Specifications

VLT SERIES 2000 PARAMETER GROUPS AND FACTORY DEFAULT SETTINGS
OPERATION and
DISPLAY:
000 LANGUAGE SELECT
S)
ENGLISH
001 MENU SETUP SELECT
S)
SETUP 1
002 SETUP COPY
DO NOT COPY
003 LOCAL REMOTE
S)
REMOTE
004 LOCAL REFERENCE
S)
0 Hz
005 DISPLAY VALUE
S)
1000
006 LOCAL RESET
S)
ENABLE
007 LOCAL START/STOP
S)
ENABLE
008 LOCAL REVERSING
S)
DISABLE
009 LOCAL JOGGING
S)
ENABLE
010 LOCAL SPEED
SELECT
S)
ENABLE
013 DATA CHANGE LOCK
S)
NOT LOCKED
LOAD and
MOTOR:
101 SPEED CONTROL
2,S)
SLIP COMPENSATED
102 CURRENT LIMIT CONT.
S)
PROGRAMMED SET
103 MOTOR POWER
NOMINAL SIZE
104 MOTOR VOLTAGE
DEPENDING ON UNIT
105 MOTOR FREQUENCY
DEPENDING ON UNIT
107 MOTOR CURRENT
2, S)
DEPENDING ON UNIT
108 MOTOR MAGNETIZE
2,S)
DEPENDING ON UNIT
109 START VOLTAGE
2, S)
DEPENDING ON UNIT
110 START COMP
2,S)
DEPENDING ON UNIT
111 U/F RATIO
2,S)
DEPENDING ON UNIT
112 SLIP COMP
2, S)
DEPENDING ON UNIT
114 FEEDBACK SIGNAL
S)
CURRENT 20mA
119 FEED FWD FACTOR
2, S)
100%
120 CONTROL RANGE
42 S)
100%
121 PROPORTION GAIN
2, S)
0.01
122 INTEGRAL TIME
2, S)
OFF
125 FEEDBACK SCALING
2, S)
100%
REFERENCES and
LIMITS:
200 FREQUENCY RANGE
0-120 Hz
201 MIN. FREQUENCY
2, S)
0.00 Hz
202 MAX. FREQUENCY
2, S)
DEPENDING ON UNIT
203 JOG FREQUENCY
2, S)
10
204 DIGITAL REF. TYPE
2, S)
SUM
205 DIGITAL REF. 1
2, S)
00.0
206 DIGITAL REF. 2
2, S)
0
207 DIGITAL REF. 3
2, S)
0
208 DIGITAL REF. 4
2, S)
0
209 CURRENT LIMIT
2, S)
DEPENDING ON UNIT
210 WARN FREQ. LOW
2, S)
0
211 WARN FREQ. HIGH
2, S)
f
RANGE
(from 200)
213 WARN CURRNT HIGH
2,S)
I
VLT MAX
(from 209)
215 RAMP-UP TIME
2, S)
5 SEC
216 RAMP-DOWN TIME
2, S)
5 SEC
218 QUICK-STOP RAMP
1 SEC
224 CARRIER FREQ
2, S)
4.5
230 SPEED UP/DOWN
DISABLE
FUNCTIONS and
TIMERS:
300 BRAKE FUNCTION
S)
NOT APPLIED
306 DC BRAKING TIME
2, S)
0
307 DC BRAKE CUT-IN
FREQUENCY
2, S)
1
308 DC BRAKE VOLTAGE
2, S)
10
309 RESET MODE
S)
MANUAL RESET
310 TRIP DELAY AT
CURRENT LIMIT
S)
INFINITE
315 MOTOR THERMAL
2, S)
PROTECTION
OFF
INPUTS and
OUTPUTS:
402 TERMINAL 18 START
S)
START
403 TERMINAL 19
REVERSING
S)
REVERSING
404 TERMINAL 27 STOP
S)
MOTOR COASTING
405 TERMINAL 29 INPUT
S)
JOG
408 TERMINAL 46 OUTPUT
S)
UNIT READY
REMOTE CONTROL
409 TERMINAL 01
RELAY OUTPUT
S)
READY
411 ANALOG REF. TYPE
S)
LINEAR
412 TERMINAL 53
ANALOG VOLTAGE
2, S)
0-10VDC
413 TERMINAL 60
ANALOG I
2, S)
0-20 mA
SERIAL DATA
INTERFACE:
500 ADDRESS
1
501 BAUD RATE
1.2 K
502* DATA READ-OUT
S)
503* COASTING
S)
OR
504* Q-STOP
S)
OR
505* DC BRAKE
S)
OR
506* START
S)
OR
507* DIRECTION
S)
DIGITAL
508* RESET
S)
OR
509* SET-UP SELECT
S)
OR
510* SPEED SELECT
S)
OR
511 BUS JOG 1
S)
10
514 BUS BIT 4
S)
Q-STOP
516 BUS REFERENCE
S)
0
517 STORE DATA VALUES
S)
OFF
SERVICE and
DIAGNOSTICS:
606 TOTAL OPERATION
HOURS
607 RUNNING HOURS
608 NUMBER OF
POWER UPS
609 NIMBER OVER-TEMP
610 NUMBER OF
OVER-VOLTAGE
46
DISPLAY MODE
READOUTS:
REFERENCE %
FREQUENCY Hz
DISPLAY FEEDBACK "UNIT"
CURRENT A
TORQUE %
POWER kW
POWER HP
ENERGY KWh
OUTPUT VOLYAGE V
DC VOLTAGE V
MOTOR ETR value %
INVERTER ETR value %
* NOTE: Menu 502 can only be selected from the bus.
These values are read-only values.
The PC/PLC may prompt for a value from an index
between 0 and 19.
In parameters 503 to 510 you can choose to control
the VLT adjustable frequency drive via the control
unit's terminals (digitally) and or via the bus.
When using Logical and Bus values in parameters
503-510, the digital control terminals are either
dependent on or overruled by the bus commands.
2) AVAILABLE IN BOTH SETUPS
S) CAN BE CHANGED IN START MODE (RUNNING MOTOR)