User manual

1865-2
TELEMEMO MODE
The Telememo Mode lets you store up to 30
pairs of name and telephone number data.
Data is automatically sorted based on the
characters of the name. You can recall data by
scrolling through it on the display.
• See the “CHARACTER LIST” at the back of
this manual for details on how the watch sorts
data.
• The new data screen appears when there is
no data stored in memory, or when you scroll
to the location between the last and the first
data items stored in memory.
• The data item on the display when you exit
the Telememo Mode appears first the next
time you enter the Telememo Mode.
• If you do not operate any button for a few
minutes while in the Telememo Mode, the
watch automatically goes back to the
Timekeeping Mode.
To edit Telememo data items
1. In the Telememo Mode, scroll through the data items and display the one you want to
edit.
2. Press A and a cursor appears in the animation area.
3. Use M to move the cursor to the character you want to change.
4. Use B to change the character.
• For details on inputting characters, see “To input new Telememo data” (steps 3 for
name input and 7 for number).
5. After making the changes that you want, press A to store them and return to the
Telememo Mode data screen.
To delete Telememo data
1. In the Telememo Mode, scroll through the data items and display the one you want to
delete.
2. Press A and a cursor appears in the animation area.
3. Hold down B and M at the same time until the message
CLR (clear) appears in the
animation area.
• At this time the cursor appears in the animation area, ready for input.
4. Input data or press A to return to the Telememo Mode data screen.
STOPWATCH MODE
The Stopwatch Mode measures elapsed time and
cumulative elapsed time. The range of the stopwatch is 23
hours, 59 minutes, 59.99 seconds.
To measure elapsed time
1. Press B to start the stopwatch.
2. Press B to stop the stopwatch.
3. Press A to clear the stopwatch to all zeros.
• Instead of pressing A, you can also clear the stopwatch
by holding down B for a few seconds.
To measure cumulative elapsed time
1. Press B to start the stopwatch.
2. Press B to stop the stopwatch.
3. Press B again to resume timing from the time shown on the display.
• You can repeat steps 2 and 3 as many times as you like.
4. Press A to clear the stopwatch to all zeros.
• Instead of pressing A, you can also clear the stopwatch by holding down B for a few
seconds.
ALARM MODE
When the Daily Alarm is turned on, the alarm sounds
for 20 seconds at the preset time each day. Press
any button to stop the alarm after it starts to sound.
When the Hourly Time Signal is turned on, the watch
beeps every hour on the hour.
To set the alarm time
1. Press A while in the Alarm Mode. The hour digits
flash on the display because they are
selected .
• This operation automatically turns on the Daily
Alarm.
2. Press M to change the selection in the following
sequence.
3. Press B to increase the selected digits. Holding down B increases the selection at
high speed.
• The format (12-hour and 24-hour) of the alarm time matches the format you select for
normal timekeeping.
• When setting the alarm time using the 12-hour format, take care to set the time correctly
as a.m. (AM indicator) or p.m. (PM indicator).
4. After you set the alarm time, press A to return to the Alarm Mode.
• If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Alarm Mode automatically.
AM
PM
DST
SIG
ALM
A
M
B
AM
PM
DST
SIG
ALM
SIG
ALM
[New Data Screen]
Telephone
number
Remaining memory
Name
A
M
B
AM
PM
DST
SIG
ALM
SecondsHours
Minutes
1/100 second
Hourly time
signal on
indicator
A
M
B
AM
PM
DST
SIG
ALM
Hour : Minutes
Alarm on
indicator
AM indicator
Hour
Minutes
To turn the Daily Alarm and Hourly Time Signal on and off
Press B while in the Alarm Mode to change the status of the Daily Alarm and Hourly
Time Signal in the following sequence.
[Alarm On Indicator/Hourly Time Signal On Indicator]
To test the alarm
Hold down B while in the Alarm Mode to sound the alarm.
Hourly Time
Signal Only
Both ON Both OFF
Daily Alarm
Only
SIG
ALM
ALM
SIG
To input new Telememo data
1. In the Telememo Mode, press B until the new data screen
appears.
• In the Telememo Mode, the animation area of the display
is used for name input and display.
• If the message
FULL appears in the number area of the
display, it means that memory is full. To store more data,
you will first have to delete some of the data stored in
memory.
2. Press A and a cursor appears in the animation area.
3. Use B to change the character at the cursor position in
the animation area. The character changes in the following
sequence.
• Holding down B changes the character at high speed.
4. When the character you want is at the cursor position, press M to move the cursor to
the right.
5. Repeat the steps 3 and 4 until your text is complete.
• You can input up to eight characters for the name.
6. After you input a name, use M to move the cursor to the number area.
• There are eight spaces provided for input of characters of each name, though only
three characters are visible at a time in the animation area. If the name you input has
less than eight characters, use M to move the cursor to the eighth space (which
means you would press M three times after inputting a 5-character name, for example).
Pressing M again while the cursor is at the eighth space causes it to jump down to the
first digit in the number area. When the cursor is at the 12th digit of the number area,
pressing M causes it to jump back up to the first character of the name.
7. Use B to change the character (hyphen, number, or space) at the cursor position in
the number area. The character changes in the following sequence.
• Holding down B changes the character at high speed.
8. When the character you want is at the cursor position, press M to move the cursor to
the right.
9. Repeat steps 7 and 8 until you complete number input.
• You can input up to 12 digits for the number.
10. After inputting your data, press A to store it and return to the Telememo Mode data
screen (without the cursor).
• If you do not perform any button operation for few minutes while the cursor is on the
display, the watch automatically returns to the Telememo Mode data screen.
• The animation area of the display can show only three characters at a time, so longer
text scrolls continuously from right to left.
• The number area can show up to six digits at one time. If a number has more than six
digits, the display automatically switched between the first six digits (counting forward
from the first digit) and the last six digits (counting backward from the last digit) of the
number. This means that if a number is 12 digits long, the number area switches
between the first six digits and the last six digits. If a number is 9 digits long, the
number area switches between digits 1 through 6, and digits 4 through 9.
To recall Telememo data
In the Telememo Mode, press B to scroll forward through stored data items.
• Holding down B scrolls through the data at high speed.
A
M
B
AM
PM
DST
SIG
ALM
Cursor
Animation area
Number area
(space)
A to
Z to 9 . -
(space)
0 to 9
x
Animation Area Number Area
03-5334-4111
Last letter of text
Separator
(inserted automatically)
SIG
ALM
▲
03-123-45
SIG
ALM
SIG
ALM
▲
SIG
ALM
▲▲