can use the EL

backlight by pressing

E at any time while the stopwatch

is operating.

Elapsed time measurement

Start

Stop Re-start Stop Clear

Start

Split Split release Stop Clear

Start

Split Stop Split release Clear

Split time measurement

Split time and 1st-2nd place times

First runner

finishes.

Second runner

finishes.

Record time of

first runner.

Record time of

second runner.

MEMO MODE

The Memo Mode lets you store up to five memos, each

with an eight-character title and 16 characters of data.

Recalling a Memo

In the Memo Mode, press

D to scroll through the Memo

titles. When you find the title you want, press

B, and the

screen alternates between the title and data.

• The display can show only five characters at a time.

Longer text scrolls continuously from right to left. The

symbol “

” indicates that the character or digit to the

left is the last, and the character or digit to the right is

the first.

• A series of hyphens “ – – – – – ” is displayed for a memo

that does not contain any data.The display can show

only five characters at a time.

To input a memo

1. In the Memo Mode, press

D to display the memo number you want to set.

2. Hold down

A until the first (leftmost) character of the memo title starts to flash on

the display. This indicates the input screen.

3. Press

C to move the flashing in the sequence shown below. Press

E to move the

flashing in the opposite direction.

Press . Press .

Title Character 8

Data Character 1

Title Character 1

Data Character 16

4. Use

D or

B to scroll through characters at the current location of the flashing.

Holding down either button scrolls at high speed.

Press . Press .

Space A to Z

Punctuation

Japanese

characters

Hyphen SymbolsNumbers

∗

See the “CHARACTER LIST” at the back of this manual for details.

• Pressing

D and

B at the same time while inputting memo title or data clears all title

and data. At this time the message “CLEAR” appears on the display.

5. After you input the data you want, press

A to exit the input screen.

Mode indicator

Hours

Minutes

Seconds

1/100 second

Current tim

Mode indicator

Memo number

Title