User manual
- 3 -
TELEMEMO MODE
The Telememo Mode lets you store up to 30
pairs of name and telephone number data.
Data is automatically sorted based on the
characters of the name. You can recall data by
scrolling through it on the display.
See the “CHARACTER LIST” for details on
how the watch sorts data.
The new data screen appears when there is
no data stored in memory, or when you scroll
to the location between the last and the first
data items stored in memory.
The data item on the display when you exit
the Telememo Mode appears first the next
time you enter the Telememo Mode.
If you do not operate any button for a few
minutes while in the Telememo Mode, the
watch automatically goes back to the
Timekeeping Mode.
SIG
ALM
SIG
ALM
Remaining memory
Name
Telephone
number
SIG
ALM
[New Data Screen]
To edit Telememo data items
1. In the Telememo Mode, scroll through the data items and display the one you want to
edit.
2. Press and a cursor appears in the animation area.
3. Use to move the flashing to the character you want to change.
4. Use to change the character.
For details on inputting characters, see “To input new Telememo data” (steps 3 for
name input and 7 for number).
5. After making the changes that you want, press to store them and return to the
Telememo Mode data screen.
To delete Telememo data
1. In the Telememo Mode, scroll through the data items and display the one you want to
delete.
2. Press and a cursor appears in the animation area.
3. Hold down and at the same time until the message
CLR
(clear) appears in the
animation area.
At this time the cursor appears in the animation area, ready for input.
4. Input data or press to return to the Telememo Mode data screen.
STOPWATCH MODE
The Stopwatch Mode measures elapsed time and
cumulative elapsed time. The range of the stopwatch is 23
hours, 59 minutes, 59.99 seconds.
To measure elapsed time
1. Press to start the stopwatch.
2. Press to stop the stopwatch.
3. Press to clear the stopwatch to all zeros.
Instead of pressing , you can also clear the stopwatch
by holding down for a few seconds.
1/100 second
SIG
ALM
Hours
Seconds
Minutes
To measure cumulative elapsed time
1. Press to start the stopwatch.
2. Press to stop the stopwatch.
3. Press again to resume timing from the time shown on the display.
You can repeat steps 2 and 3 as many times as you like.
4. Press to clear the stopwatch to all zeros.
Instead of pressing , you can also clear the stopwatch by holding down for a few
seconds.
ALARM MODE
When the Daily Alarm is turned on, the alarm sounds for 20
seconds at the preset time each day. Press any button to
stop the alarm after it starts to sound.
When the Hourly Time Signal is turned on, the watch beeps
every hour on the hour.
To set the alarm time
1. Press while in the Alarm Mode. The hour digits flash
on the display because they are
selected
.
• This operation automatically turns on the Daily Alarm.
2. Press to change the selection in the following
sequence.
A
SIG
ALM
AM indicator
Hour : Minutes
Hourly time signal
on indicator
Alarm on
indicator
Hour
Minutes
3. Press to increase the selected digits. Holding down increases the selection at
high speed.
The format (12-hour and 24-hour) of the alarm time matches the format you select for
normal timekeeping.
When setting the alarm time using the 12-hour format, take care to set the time correctly
as a.m. (A indicator) or p.m. (P indicator).
4. After you set the alarm time, press to return to the Alarm Mode.
If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Alarm Mode automatically.
To turn the Daily Alarm and Hourly Time Signal on and off
Press while in the Alarm Mode to change the status of the Daily Alarm and Hourly
Time Signal in the following sequence.
[Alarm On Indicator/Hourly Time Signal On Indicator]
To test the alarm
Hold down while in the Alarm Mode to sound the alarm.
J
SIG ALM
H
SIG ALM
SIG ALM
H J
SIG ALM
Daily Alarm
Only
Hourly Time
Signal Only
Both ON Both OFF
To input new Telememo data
1. In the Telememo Mode, press until the new data screen
appears.
In the Telememo Mode, the animation area of the display
is used for name input and display.
If the message
FULL
appears in the number area of the
display, it means that memory is full. To store more data,
you will first have to delete some of the data stored in
memory.
2. Press and a cursor appears in the animation area.
3. Use to change the character at the cursor position in
the animation area. The character changes in the following
sequence.
SIG
ALM
Number area
Animation area
Cursor
(space)
A to
Z to
9 .-
Holding down changes the character at high speed.
4. When the character you want is at the cursor position, press to move the cursor to
the right.
5. Repeat the steps 3 and 4 until your text is complete.
You can input up to eight characters for the name.
6. After you input a name, use to move the cursor to the number area.
There are eight spaces provided for input of characters of each name, though only
three characters are visible at a time in the animation area. If the name you input has
less than eight characters, use to move the cursor to the eighth space (which
means you would press three times after inputting a 5-character name, for example).
Pressing again while the cursor is at the eighth space causes it to jump down to the
first digit in the number area. When the cursor is at the 12th digit of the number area,
pressing causes it to jump back up to the first character of the name.
7. Use to change the character (hyphen, number, or space) at the cursor position in
the number area. The character changes in the following sequence.
Holding down changes the character at high speed.
8. When the character you want is at the cursor position, press to move the cursor to
the right.
9. Repeat steps 7 and 8 until you complete number input.
You can input up to 12 digits for the number.
10. After inputting your data, press to store it and return to the Telememo Mode data
screen (without the cursor).
If you do not perform any button operation for few minutes while the cursor is on the
display, the watch automatically returns to the Telememo Mode data screen.
The animation area of the display can show only three characters at a time, so longer
text scrolls continuously from right to left.
The number area can show up to six digits at one time. If a number has more than six
digits, the display automatically switched between the first six digits (counting forward
from the first digit) and the last six digits (counting backward from the last digit) of the
number. This means that if a number is 12 digits long, the number area switches
between the first six digits and the last six digits. If a number is seven digits long, the
number area switches between digits 1 through 6, and digits 2 through 7.
Animation Area Number Area
03-3347-4811
Last letter of text
Separator
(inserted automatically)
SIG
ALM
SIG
ALM
03-123-45
SIG
ALM
SIG
ALM
To recall Telememo data
In the Telememo Mode, press to scroll forward through stored data items.
Holding down scrolls through the data at high speed.
(space)
0 to 9-
M
M
M
M
M
M
M
M
M
M
M
M
M
M
B
B
B
B
B
B
B
B
B
B
B
B B
B
B
B
B
B
B
B
B
B
B
B
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A