User manual

2047-2
Elapsed time measurement
Start
Stop Re-start Stop Clear
Start
Split Split release Stop Clear
Start
Split Stop Split release Clear
Split time measurement
Split time and 1st-2nd place times
First runner
finishes.
Second runner
finishes.
Record time of
first runner.
Record time of
second runner.
STOPWATCH MODE
The stopwatch Mode lets you measure elapsed time, split
times, and two finishes. The range of the stopwatch is 23
hours, 59 minutes 59.99 seconds. You can use the EL
backlight at any time while the stopwatch is operating by
pressing
BB
BB
B.
TIDE MODE
The Tide Mode lets you view tide data for a specific date
and time at the point you want.
To specify the point, date, and time of the tide
1. Hold down
AA
AA
A until the point name and point number
start to flash.
is the time you set in Timekeeping
Mode.
2. Press
CC
CC
C to move the selection around the display in
the following sequence.
3. While any digits are selected (flashing), press
DD
DD
D to increase the number or
BB
BB
B to
decrease it. Holding down either button changes the current number at high speed.
4. After you are finished making the settings you want, press
AA
AA
A to return to the Tide
Mode.
• If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Tide Mode automatically.
5. Press
DD
DD
D to select the time whose tide you want to view. Each press of
DD
DD
D advances
the time. Holding down
DD
DD
D advances the time at high speed.
• Pressing
DD
DD
D while the tide for 11:00pm is displayed advances to midnight (00:00am),
but the date does not change. This means the tide data shown is for midnight
(00:00am) of the current date.
ALARM MODE
• You can set an alarm for a specific point. The alarm will
sound when the time in the point you select reaches the
alarm time.
• When the Hourly Time Signal is turned on, the watch
beeps every hour on the hour in the point you select.
To set the alarm time
1. Hold down
AA
AA
A until the point name and point number start to flash on the display.
2. Press
CC
CC
C to change the selection in the following sequence.
Hour Minutes
Point name
Point number
3. Press
DD
DD
D to increase the number or
BB
BB
B to decrease it. Holding down either button
changes the current number at high speed.
• The format (12-hour and 24-hour) of the alarm time matches the format you select
for normal timekeeping.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as morning or afternoon.
4. After you set the alarm time, press
AA
AA
A to return to the Alarm Mode. At this time the
Alarm is automatically switched on.
• If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Alarm Mode automatically.
To stop the alarm
• Press any button to stop the alarm after it starts to sound.
To turn the alarm and Hourly Time Signal on and off
Press
DD
DD
D while in the Alarm Mode to change the status of the alarm and Hourly Time
Signal in the following sequence.
Hourly Time
Signal Only
Alarm Only
Both OFFBoth ON
To test the alarm
Hold down
DD
DD
D while in the Alarm Mode to sound the alarm.
COUNTDOWN ALARM MODE
The countdown alarm can be set within a range of 1 minute
to 60 minutes. When the countdown reaches zero, an
alarm sounds for 10 seconds or until you press any but-
ton.
To set the countdown start time
1. Hold down
AA
AA
A while in the Countdown Alarm Mode. The minutes digits flash on the
display.
2. Press
DD
DD
D to increase the value or
BB
BB
B to decrease it. Holding down either button
changes the value at thigh speed.
3. After you set the countdown start time, press
AA
AA
A to return to the Countdown Alarm
Mode.
• If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Countdown Alarm Mode automati-
cally.
To use the countdown alarm
1. Press
DD
DD
D while in the Countdown Alarm Mode to start the countdown alarm.
2. Press
DD
DD
D again to stop the countdown alarm.
• You can resume countdown alarm operation by pressing
DD
DD
D.
3. Press
DD
DD
D to stop the countdown alarm, and then press
AA
AA
A to reset the countdown
time to its starting value.
• When the end of the countdown is reached, the alarm sounds for 10 seconds or
until you stop the alarm by pressing any button. Countdown timing stops and the
countdown time is automatically reset to its starting value after the alarm stops.
• The watch beeps as the countdown time passes the 5-minute mark.
Point name
Point number
Year DayMonth
Mode indicator
Mode indicator
Minutes
Seconds
1/100 Second
Hours
Mode indicator
Minutes
Seconds