KSAIF0101AAA, KSAIF0201AAA, KSAIF0301AAA, KSAIF0401AAA, KSAIF0501AAA, KSAIF0601AAA Wi-Fi Interface Kit for Ductless Systems OWNER’S MANUAL NOTE: Read and become familiar with these instructions before beginning installation. TABLE OF CONTENTS PAGE SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 WIRELESS NETWORK TYPE .
SAFETY CONSIDERATIONS Installing, starting up, and servicing air−conditioning equipment can be hazardous due to system pressures, electrical components, and equipment location (roofs, elevated structures, etc.). Only trained, qualified installers and service mechanics should install, start−up, and service this equipment. Untrained personnel can perform basic maintenance functions such as cleaning coils. All other operations should be performed by trained service personnel.
! WARNING ELECTRICAL SHOCK HAZARD Failure to follow this warning could result in personal injury or death. Before installing, modifying, or servicing system, main electrical disconnect switch must be in the OFF position. There may be more than 1 disconnect switch. Lock out and tag switch with a suitable warning label. ! WARNING EXPLOSION HAZARD Failure to follow this warning could result in death, serious personal injury, and/or property damage.
OVERVIEW For the utilization of the hardware provided in the Wi−Fi kits (KSAIF0101AAA, KSAIF0201AAA, KSAIF0301AAA, KSAIF0401AAA, KSAIF0501AAA, and KSAIF0601AAA), the home owner/end user needs to download the mobile app. The app is available in the App Store for iOS devices and Google Play for Android devices. Instructions for downloading and using the Carrier/Bryant/Payne/Midea apps are listed within this document. Applicable Systems: IOS, ANDROID IMPORTANT: We recommend iOS 7.0, Android 4.0 or later.
WIRELESS NETWORK TYPE S The Wi−Fi kits are only supported by WPA−PSK/WPA2−PSK encryption and no encryption. WPA−PSK/WPA2−PSK encryption is recommended. ! S S S S S CAUTION Please check the router website for more information. Smart phone cameras require a minimum of 5 million pixels to ensure the QR code is scanned appropriately. Due to different network configurations, request time−outs may occur thus it may be necessary to configure the network again.
DOWNLOAD AND INSTALL APP S S Android Phone Users: Go to google play, search for the Carrier CliMate, Bryant ControlBox, Payne Panel, or Midea Air app depending on the type of equipment installed and download it. iPhone Users: Go to the App Store, search for the Carrier CliMate, Bryant ControlBox, Payne Panel, or Midea Air app and download it. USER REGISTRATION IMPORTANT: S S Ensure your mobile device is connected to the same Wi−Fi router that your fan coil is connected to.
MULTIPLE SMART PHONE DEVICE CONTROL The app can run on multiple devices in a household. Just download the app to other devices and sign in to the SAME account using the user name and password used to setup the system. NOTE: Setting up the system again in a different smart phone device with a different user name will remove the unit from the first smart phone device.
ANDROID CONFIGURATION PROCESS 1. Ensure your mobile device has already been connected to the desired Wi−Fi network. It is recommended to forget all networks except the one used to connect the fan coil to prevent configuration errors. 2. Disconnect the power supply from the Ductless system and wait thirty (30) seconds. 3. Reconnect the power supply to the Ductless system. 4. Press LED or DO NOT DISTURB button on the wireless remote seven (7) times in three (3) minutes.
7. Your device may request approval for the app to utilize the mobile device camera. Select OK. 8. Add a system using one of the 2 following methods: a. Scan the QR Code which was provided with the Wi−Fi Kit. Fig. 3 - Scan the QR Code b. Alternatively a system can be added using the option to Choose the type of appliance as ’AC’ and following the prompts on the screen.
9. Select the Wi−Fi network desired and enter the Wi−Fi password. Fig. 4 - Select Wi−Fi password NOTE: The app may take up to 3 minutes to configure the Wi−Fi kit for connectivity to your Wi−Fi network.
Configuration is now complete. The default name for the unit connected appears on the home screen. Fig.
iOS CONFIGURATION PROCESS 1. Ensure your mobile device has already been connected to the Wi−Fi network which you want to use. It is recommended to forget all networks except the one used to connect the fan coil to prevent configuration errors. 2. Disconnect the power supply from the Ductless system and wait thirty (30) seconds. 3. Reconnect the power supply to the Ductless system. 4. Press LED or DO NOT DISTURB seven (7) times in 3 minutes.
7. Your device may request for approval for the app to utilize the mobile device camera. Select OK. 8. Scan the QR Code which was provided with the Wi−Fi Kit. Fig.
9. Follow the on screen instructions on your mobile device and press HOME to return to the device interface. 10. Click the setting icon on the mobile device, and then select the Wi−Fi menu. 11. From the wireless networks shown, select ’net_ac_XXXX’ Fig.
12. Enter the default password: 12345678 and press Join. Fig.
13. Once the connection has been made with the “net_ac_xxxx” network, return to the Carrier CliMate, Bryant ContolBox, Payne Panel, or Midea Air app. 14. Click Next at the top right of the screen. Fig.
15. Select the Wi−Fi network desired and enter the Wi−Fi password. Fig. 11 - Select Wi−Fi network − enter Wi−Fi password Configuration is now complete, and the default name for the connected unit appears on the home screen. NOTE: The app may take up to 3 minutes to configure the Wi−Fi kit for connectivity to your Wi−Fi network.
