Table of Contents www.CasablancaFanCo.com What to Expect with Your Installation Congratulations on purchasing your new Casablanca® ceiling fan! It will provide comfort and performance in your home or office for many years. This installation and operation manual contains complete instructions for installing and operating your fan. Tools Needed Mounting Options 1.888.227.
www.CasablancaFanCo.com What to Expect with Your Installation 1.888.227.2178 Read and Save These Instructions If you are unfamiliar with wiring, use a qualified electrician. This product conforms to UL Standard 507. WARNINGS 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box Know your wiring You may need a friend to help you. Assess location 1 Ceiling angles greater than 34° will require an Angled Mounting Kit.
Tools Needed www.CasablancaFanCo.com Ladder Pliers Wire Strippers 9/64” Drill Bit (optional) Power Drill (optional) If mounting to a support structure, you will also need these tools. 3 M8514-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company Screwdrivers 1.888.227.
34O CEILING Mounting Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately). Angled Mounting Standard Mounting Style Ceiling Outlet Box (required) Use the three steps below to determine if your ceiling angle is greater than 34° 2 1 1.888.227.
Ceiling Bracket www.CasablancaFanCo.com 1.888.227.2178 r we o nP r Tu OFF For angled ceilings, point opening toward peak. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31.
Option 1 Downrod www.CasablancaFanCo.com 1.888.227.
Downrod (continued) KEEP! (not to scale) 8” & 3/8” 1.888.227.2178 STRIP CUT www.CasablancaFanCo.com ! KEEP Remove the pre-installed setscrew so that the downrod can be inserted. The wires can be cut, but leave at least 8” extending from the top of the downrod. Hand tighten the downrod (at least 4-5 full turns) until it stops. 8” Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. 3/8” If the setscrew is not tightened securely, the fan may fall.
Downrod (continued) Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. www.CasablancaFanCo.com DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. 8 M8514-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company 1.888.227.
Wiring Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. www.CasablancaFanCo.com 1.888.227.2178 OM CEILING FR Receiver green/yellow stripe (grounding) Using an orange wire connector from the hardware bag: Connect the 3 grounding wires (green, green/yellow stripe, or bare copper) coming from the ceiling, downrod, and ceiling bracket.
Wiring (continued) www.CasablancaFanCo.com OM FR OM CEILING FR • Connect the blue wire from the receiver to the blue wire (or possibly black with white stripe wire) from the fan. • Connect the white (grounded) wire from the ceiling to both the white wire from the receiver and the white wire from the fan. FRO white FR M FA N OM FAN FR OM white Connect the black (ungrounded) wire from the ceiling to the black wire from the receiver.
Wall Control www.CasablancaFanCo.com Screw Cut-Out 1.888.227.2178 Drywall Drill Holes Before Drywall Anchors Template Painter’s Tape Cover Plate Template Template After 1. Tape the provided wall control template with painter’s tape at the desired installation area. 2. Drill holes inside the four corners of the template. Note: Make sure the wall control template is level before proceeding to the next step. 1.
Canopy www.CasablancaFanCo.com Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. 12 M8514-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company 1.888.227.
Blades www.CasablancaFanCo.com Attach a blade tip to each blade using two blade tip screws, found in the hardware bag. Insert four blade assembly screws and four blade washers, found in the hardware bag, into each blade as shown. Install the screws into the posts in each blade arm. 13 M8514-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company 1.888.227.
Globe www.CasablancaFanCo.com 1.888.227.2178 Tab Notch Globe CONGRA T YOU’REULATIONS! DONE! Position the notches in the outer rim of the globe so they line up with the tabs on the inside of the rim on the light kit. Carefully lift the globe up inside the light kit as far as it will go, then rotate the globe clockwise until it is held tightly in place by the four tabs. 14 M8514-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company See next page for fan operation instructions.
Operation www.CasablancaFanCo.com er w o nP Battery Battery Holder 1.888.227.2178 r Tu ON Battery Door The remote transmitter is already paired to the receiver and ready to use. Before operating the wall control, press on the battery door to eject it. Unscrew the battery holder. Insert the battery, found in the control hardware bag, with the positive (+) side facing downward. Reinstall the battery holder and reinsert the battery door into the wall control.
Operation (continued) www.CasablancaFanCo.com Reverse Button Fan Speed (Low) Fan Speed (a) 1.888.227.2178 The Safe-Exit Program gives you about thirty seconds of light when you turn the lights off to exit the room before the lights go out. To use Safe-Exit: • Press the fan power button off for at least three seconds to initiate the Safe-Exit Mode. (High) Lights Down Lights Up Reverse Fan Power • The lights will flash for visual confirmation.
Maintenance & Cleaning www.CasablancaFanCo.com er w o nP r Tu OFF Be sure to turn off power to the fan before performing any maintenance or relamping. Cleaning the fan - use soft brushes or cloths to prevent scratching. Cleaning products may damage the finishes. 17 M8514-01 • 04/16/15 • © 2013–2015 Casablanca Fan Company 1.888.227.2178 Casablanca fans have the power to cut your cooling costs up to 40%.
Troubleshooting www.CasablancaFanCo.com Fan doesn’t work Excessive wobbling Remote does not work • Press a fan speed button (1-4). • Tighten all of the blade screws until they are snug. • Make sure the battery is installed correctly. • Turn the power off, support the fan carefully, and check that the hanger ball is properly seated. • Install a new battery. • Check the circuit breaker to ensure the power is turned on. • Check the wall control battery. • Make sure the blades spin freely.
Troubleshooting (continued) www.CasablancaFanCo.com Installing Multiple Fans with Independently Operating Remote Controls 1.888.227.2178 Installing One Fan Operating on Multiple Remote Controls To install multiple fans with independently operating remote controls, there is no need to perform any pairing procedures. Each set of receiver/transmitter is already paired. Simply install each receiver into a fan and use the appropriate transmitter to operate each fan.
