User manual

ManualsBrandsCasio ManualsWatch1865

1865-1

GENERAL GUIDE

Module No. 1865

• If the digital display of your watch is continually changing, see “AUTO DISPLAY

FUNCTION” for information on how to stop it.

• Press M to change from mode to mode.

• The animation area shows different animated characters and graphics, depending on

the mode and the operation being performed.

TIMEKEEPING MODE

This section provides information on setting the time and

date.

• The animation area of the Timekeeping Mode normally

shows the day of the week.

(G-SHOCK) mark appears

at 00, 20, 40 second point of each minute.

To set the time and date

1. Press A while in the Timekeeping Mode. The seconds

digits flash on the display because they are

selected

2. Press M to change the selection in the following

sequence.

WORLD TIME MODE

The World Time Mode shows the current time in 29 time

zones (28 cities) around the world.

• The time settings of the Timekeeping Mode and the World

Time Mode are independent, so you must make separate

settings for each. Note, however, that the seconds counts

for both modes are synchronized with each other.

• Whenever you change the time setting for any city in the

World Time Mode, the settings of all other cities are

changed accordingly.

• The GMT differentials used by this watch are based on

Universal Time Coordinated (UTC) data.

• The time zone that is displayed when you leave the World

Time Mode will still be displayed when you enter the World

Time Mode again.

• A rotating globe is normally in the animation area of the display while in the World Time

Mode. The rotating globe is replaced by the city code for the currently displayed time

at the 00, 20, and 40 second point of each minute. The city code remains displayed for

about two seconds.

To view the time in another zone

1. While in the World Time Mode, press B to display the city code for the time currently

shown on the display.

• Pressing B also turns on the backlight for about two seconds.

2. Press B again to scroll forward through the city codes (time zones).

• Each press of B advances to the next sequential city code.

• Holding down B scrolls at high speed.

• If you want to press B more than once to scroll through city codes, note that you

should not let more than about three seconds pass between B button operations.

Otherwise, the scrolling operation will be cancelled, and the next press of B will simply

display the current city code and turn on the backlight, as in step 1 of the above

procedure.

• For full information on city codes, see the “CITY CODE TABLE” at the back of this

manual.

Telememo Mode

Press M

▲

DAY

DST

SIG

ALM

Timekeeping Mode

DST

SIG

ALM

Alarm Mode

DST

SIG

ALM

World Time Mode

▲

DST

SIG

ALM

DST

SIG

ALM

Stopwatch Mode

▲

Animation area

DAY

DST

SIG

ALM

Hour : Minutes

Seconds

Day

Animation area

Day of week

PM indicator

DST

SIG

ALM

Animation area

GMT differential

Current time in

the selected city

City code

To set the World Time

1. In the World Time Mode, use B to scroll through the

time zones and find the one you want.

2. Press A. The DST On/Off setting flashes on the display

because it is

selected

• The DST indicator flashes along with the current on/off

setting.

3. Press M to change the selection in the following

sequence.

4. While DST On/Off setting is selected (flashing), press B toggle Daylight Saving Time

on (

ON) and off (OF). While the hour or minutes digits are selected, press B to

increase the setting.

• Holding down B while the hour or minutes digits are selected changes the setting at

high speed.

• The 12-hour/24-hour format of the World Time matches the format you select in the

Timekeeping Mode.

5. After you set the time, press A to return to the World Time Mode.

• If you do not operate any button for a few minutes while a selection is flashing, the

flashing stops and the watch goes back to the World Time Mode automatically.

To switch between standard time and daylight saving time

Daylight saving time (DST), which is also sometimes called “summer time,” advances

the time for one hour, as is the custom in some areas during the summer. Remember

that not all countries or even local areas use Daylight Saving Time.

1. In the World Time Mode, display the time zone whose standard/daylight saving time

setting you want to change.

• You can make separate daylight saving time settings for each individual city.

2. Press A. The DST On/Off setting flashes on the display because it is

selected

• The DST indicator flashes along with the current on/ off setting.

3. Press B to toggle Daylight Saving Time on (

ON) and off (OF).

4. After you are finished making the setting you want, press A to return to the World

Time Mode.

• The DST indicator is on the display whenever you display a city for which daylight

saving time is turned on.

DST

SIG

ALM

DST indicator

DST On/Off

Hour

Minutes

3. While the seconds digits are selected (flashing), press B to reset the seconds to 00.

• If you press B while the seconds count is in the range of 30 to 59, the seconds are

reset to

00 and 1 is added to the minutes. If the seconds count is in the range of 00 to

29, the minutes count is unchanged.

4. While hour, minutes, year, month, or day is selected (flashing), press B to increase

the number. The 12/24-hour setting is selected (flashing), press B to switch between

the 12-hour (

12H) and 24-hour ( ) formats.

• Holding down B changes the current selection at high speed.

• With the 12-hour format, the PM indicator appears for times in the range of noon to

11:59 pm and the AM indicator appears for times in the range of midnight to 11:59 am.

• With the 24-hour format, times are indicated in the range of 00:00 to 23:59, without any

indicator.

5. After you set the time and date, press A to return to the Timekeeping Mode.

• The day of the week is automatically set in accordance with the date.

• The date can be set within the range of January 1, 1995 to December 31, 2039.

• If you do not operate any button for a few minutes while a selection is flashing, the

flashing stops and the watch goes back to the Timekeeping Mode automatically.

BACKLIGHT

In the Timekeeping Mode and World Time Mode, press B to illuminate the display for

about two seconds.

• The backlight may not turn on when you press B under certain conditions in the

World Time Mode. See “To view the time in another zone” for details.

• The backlight of the watch employs an electro-luminescent (EL) light, which loses

illuminating power after very long use.

• The illumination provided by the backlight may be hard to see when viewed under

direct sunlight.

• The watch will emit an audible sound whenever the display is illuminated. This is caused

by a transformer that vibrates when the EL panel lights up. It does not indicate

malfunction of the watch.

• The backlight automatically turns off whenever an alarm sounds.

Seconds

Hour

Minutes

Day

Month Year

12/24-Hour

Format

Summary of content (3 pages)

PAGE 1
Module No. 1865 1865-1 GENERAL GUIDE • If the digital display of your watch is continually changing, see “AUTO DISPLAY FUNCTION” for information on how to stop it. • Press M to change from mode to mode. • The animation area shows different animated characters and graphics, depending on the mode and the operation being performed.
PAGE 2
1865-2 To edit Telememo data items TELEMEMO MODE Remaining memory ALM SIG Name M AM PM A DST ALM SIG Telephone number AM PM DST B ALM SIG [New Data Screen] The Telememo Mode lets you store up to 30 pairs of name and telephone number data. Data is automatically sorted based on the characters of the name. You can recall data by scrolling through it on the display. • See the “CHARACTER LIST” at the back of this manual for details on how the watch sorts data.
PAGE 3
1865-3 AUTO DISPLAY FUNCTION The Auto Display function of this watch continually changes the contents of the digital display. Note that you cannot use any of the watch’s other functions (except for backlight) while the Auto Display function is operating. M A ALM SIG To turn the Auto Display Off Hold down M for about three seconds until the watch beeps. AM PM DAY DST To turn the Auto Display On B Hold down M for about three seconds until the watch beeps.