Fig. 12 - Configuration complete NOTE: S S When the network configuration is complete, the app confirms whether the connection was successful or not. Due to different LAN configuations, it is possible that the device status will display “OFFLINE”. If this occurs, it is necessary to refresh the device list by pulling down on the list shown on the app home screen or the ductless system power can by cycled and the device status will change to “ONLINE” after a few minutes.
HOW TO USE THE APP Basic Functions IMPORTANT: Prior to using the app, verify your mobile device and ductless system are connected to the Internet. 1. Log into the app. Fig.
2. Select the desired ductless system to enter the main control interface. Fig.
3. From the main control interface the user can control the ductless system’s on/off status, operation mode, temperature, fan speed, etc. by touching the buttons at the bottom of the screen. Current Room Temperature set point and mode More informa on Turbo ON / OFF Fan speeding se ng Other Opera ons Fig. 15 - Main Control Interface NOTE: Not all functions are available for every ductless system.
ON/OFF The ON/OFF soft button allows the user to turn off the ductless system. Once touched, the screen will change to one of the colors shown in Figure 16 (color depends on which mode was last operational at the time the system was turned off). Auto Dry Cool Heat Fig. 16 - ON/OFF Soft Buttons To turn the system on again, touch the logo in the middle of the screen.
MODES There are five (5) different modes available in the app. These modes are AUTO, COOL, DRY, HEAT, and FAN. When the user touches MODE the Mode menu appears (see Figure 17). Fig. 17 - Mode The user can touch any of the modes to set the unit mode. IMPORTANT: When using the App to control the space setpoint and mode, the wireless or wired controller (where applicable) will not update with the settings from the app.
AUTO Mode AUTO mode allows the ductless system to shift between the heating and cooling mode to maintain the setpoint. The dead band between setpoint and controllability is 2_F (1_C) and cannot be adjusted within the app. When this mode is selected, the screen color will change (see Figure 18). Fig.
COOL Mode The COOL mode allows the ductless system to lock into cooling mode ONLY and condition the space by cooling the air to the setpoint. If the space temperature is lower than the setpoint, the ductless system turns off. When this mode is selected, the screen color will change (see Figure 19). Fig.
DRY Mode The DRY mode locks the ductless system into the cooling mode and reduces airflow to increase the water removal from the space. Conditioning of the space is done by cooling the air to the setpoint. If the space temperature is lower than the setpoint, the ductless system turns off. When this mode is selected, the screen color will change (see Figure 20). Fig.
HEAT Mode The HEAT mode allows the ductless system to lock into heating mode ONLY and condition the space by heating the air to the setpoint. If the space temperature is higher than the setpoint, the ductless system turns off. When this mode is selected, the screen color will change (see Figure 21). Fig.
FAN Mode The FAN mode allows the ductless system to turn off except for the indoor fan. This mode is intended to circulate air through the space without conditioning it with the refrigeration system. When this mode is selected, the screen color will change (see Figure 22). Fig.
Setting the Temperature set point Once the operation mode is selected, setting the desired indoor temperature set point is usually desired. To do this, drag your finger up or down over the temperature setting number on the main screen. Fig.
Fan Speed Settings There are 4 fan speed options available to the user. These options are AUTO, HIGH, MID, and LOW. NOTE: These speeds are available only when the system is set to the COOL or HEAT modes. Changing fan speeds is not available in the AUTO or DRY modes. The adjustments to the fan speed should be done to improve the comfort of the occupant(s). When the fan speed setting soft button is pressed, the mode menu appears (see Figure 24). Fig.
TURBO − TURBO is only available after the COOL mode is selected. TURBO is designed to decrease the time it takes for the space to achieve setpoint by triggering the compressor and fan to immediately move to the high speed. Lover Controls − the app provides 2 different louver controls, horizontal ( ) and ). The use of these functions are dependent on the type of fan coil vertical control ( currently installed and if it has a vertical and/or horizontal louver control.
Timer On/Timer Off 7 day programmable features are available to set on and off times for the ductless system to condition the space. Fig.
14_F (8_C) Heating Setback/Vacation Mode This feature allows the ductless system to enter a setback/vacation mode when the space is or will be unoccupied. The ductless system will follow the current space temperature setpoint less 14_F to protect the space from frost damage. Sleep This feature allows the user to customize the space temperatures throughout a sleep cycle of 8hrs by setting a targeted temperature for each hour of the cycle.
System Check A systems health check can be performed in the check screen. This function informs the user or service technician of normal items, abnormal items, and detailed information about the operating characteristics of the ductless system. Fig.
Fan Coil Deletion from App In the event a fan coil is decommissioned or a user moves from a location where a Wi−Fi kit is installed, the ductless system can be removed from the app by entering the Information menu via the function menu accessible from the icon in the top right of the home screen. Fig. 28 - Fan Coil Deletion from App Cautions S The Wi−Fi kit complies with 47cfr sub−part 15 and RSS 210 of the Industry and Science of Canada. Operation is subject to the following conditions: 1.
TROUBLESHOOTING Table 1—Troubleshooting Issue Connection failure between the Wi-Fi AC and home router Connection failure between router and cloud server System removed from the App when other user adds the system. Resolution Wrong password inputted.: If there is no response for a long time, please re-connect from AP mode and try and repeat the network setup process. Password contains special characters.
