User manual

27
GB
CARSON Brushless Speed Controller Dragster 6S
Turn off the ESC
Turn off the transmitter
Hold the set key,
switch on the ESC
Red LED flashes
ca. 8 seconds
Green LED flashes
for 1 time
Green LED flashes
for 2 times
Green LED flashes
for 3 times
Green LED flashes
for 4 times
Green LED flashes
for 5 times
Enter the 1st adjustment
“Running Mode”
Enter the
2nd adjustment
“Drag Brake Force” in
neutral position
Enter the
3rd adjustment
“Low Voltage Cut-Off”
Enter the
4th adjustment
“Accelleration mode”
Enter the 5th adjustment
„Max. braking force”
Red LED flashes for 1 time to choose
“Forward with brake”
Red LED flashes for 2 times to choose
“Forward/reverse with brake”
Red LED flashes for 3 times to choose
“Forward and reverse”
Red LED flashes for 1 time, choose “0%”
Red LED flashes for 2 times, choose “5%”
Red LED flashes for 3 times, choose “10%”
Red LED flashes for 4 times, choose “20%”
Red LED flashes for 5 times, choose “40%”
Red LED flashes for 6 times, choose “60%”
Red LED flashes for 7 times, choose “80%”
Red LED flashes for 8 times, choose “100%”
Red LED flashes for 1 time, choose “None”
Red LED flashes for 2 times, choose “2.6 V”
Red LED flashes for 3 times, choose “2.8 V”
Red LED flashes for 4 times, choose “3.0 V”
Red LED flashes for 5 times, choose “3.2 V”
Red LED flashes for 6 times, choose “3.4 V”
Red LED flashes for 1 time, choose “Level 1“
Red LED flashes for 2 times, choose “Level 2“
Red LED flashes for 3 times, choose “Level 3“
Red LED flashes for 4 times, choose “Level 4“
Red LED flashes for 5 times, choose “Level 5“
Red LED flashes for 6 times, choose “Level 6“
Red LED flashes for 7 times, choose “Level 7“
Red LED flashes for 8 times, choose “Level 8“
Red LED flashes for 9 times, choose “Level 9“
Red LED flashes for 1 time, choose “25%“
Red LED flashes for 2 times, choose “50%“
Red LED flashes for 3 times, choose “75%“
Red LED flashes for 4 times, choose “100%“
Red LED flashes for 5 times, choose
“deactivated”
Enter the corresponding
programmable adjustment, the
red LED flashes for several times,
the times present the current
value of this item.
Finish programming, switch off the ESC, and then switch it on.
Press the SET key to choose
the programmable value, the
RED LED flashes for several
times, the times present the
serial number of the value
you are choosing.
✼ = 1 sec
✼ = 3 sec
Attention
Value Blinking
frequency
1
✼
2
✼ ✼
3
✼ ✼ ✼
4
✼ ✼ ✼ ✼
5
✼ ✼ ✼ ✼ ✼
6
✼ + ✼
7
✼ + ✼ ✼
8
✼ + ✼ ✼ ✼
Release
SET key
Hold SET key for 3 seconds
Press
SET key
Hold on the button
Hold on the button
Release
SET key
Hold SET key for 3 seconds
Press
SET key
Release
SET key
Hold SET key for 3 seconds
Press
SET key
Release
SET key
Press
SET key
Release
SET key
Press
SET key
Flowchart: Program the ESC with the SET key.