CAPISTRANO™ OWNER’S MANUAL Casablanca 13
CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 MOUNTING RECOMMENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 PREPARATION INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 FAN INSTALLATION . . . . . . . . . . . . . . . . . . . . . .
MOUNTING RECOMMENDATIONS Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and fan size are all important factors to consider before installation. Location Ceiling fans have practical uses in almost every room in your home. We suggest you follow these mounting recommendations as you decide where to install your Casablanca fan. • For safety reasons, the fan blades must be a minimum of 7′ above the floor.
CAPISTRANO Casablanca PREPARATION INSTRUCTIONS Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them against the parts listed here. Before discarding packaging material, be certain that all parts have been removed.
CAPISTRANO Casablanca CROSSBAR MOUNTING BRACKET INSTALLATION Proceed with installation as follows: Step 1. Route the wires from the ceiling outlet box through the crossbar mounting bracket center hole. Attach the bracket, with ground wire and ridges down, to the ceiling fixture outlet box with the mounting hardware included with the outlet box. Tighten the screws firmly by hand only, being careful not to bend the bracket by over tightening.
CAPISTRANO Casablanca HANGING THE FAN Step 3. To hang the fan body in the canopy, hold the fan body firmly and insert the ball into the canopy opening. Check that no wires were pinched. Rotate the fan body until the slot in the ball fits into the pin opposite the canopy opening. BALL Fan Hanging Weight is 24 lbs Note: Independent control of the light fixture using a W-8/W-811 requires an additional independent power wire run from the wall switch to the fan. See Page 10 for wiring.
CAPISTRANO Casablanca INSTALLING THE BLADE/BLADE HOLDER TO FAN MOTOR PREPARATION Step 8. To reach the blade holder mounting holes in the fan motor the dummy switch housing must be removed. Take out the two 5-32 X 9/32” screws securing the dummy switch housing and remove. Put the two (2) screws aside for the moment, they will be used in Step 15 to install the switch housing after the blades are installed. The dummy switch housing is used only when shipping the fan.
CAPISTRANO Casablanca BLADE INSTALLATION Step 10. Attach each blade to a blade holder securing it with the four blade screws provided. Using the screwdriver, tighten securely by hand only. BLADE SCREW (4 PER BLADE) BLADE BLADE HOLDER REMOVE SHIPPING BLOCKS Step 11. On the flywheel remove the five shipping blocks by unscrewing the screws. Set these screws aside for installing the blades in Step 12. SHIPPING BLOCKS Discard the five shipping blocks.
CAPISTRANO Casablanca COMPLETING INSTALLATION SWITCH HOUSING MOUNT SCREW (REMOVED IN STEP 8) 5-32 X 9/32″ (2) SWITCH HOUSING AND CAP ASSEMBLY PREPARATION Step 13. Locate the switch housing/cap assembly and remove the two 8-32 X 3/8″ screws holding the cap onto the switch housing. Note: Save these two screws–they will be used in Step 18! SWITCH HOUSING SWITCH HOUSING CONNECTOR (SOCKET) REVERSE SWITCH CAP PULL CHAIN SWITCH CAP SCREW 8-32 X 3/8″ (2) CONNECTING THE SWITCH HOUSING ASSEMBLY Step 14.
CAPISTRANO Casablanca INSTALLING THE SWITCH HOUSING ASSEMBLY Step 15. Line up the two inner clearance holes in the cap with the two threaded holes in the switch mounting plate standoffs. CAUTION! Before continuing to the next step check that a wire or component inside the switch housing will not be pinched as it is installed. Step 16. Use the two (2) 5-32 X 9/32″ screws removed in Step 8 to install the switch housing assembly. Tighten securely by hand only.
3-SPEED ♦ W-4/W-411 WALL CONTROL OF THE FAN • The W-4 allows the choice of four (4) different speed settings. • No light fixture is used. • Set the FAN pull chain switch to the HIGH speed setting. • No changes in household or fan wiring are required. • The fan may be turned ON and OFF by the W-4 wall control. CAUTION! Failure to set the pull-chain speed to HIGH can result in faulty operation of the fan and damage to the W-4/W-411 wall control.
3-SPEED ♦ OPERATION Pull-chain switches on the fan control the fan and lights. Using the fan control pull-chain switch: Fan off at start. First pull: fan ON, low speed Second pull: medium speed Third pull: high speed Fourth pull: fan OFF Using the optional light pull-chain switch: Light off at start. First pull: light ON Second pull: light OFF Direction of blade rotation is controlled by the reverse slide switch on the side of the switch housing. No changes in household wiring are required.
TROUBLESHOOTING Before Requesting Service: Please follow this troubleshooting guide before contacting your dealer for assistance. Caring for Finishes: For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish. A vacuum cleaner brush nozzle can remove heavier dust. Surface smudges or an accumulation of dirt and dust can easily be removed by using a mild detergent and slightly dampened soft cloth. An antistatic agent may be used, but never use abrasive cleaning agents.
7 6 1 C O R P O R A T E © C C E N T E R O P Y R IG H T D • R IV E 1 9 9 8 C P O M O N A A S A B L A N C A F A N , C A 9 1 7 6 8 C O M P A N Y • • U .S .
